MAX9386/MAX9387/MAX9388 Differential 5:1 or 4:1 ECL/PECL Multiplexers with Single/Dual Output Buffers General Description
... Current into an I/O pin is defined as positive. Current out of an I/O pin is defined as negative. DC parameters production tested at TA = +25°C and guaranteed by design over the full operating temperature range. Single-ended data input operation using VBB_ is limited to (VCC - VEE) ≥ 3.0V. Use VBB_ ...
... Current into an I/O pin is defined as positive. Current out of an I/O pin is defined as negative. DC parameters production tested at TA = +25°C and guaranteed by design over the full operating temperature range. Single-ended data input operation using VBB_ is limited to (VCC - VEE) ≥ 3.0V. Use VBB_ ...
MICROMASTER 420 0.12 kW - 11 kW Operating Instructions Issue 10/06
... ensure or enforce safe operation, even when a fault occurs (e.g. independent limit switches, mechanical interlocks, etc.). Certain parameter settings may cause the inverter to restart automatically after an input power failure. This equipment is capable of providing internal motor overload protectio ...
... ensure or enforce safe operation, even when a fault occurs (e.g. independent limit switches, mechanical interlocks, etc.). Certain parameter settings may cause the inverter to restart automatically after an input power failure. This equipment is capable of providing internal motor overload protectio ...
Manual - ATB Automation
... § Variable feed-in power using supply modules that can be connected in parallel ...
... § Variable feed-in power using supply modules that can be connected in parallel ...
Axis controller CPX-CMAX-C1-1 Terminal CPX
... injuries. Dangerous movements due to incorrect control of connected actuators, for example caused by: – untidy or faulty wiring/cabling – errors in operating the components – errors in the measured value and signal encoders – defective or non-EMC-compliant components – errors in the higher-order con ...
... injuries. Dangerous movements due to incorrect control of connected actuators, for example caused by: – untidy or faulty wiring/cabling – errors in operating the components – errors in the measured value and signal encoders – defective or non-EMC-compliant components – errors in the higher-order con ...
MN225016EN/ Old S225-11-1
... and ground power distribution equipment. • Is trained in the care and use of protective equipment such as arc flash clothing, safety glasses, face shield, hard hat, rubber gloves, clampstick, hotstick, etc. Following is important safety information. For safe installation and operation of this equip ...
... and ground power distribution equipment. • Is trained in the care and use of protective equipment such as arc flash clothing, safety glasses, face shield, hard hat, rubber gloves, clampstick, hotstick, etc. Following is important safety information. For safe installation and operation of this equip ...
Andrzej M. Trzynadlowski-Control of Induction Motors (Electrical and
... contacts, such as the commutator and brushes in dc machines or slip rings and brushes in ac synchronous motors and generators, are needed. This arrangement greatly increases reliability of induction motors and eliminates the danger of sparking, permitting squirrel-cage machines to be safely used in ...
... contacts, such as the commutator and brushes in dc machines or slip rings and brushes in ac synchronous motors and generators, are needed. This arrangement greatly increases reliability of induction motors and eliminates the danger of sparking, permitting squirrel-cage machines to be safely used in ...
IOSR Journal of Electrical and Electronics Engineering (IOSR-JEEE)
... storage, and electric vehicle drives, where separate dc sources naturally exist[11]-[21]. However, because most current cascade inverters are based on a series connection of several single voltage source inverters (VSI) with two active devices in one leg, they suffer from shoot-through problems, the ...
... storage, and electric vehicle drives, where separate dc sources naturally exist[11]-[21]. However, because most current cascade inverters are based on a series connection of several single voltage source inverters (VSI) with two active devices in one leg, they suffer from shoot-through problems, the ...
COMPARATIVE MODELING, SIMULATION, AND CONTROL OF
... Most rotary blasthole drills used in the mining industry today are equipped with automatic control systems. However, few, if any, implement closed-loop feedback control of the drilling process itself. This thesis investigates the potential for such control on a large rotary electric blasthole drill. ...
... Most rotary blasthole drills used in the mining industry today are equipped with automatic control systems. However, few, if any, implement closed-loop feedback control of the drilling process itself. This thesis investigates the potential for such control on a large rotary electric blasthole drill. ...
submittals for release stand-alone clc systems
... Replacement hardware shall be re-installed by licensed Electrical Contractor only. ...
... Replacement hardware shall be re-installed by licensed Electrical Contractor only. ...
ELECTRONICS LABORATORY
... Guided Practices, Self-evaluation (exam), Video and Statistical analysis. Notes: 1) Multipost option: This module is for 10 students post, but we can recommend the number of units for 20 or 30 students working simultaneously. 2)Supply conditions included: a) Technical conditions: - Laboratories adap ...
... Guided Practices, Self-evaluation (exam), Video and Statistical analysis. Notes: 1) Multipost option: This module is for 10 students post, but we can recommend the number of units for 20 or 30 students working simultaneously. 2)Supply conditions included: a) Technical conditions: - Laboratories adap ...
+5V-Powered, Multichannel RS-232 Drivers/Receivers General Description Next-Generation Device Features
... ROUT........................................................-0.3V to (VCC + 0.3V) Short-Circuit Duration, TOUT to GND ........................Continuous Continuous Power Dissipation (TA = +70°C) 14-Pin Plastic DIP (derate 10.00mW/°C above +70°C)....800mW 16-Pin Plastic DIP (derate 10.53mW/°C above + ...
... ROUT........................................................-0.3V to (VCC + 0.3V) Short-Circuit Duration, TOUT to GND ........................Continuous Continuous Power Dissipation (TA = +70°C) 14-Pin Plastic DIP (derate 10.00mW/°C above +70°C)....800mW 16-Pin Plastic DIP (derate 10.53mW/°C above + ...
Control theory
Control theory is an interdisciplinary branch of engineering and mathematics that deals with the behavior of dynamical systems with inputs, and how their behavior is modified by feedback. The usual objective of control theory is to control a system, often called the plant, so its output follows a desired control signal, called the reference, which may be a fixed or changing value. To do this a controller is designed, which monitors the output and compares it with the reference. The difference between actual and desired output, called the error signal, is applied as feedback to the input of the system, to bring the actual output closer to the reference. Some topics studied in control theory are stability (whether the output will converge to the reference value or oscillate about it), controllability and observability.Extensive use is usually made of a diagrammatic style known as the block diagram. The transfer function, also known as the system function or network function, is a mathematical representation of the relation between the input and output based on the differential equations describing the system.Although a major application of control theory is in control systems engineering, which deals with the design of process control systems for industry, other applications range far beyond this. As the general theory of feedback systems, control theory is useful wherever feedback occurs. A few examples are in physiology, electronics, climate modeling, machine design, ecosystems, navigation, neural networks, predator-prey interaction, gene expression, and production theory.