
Here - Tenaga Nasional Berhad
... Supply may be provided at any of the declared voltages :275 kV, 132kV, 33kV, 22 kV*, 11kV, 6.6 kV* and 400/230V. Generally, supplies to domestic premises are given at single phase 2-wire or three phase 4-wire while for non domestic premises the supply are at three phase 3-wire or three phase 4-wire. ...
... Supply may be provided at any of the declared voltages :275 kV, 132kV, 33kV, 22 kV*, 11kV, 6.6 kV* and 400/230V. Generally, supplies to domestic premises are given at single phase 2-wire or three phase 4-wire while for non domestic premises the supply are at three phase 3-wire or three phase 4-wire. ...
AEM EMS User Guide V2.0
... It is recommended to leave the default target installation directory (c:/Program Files/AEM) unchanged, this will simplify future updates Restart the PC ...
... It is recommended to leave the default target installation directory (c:/Program Files/AEM) unchanged, this will simplify future updates Restart the PC ...
ADC Successive Approximation Register
... practice is to stop conversions with ADC_StopConvert(), change the resolution, then restart the conversions with ADC_StartConvert(). If you decide not to stop conversions before calling this API, use ADC_IsEndConversion() to wait until conversion is complete before changing the resolution. If you ca ...
... practice is to stop conversions with ADC_StopConvert(), change the resolution, then restart the conversions with ADC_StartConvert(). If you decide not to stop conversions before calling this API, use ADC_IsEndConversion() to wait until conversion is complete before changing the resolution. If you ca ...
Instructions for Installation, Operation, and Maintenance
... framework of the switchgear assembly). To open a manually operated MVS2 switch insert the operating handle and push down. When the switch opens the door may be opened. When handling MVS switchgear, be sure the switches are in the closed position. Do not operate MVS2 switches unless the switchgear as ...
... framework of the switchgear assembly). To open a manually operated MVS2 switch insert the operating handle and push down. When the switch opens the door may be opened. When handling MVS switchgear, be sure the switches are in the closed position. Do not operate MVS2 switches unless the switchgear as ...
section 261300 - medium voltage outdoor metal clad
... Operating, test and withdrawn positions shall be provided for the breaker unit. The primary contacts shall be disconnected in the test position, but auxiliary contacts and control circuit contacts shall be maintained in this position or shall have means of being connected for breaker and control cir ...
... Operating, test and withdrawn positions shall be provided for the breaker unit. The primary contacts shall be disconnected in the test position, but auxiliary contacts and control circuit contacts shall be maintained in this position or shall have means of being connected for breaker and control cir ...
section 15185 - hydronic pumps
... pump and system curve and translate it to electrical data. This allows the drive to know exactly where it is in the hydronic world. i. Setup two: This subroutine shall allow two pumps to run as backup for each other and shall alternate the pumps based on a real time clock. ii. Setup three: This subr ...
... pump and system curve and translate it to electrical data. This allows the drive to know exactly where it is in the hydronic world. i. Setup two: This subroutine shall allow two pumps to run as backup for each other and shall alternate the pumps based on a real time clock. ii. Setup three: This subr ...
MAX6746–MAX6753 µP Reset Circuits with Capacitor-Adjustable Reset/Watchdog Timeout Delay General Description
... debouncing network. MR is internally pulled up to VCC and, therefore, can be left unconnected if unused. MR is designed to reject fast, falling transients (typically 100ns pulses) and it must be held low for a minimum of 1µs to assert the reset output. A 0.1µF capacitor from MR to ground provides ad ...
... debouncing network. MR is internally pulled up to VCC and, therefore, can be left unconnected if unused. MR is designed to reject fast, falling transients (typically 100ns pulses) and it must be held low for a minimum of 1µs to assert the reset output. A 0.1µF capacitor from MR to ground provides ad ...
Design Guide VT82C694X Apollo Pro133A with VT82C686A South
... No license is granted, implied or otherwise, under any patent or patent rights of VIA Technologies. VIA Technologies makes no warranties, implied or otherwise, in regard to this document and to the products described in this document. The information provided by this document is believed to be accur ...
... No license is granted, implied or otherwise, under any patent or patent rights of VIA Technologies. VIA Technologies makes no warranties, implied or otherwise, in regard to this document and to the products described in this document. The information provided by this document is believed to be accur ...
IQS 23 Family
... Place additional grounded copper around the Cx pads, but not close enough to reduce touch sensitivity below that which is acceptable for the application at hand. ...
... Place additional grounded copper around the Cx pads, but not close enough to reduce touch sensitivity below that which is acceptable for the application at hand. ...
PMBus™ Power Syste em Management Pr rotocol
... statutory, including but not limited to any warranty of merchantability, noninfringement, or fitness for any particular purpose, or any warranty otherwise arising out of any proposal, specification or sample. In no event will any specification co-owner be liable to any other party for any loss of pr ...
... statutory, including but not limited to any warranty of merchantability, noninfringement, or fitness for any particular purpose, or any warranty otherwise arising out of any proposal, specification or sample. In no event will any specification co-owner be liable to any other party for any loss of pr ...
[26 36 33] [16495] - Schneider Electric
... Section Includes: The work specified in this Section includes, but shall not be limited to, solid state, three-phase STS to be used for connecting critical loads to one of two independent sources in redundant power supply systems. In addition to hardware and software design criteria, the theory of n ...
... Section Includes: The work specified in this Section includes, but shall not be limited to, solid state, three-phase STS to be used for connecting critical loads to one of two independent sources in redundant power supply systems. In addition to hardware and software design criteria, the theory of n ...
Service Manual
... Remove all jewelry when working near electrical components. Turn the key switch off (O) and disconnect the batteries before servicing electrical components. Never work under a machine without safety blocks or stands to support the machine. Do not dispense flammable cleaning agents, operate the machi ...
... Remove all jewelry when working near electrical components. Turn the key switch off (O) and disconnect the batteries before servicing electrical components. Never work under a machine without safety blocks or stands to support the machine. Do not dispense flammable cleaning agents, operate the machi ...
Opto-isolator
In electronics, an opto-isolator, also called an optocoupler, photocoupler, or optical isolator, is a component that transfers electrical signals between two isolated circuits by using light. Opto-isolators prevent high voltages from affecting the system receiving the signal. Commercially available opto-isolators withstand input-to-output voltages up to 10 kV and voltage transients with speeds up to 10 kV/μs.A common type of opto-isolator consists of an LED and a phototransistor in the same opaque package. Other types of source-sensor combinations include LED-photodiode, LED-LASCR, and lamp-photoresistor pairs. Usually opto-isolators transfer digital (on-off) signals, but some techniques allow them to be used with analog signals.