DI-718BX Data Logger/Data Acquisition System Hardware Manual
... DATAQ Instruments, Inc., except as otherwise indicated and shall not be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any human or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual, or otherwise withou ...
... DATAQ Instruments, Inc., except as otherwise indicated and shall not be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any human or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual, or otherwise withou ...
SE-130WA-TTL-B datasheet V1.1 2013015
... a 2.4G antenna. The WIFI MODULE provides for the highest-level integration, featuring 802.11b/g and 802.11n. It includes a 2.4 GHz WLAN CMOS power amplifier (PA) that meets the output power requirements of most handheld systems. An optional external low-noise amplifier (LNA) and external PA are also ...
... a 2.4G antenna. The WIFI MODULE provides for the highest-level integration, featuring 802.11b/g and 802.11n. It includes a 2.4 GHz WLAN CMOS power amplifier (PA) that meets the output power requirements of most handheld systems. An optional external low-noise amplifier (LNA) and external PA are also ...
Universal Serial Bus Microcontroller
... The occurrence of a reset is recorded in the Status and Control Register located at I/O address 0xFF (Figure 6-3). Reading and writing this register are supported by the IORD and IOWR instructions. Bits 1, 2, and 7 are reserved and must be written as zeros during a write. During a read, reserved bit ...
... The occurrence of a reset is recorded in the Status and Control Register located at I/O address 0xFF (Figure 6-3). Reading and writing this register are supported by the IORD and IOWR instructions. Bits 1, 2, and 7 are reserved and must be written as zeros during a write. During a read, reserved bit ...
AD7886 LC2MOS 12-Bit, 750 kHz/1 MHz, Sampling ADC
... designed code transitions occur on integer multiples of 1 LSB. The output code is natural binary with 1 LSB = FS/4096. FS is either +5 V or +10 V, depending on how the analog inputs are configured. ...
... designed code transitions occur on integer multiples of 1 LSB. The output code is natural binary with 1 LSB = FS/4096. FS is either +5 V or +10 V, depending on how the analog inputs are configured. ...
Cascaded H-Bridge Multilevel Inverter Using PIC16F877A Controller
... A Micro-controller based gating circuit generates the pulses required by the inverter. The induction motor drive system is successfully fabricated and tested. This can be important in the high power quality cascaded multilevel inverters which ...
... A Micro-controller based gating circuit generates the pulses required by the inverter. The induction motor drive system is successfully fabricated and tested. This can be important in the high power quality cascaded multilevel inverters which ...
ESP8266 System Description
... perform either as a standalone application, or as a slave to a host MCU. When ESP8266EX hosts an application, it promptly boots up from the external flash. The integrated highspeed cache optimizes the system's performance and memory. Also, ESP8266EX can be applied to any micro-controller design as a ...
... perform either as a standalone application, or as a slave to a host MCU. When ESP8266EX hosts an application, it promptly boots up from the external flash. The integrated highspeed cache optimizes the system's performance and memory. Also, ESP8266EX can be applied to any micro-controller design as a ...
MCQs - gtbit
... 75. What is asynchronous counter : a) each flip-flop has it own clock b) all the flip-flop are combined to common clock c) both a and b d) none of the above 76. UP Counter is : a) it counts in upward manner b) it count in down ward manner c) it counts in both the direction d) none of the above 77. D ...
... 75. What is asynchronous counter : a) each flip-flop has it own clock b) all the flip-flop are combined to common clock c) both a and b d) none of the above 76. UP Counter is : a) it counts in upward manner b) it count in down ward manner c) it counts in both the direction d) none of the above 77. D ...
Arduino-BOT Lecture #1
... • Verify is used to compile your program The Arduino software is based on C/C++. (or sketch). (It checks for errors). Note that the instructions are case-sensitive. C++ is not line-oriented, so a semicolon (;) is needed • Upload is used to send the program (sketch) to the Arduino-BOT via the to indi ...
... • Verify is used to compile your program The Arduino software is based on C/C++. (or sketch). (It checks for errors). Note that the instructions are case-sensitive. C++ is not line-oriented, so a semicolon (;) is needed • Upload is used to send the program (sketch) to the Arduino-BOT via the to indi ...
Microcontroller
A microcontroller (sometimes abbreviated µC, uC or MCU) is a small computer on a single integrated circuit containing a processor core, memory, and programmable input/output peripherals. Program memory in the form of Ferroelectric RAM, NOR flash or OTP ROM is also often included on chip, as well as a typically small amount of RAM. Microcontrollers are designed for embedded applications, in contrast to the microprocessors used in personal computers or other general purpose applications.Microcontrollers are used in automatically controlled products and devices, such as automobile engine control systems, implantable medical devices, remote controls, office machines, appliances, power tools, toys and other embedded systems. By reducing the size and cost compared to a design that uses a separate microprocessor, memory, and input/output devices, microcontrollers make it economical to digitally control even more devices and processes. Mixed signal microcontrollers are common, integrating analog components needed to control non-digital electronic systems.Some microcontrollers may use four-bit words and operate at clock rate frequencies as low as 4 kHz, for low power consumption (single-digit milliwatts or microwatts). They will generally have the ability to retain functionality while waiting for an event such as a button press or other interrupt; power consumption while sleeping (CPU clock and most peripherals off) may be just nanowatts, making many of them well suited for long lasting battery applications. Other microcontrollers may serve performance-critical roles, where they may need to act more like a digital signal processor (DSP), with higher clock speeds and power consumption.