LT5526 - High Linearity, Low Power Downconverting Mixer.
... bias/enable circuits. The IC has been optimized for downconverter applications with RF input signals to 2GHz and LO signals to 2.5GHz. With proper matching, the IF output can be tuned for operation at frequencies from 0.1MHz to 1GHz. Operation over a wider input frequency range is possible, though w ...
... bias/enable circuits. The IC has been optimized for downconverter applications with RF input signals to 2GHz and LO signals to 2.5GHz. With proper matching, the IF output can be tuned for operation at frequencies from 0.1MHz to 1GHz. Operation over a wider input frequency range is possible, though w ...
(t) i - inst.eecs.berkeley.edu
... element (expressed as a phasor) and the current through the element (expressed as a phasor). Impedance is a complex number. Impedance depends on frequency. Phasors and complex impedance allow us to use Ohm’s law with complex numbers to compute current from voltage and voltage from current. ...
... element (expressed as a phasor) and the current through the element (expressed as a phasor). Impedance is a complex number. Impedance depends on frequency. Phasors and complex impedance allow us to use Ohm’s law with complex numbers to compute current from voltage and voltage from current. ...
Dual, Low-Power, High-Speed, Fixed
... This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete devi ...
... This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete devi ...
IF 1308 Revision 4
... cell is important. The photo-sensitive window should preferably be aimed facing north where the change in light intensity is relatively uniform. Rows of trees, close buildings and overhangs may affect the turn off levels of the photocell. If the cell is located near other light sources, the controll ...
... cell is important. The photo-sensitive window should preferably be aimed facing north where the change in light intensity is relatively uniform. Rows of trees, close buildings and overhangs may affect the turn off levels of the photocell. If the cell is located near other light sources, the controll ...
A Guide to the Design of Laminate PCBs at Microwave
... The copper tracks are generally covered so as to stop corrosion and/or oxidation. The covering generally takes the form of ENIG (Electroless Nickel Immersion Gold) for low frequency circuits where the loss due to the Nickel barrier layer is not such an issue. However, at higher frequencies the prese ...
... The copper tracks are generally covered so as to stop corrosion and/or oxidation. The covering generally takes the form of ENIG (Electroless Nickel Immersion Gold) for low frequency circuits where the loss due to the Nickel barrier layer is not such an issue. However, at higher frequencies the prese ...
Comparing Theory and Measurements of Woodwind
... This thesis provides a review of a computational modeling technique for woodwindlike musical instruments with arbitrarily shaped bore and finger holes. The model of a simple acoustic structure implemented in Matlab is verified through experimental measurements in terms of radiation directivity. The ...
... This thesis provides a review of a computational modeling technique for woodwindlike musical instruments with arbitrarily shaped bore and finger holes. The model of a simple acoustic structure implemented in Matlab is verified through experimental measurements in terms of radiation directivity. The ...
Full Text:PDF
... is typically comprised of a noise source, EMI antenna, and a parasitic coupling path between the noise source and EMI antenna. The increased impedance of a finite reference (ground) plane in a printed circuit board (PCB) results in a currentdriven noise source, which may drive the EMI antenna [1], [2 ...
... is typically comprised of a noise source, EMI antenna, and a parasitic coupling path between the noise source and EMI antenna. The increased impedance of a finite reference (ground) plane in a printed circuit board (PCB) results in a currentdriven noise source, which may drive the EMI antenna [1], [2 ...
Electroacoustic modelling of the subwoofer enclosures
... it generates a volume velocity SD u. Due to air load and possible loading from the box where the driver is mounted, this creates a counterforce SD pD , which in turn resists movement of the diaphragm. This is seen as reduction in the driver electrical impedance. ZAB is the acoustic load impedance of ...
... it generates a volume velocity SD u. Due to air load and possible loading from the box where the driver is mounted, this creates a counterforce SD pD , which in turn resists movement of the diaphragm. This is seen as reduction in the driver electrical impedance. ZAB is the acoustic load impedance of ...
Equivalent Circuit of Repeater Antenna for - Hori
... few years; however, another problem emerges related to charging ...
... few years; however, another problem emerges related to charging ...
Standing wave ratio
In radio engineering and telecommunications, standing wave ratio (SWR) is a measure of impedance matching of loads to the characteristic impedance of a transmission line or waveguide. Impedance mismatches result in standing waves along the transmission line, and SWR is defined as the ratio of the partial standing wave's amplitude at an antinode (maximum) to the amplitude at a node (minimum) along the line.The SWR is usually thought of in terms of the maximum and minimum AC voltages along the transmission line, thus called the voltage standing wave ratio or VSWR (sometimes pronounced ""viswar""). For example, the VSWR value 1.2:1 denotes an AC voltage due to standing waves along the transmission line reaching a peak value 1.2 times that of the minimum AC voltage along that line. The SWR can as well be defined as the ratio of the maximum amplitude to minimum amplitude of the transmission line's currents, electric field strength, or the magnetic field strength. Neglecting transmission line loss, these ratios are identical.The power standing wave ratio (PSWR) is defined as the square of the VSWR, however this terminology has no physical relation to actual powers involved in transmission.The SWR can be measured with an instrument called an SWR meter. Since SWR is defined relative to the transmission line's characteristic impedance, the SWR meter must be constructed for that impedance; in practice most transmission lines used in these applications are coaxial cables with an impedance of either 50 or 75 ohms. Checking the SWR is a standard procedure in a radio station, for instance, to verify impedance matching of the antenna to the transmission line (and transmitter). Unlike connecting an impedance analyzer (or ""impedance bridge"") directly to the antenna (or other load), the SWR does not measure the actual impedance of the load, but quantifies the magnitude of the impedance mismatch just performing a measurement on the transmitter side of the transmission line.