ISSCC 2017 Digest of Technical Papers
... parasitic capacitors. Figure 16.1.3b shows the topology of the RA. While an open-loop integrator-type amplifier avoids the challenges associated with stability and settling, it does have stringent linearity requirements. A folded-cascode OTA is used to minimize the supply voltage. A linearized input ...
... parasitic capacitors. Figure 16.1.3b shows the topology of the RA. While an open-loop integrator-type amplifier avoids the challenges associated with stability and settling, it does have stringent linearity requirements. A folded-cascode OTA is used to minimize the supply voltage. A linearized input ...
A 3–10-GHz Low-Noise Amplifier With Wideband LC
... limited because of packaging considerations. For a wirebond package, the minimum degeneration inductance even in the case of multiple parallel downbonds cannot be lower than around 0.5 nH because of mutual inductance. At first sight, (5) would limit to obtain a 50- input resistance the maximum allow ...
... limited because of packaging considerations. For a wirebond package, the minimum degeneration inductance even in the case of multiple parallel downbonds cannot be lower than around 0.5 nH because of mutual inductance. At first sight, (5) would limit to obtain a 50- input resistance the maximum allow ...
installer`s reference xtant technologies
... and Amp Vert. Acc. Port. The fifth port is dedicated to the RCA line outputs and is labeled Line Out Vert. Acc. Port. Xtant offers two types of accessory modules which are designed for either “Horizontal” or “Vertical” mounting. The docking port, located behind the RCA line outputs, labeled Amp Vert ...
... and Amp Vert. Acc. Port. The fifth port is dedicated to the RCA line outputs and is labeled Line Out Vert. Acc. Port. Xtant offers two types of accessory modules which are designed for either “Horizontal” or “Vertical” mounting. The docking port, located behind the RCA line outputs, labeled Amp Vert ...
High-Speed and High-Precision Current Winner-Take
... currents—(simulated)] in case when a very small difference between two input currents is applied (30 nA for high currents and 1.8 nA for subthreshold applications). These circuit performances are the direct result from very strong feedbacks applied in the circuit, causing however, higher power dissi ...
... currents—(simulated)] in case when a very small difference between two input currents is applied (30 nA for high currents and 1.8 nA for subthreshold applications). These circuit performances are the direct result from very strong feedbacks applied in the circuit, causing however, higher power dissi ...
www.BDTIC.com/ADI
... provides maximum noise immunity. This feature is made possible by the large input swing capability, 2 µA logic input current and completely adjustable logic threshold voltage. For V– = –15 V, the logic inputs may swing between –5 and +18 V. This enables direct interface with +15 V CMOS logic, even w ...
... provides maximum noise immunity. This feature is made possible by the large input swing capability, 2 µA logic input current and completely adjustable logic threshold voltage. For V– = –15 V, the logic inputs may swing between –5 and +18 V. This enables direct interface with +15 V CMOS logic, even w ...
ICL7660, ICL7660A CMOS Voltage Converters Features FN3072.7
... In the ICL7660 and ICL7660A, the 4 switches of Figure 12 are MOS power switches; S1 is a P-Channel device and S2 , S3 and S4 are N-Channel devices. The main difficulty with this approach is that in integrating the switches, the substrates of S3 and S4 must always remain reverse biased with respect t ...
... In the ICL7660 and ICL7660A, the 4 switches of Figure 12 are MOS power switches; S1 is a P-Channel device and S2 , S3 and S4 are N-Channel devices. The main difficulty with this approach is that in integrating the switches, the substrates of S3 and S4 must always remain reverse biased with respect t ...
Application Note 1724 LM5015 Isolated Two-Switch DC
... to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and t ...
... to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and t ...
FEATURES FUNCTIONAL BLOCK DIAGRAM
... voltage at code 0x000 as predicted by the line formed from the output voltages at code 0x040 (2% FS) and code 0xFFF (100% FS). Ideally, the offset error should be 0 V. Offset error occurs from a combination of the offset voltage of the amplifier and offset errors in the DAC. It is expressed in LSBs. ...
... voltage at code 0x000 as predicted by the line formed from the output voltages at code 0x040 (2% FS) and code 0xFFF (100% FS). Ideally, the offset error should be 0 V. Offset error occurs from a combination of the offset voltage of the amplifier and offset errors in the DAC. It is expressed in LSBs. ...
araştirma makalesi̇
... last 10 years. It has an insulated gate input like that of power MOSFET, while benefiting low onstate resistance of a power bipolar transistor. Also, it is known that the IGBT functions as a bipolar transistor, when its base current is supplied by the drain of a MOSFET which has its source short cir ...
... last 10 years. It has an insulated gate input like that of power MOSFET, while benefiting low onstate resistance of a power bipolar transistor. Also, it is known that the IGBT functions as a bipolar transistor, when its base current is supplied by the drain of a MOSFET which has its source short cir ...
LM1084 5A Low Dropout Positive Regulators
... used at the ADJ pin to increase ripple rejection. If this is done the output capacitor should be increased to 22uF for tantalums or to 150uF for aluminum. Capacitors other than tantalum or aluminum can be used at the adjust pin and the input pin. A 10uF capacitor is a reasonable value at the input. ...
... used at the ADJ pin to increase ripple rejection. If this is done the output capacitor should be increased to 22uF for tantalums or to 150uF for aluminum. Capacitors other than tantalum or aluminum can be used at the adjust pin and the input pin. A 10uF capacitor is a reasonable value at the input. ...
Novel circuits for neural information processing
... selectively respond to an edge and the second class responds to bar width. There are two schools of thought over the function of the visual cortical neurons. Some researchers believe that the visual cortical neurons act as feature detectors [3], while others believe that cortical neurons act as spat ...
... selectively respond to an edge and the second class responds to bar width. There are two schools of thought over the function of the visual cortical neurons. Some researchers believe that the visual cortical neurons act as feature detectors [3], while others believe that cortical neurons act as spat ...