CN-0111
... This circuit shown in Figure 1 provides a low cost, high voltage unipolar DAC using the AD5292 digital potentiometer in conjunction with the dual ADA4091-2 op amp and ADR512 voltage reference. This circuit offers 10-bit resolution over an output voltage range of 0 V to 30 V and is capable of deliver ...
... This circuit shown in Figure 1 provides a low cost, high voltage unipolar DAC using the AD5292 digital potentiometer in conjunction with the dual ADA4091-2 op amp and ADR512 voltage reference. This circuit offers 10-bit resolution over an output voltage range of 0 V to 30 V and is capable of deliver ...
CIRCUIT FUNCTION AND BENEFITS
... the correct VAPD for the conditions. Note that all connections to the ADL5317 are not shown for clarity. In this application, the ADL5317 operates in linear mode. The bias voltage to the APD, delivered at the VAPD pin, is controlled by the voltage (VSET) at the VSET pin. The bias voltage at VAPD is ...
... the correct VAPD for the conditions. Note that all connections to the ADL5317 are not shown for clarity. In this application, the ADL5317 operates in linear mode. The bias voltage to the APD, delivered at the VAPD pin, is controlled by the voltage (VSET) at the VSET pin. The bias voltage at VAPD is ...
MDS-065APS24 B Datasheet
... Temperature Protection (OTP). This is activated when the overload condition persists for an extended duration and the output current is below the overload trigger point but >100% load. In the event of a higher operating condition at 100% load, the power supply will run into OTP when the surrounding ...
... Temperature Protection (OTP). This is activated when the overload condition persists for an extended duration and the output current is below the overload trigger point but >100% load. In the event of a higher operating condition at 100% load, the power supply will run into OTP when the surrounding ...
op-amp parameters
... Common-Mode Rejection Ratio (CMRR) CMRR is the measure for how well it rejects an unwanted the signal. It is the ratio of open loop gain (Aol) to common-mode gain (Acm). The open loop gain is a data sheet value. ...
... Common-Mode Rejection Ratio (CMRR) CMRR is the measure for how well it rejects an unwanted the signal. It is the ratio of open loop gain (Aol) to common-mode gain (Acm). The open loop gain is a data sheet value. ...
Controlling Lights & Fans with TV remote
... Now a days many(old people, physically disabled….) are facing problem to directly go and switch on the lights and fans in their home. So there is a need for such type of remote controllable circuit. ...
... Now a days many(old people, physically disabled….) are facing problem to directly go and switch on the lights and fans in their home. So there is a need for such type of remote controllable circuit. ...
TAT7467H 数据资料DataSheet下载
... The amplifier of the TAT7467H was specially designed to work with on-chip linearization to provide 3rd order distortion improvement over a wide range of RF power levels and across the full CATV bandwidth. Operation of the linearizer will not affect overall gain by more than 0.7 dB. For any amplifier ...
... The amplifier of the TAT7467H was specially designed to work with on-chip linearization to provide 3rd order distortion improvement over a wide range of RF power levels and across the full CATV bandwidth. Operation of the linearizer will not affect overall gain by more than 0.7 dB. For any amplifier ...
Lab E3
... 2) to determine the resistance of a light bulb and of a resistor, and 3) to determine if the light bulb and resistor obey Ohm’s Rule. The definition of the resistance of a material is: R = V/I where V is the voltage difference between two ends of the material and I is the current that the voltage ...
... 2) to determine the resistance of a light bulb and of a resistor, and 3) to determine if the light bulb and resistor obey Ohm’s Rule. The definition of the resistance of a material is: R = V/I where V is the voltage difference between two ends of the material and I is the current that the voltage ...
Audio power amplifiers
... Single ended output amplifier A simple amplifier can be constructed using only a few external components (Pout = 2W VCC = 20V) as shown in Figure 1. The input may be from crystal or ceramic pick-ups, cartridge or microphone, or may be from the LM381. Bridge amplifier For an increase in output, two a ...
... Single ended output amplifier A simple amplifier can be constructed using only a few external components (Pout = 2W VCC = 20V) as shown in Figure 1. The input may be from crystal or ceramic pick-ups, cartridge or microphone, or may be from the LM381. Bridge amplifier For an increase in output, two a ...
The uA741 Operational Amplifier
... Q13B, and the resistors R8 and R9. Transistor Q16 acts as an emitter follower giving the second stage a high input resistance. Transistor Q17 is a common-emitter amplifier with a 100-Ώ resistor in the emitter. The load of this amplifier is composed of the output resistance of Q13B. This use of a tra ...
... Q13B, and the resistors R8 and R9. Transistor Q16 acts as an emitter follower giving the second stage a high input resistance. Transistor Q17 is a common-emitter amplifier with a 100-Ώ resistor in the emitter. The load of this amplifier is composed of the output resistance of Q13B. This use of a tra ...
Model 430 Bridgesensor
... The supply has provisions for remote sensing when the excitation lines may have significant resistance compared to the sensor. The +SENSE and -SENSE terminals must be connected to the B+ and B- terminals respectively, i.e. connect terminals 1 and 2 together, and connect terminals 3 and 4 together wh ...
... The supply has provisions for remote sensing when the excitation lines may have significant resistance compared to the sensor. The +SENSE and -SENSE terminals must be connected to the B+ and B- terminals respectively, i.e. connect terminals 1 and 2 together, and connect terminals 3 and 4 together wh ...
MAT04 Data Sheet
... The circuit of Figure 6 is a very low noise, high speed amplifier, ideal for use in precision transducer and professional audio applications. The performance of the amplifier is summarized in Table I. Figure 7 shows the input referred spot noise over the 0–25 kHz bandwidth to be flat at 1.2 nV/√Hz. ...
... The circuit of Figure 6 is a very low noise, high speed amplifier, ideal for use in precision transducer and professional audio applications. The performance of the amplifier is summarized in Table I. Figure 7 shows the input referred spot noise over the 0–25 kHz bandwidth to be flat at 1.2 nV/√Hz. ...
AD8629S: Zero-Drift, Single-Supply Rail-to-Rail Input/Output Operational Amplifier Aerospace Data Sheet (Rev E, 10/2012)
... Previous designs used either auto-zeroing or chopping to add precision to the specifications of an amplifier. Auto-zeroing results in low noise energy at the auto-zeroing frequency, at the expense of higher low frequency noise due to aliasing of wideband noise into the auto-zeroed frequency band. Ch ...
... Previous designs used either auto-zeroing or chopping to add precision to the specifications of an amplifier. Auto-zeroing results in low noise energy at the auto-zeroing frequency, at the expense of higher low frequency noise due to aliasing of wideband noise into the auto-zeroed frequency band. Ch ...