ADN4667 数据手册DataSheet 下载
... Active High Enable and Power-Down Input (3 V TTL/CMOS). If EN is held low or open circuit, EN enables the drivers when high and disables the drivers when low. Driver Channel 1 Logic Input. Driver Channel 2 Logic Input. Power Supply Input. These parts can be operated from 3.0 V to 3.6 V. The supply s ...
... Active High Enable and Power-Down Input (3 V TTL/CMOS). If EN is held low or open circuit, EN enables the drivers when high and disables the drivers when low. Driver Channel 1 Logic Input. Driver Channel 2 Logic Input. Power Supply Input. These parts can be operated from 3.0 V to 3.6 V. The supply s ...
Phase Control Using Thyristors
... Many circuits begin each half-cycle with the capacitor voltage at or near zero. However, most circuits leave a relatively large residual voltage on the capacitor after discharge. Therefore, the charging resistor must be determined on the basis of additional charge necessary to raise the capacitor to ...
... Many circuits begin each half-cycle with the capacitor voltage at or near zero. However, most circuits leave a relatively large residual voltage on the capacitor after discharge. Therefore, the charging resistor must be determined on the basis of additional charge necessary to raise the capacitor to ...
MAX17062 TFT-LCD Step-Up DC-DC Converter General Description Features
... the inductor. These factors influence the converter’s efficiency, maximum output load capability, transientresponse time, and output-voltage ripple. Physical size and cost are also important factors to be considered. The maximum output current, input voltage, output voltage, and switching frequency ...
... the inductor. These factors influence the converter’s efficiency, maximum output load capability, transientresponse time, and output-voltage ripple. Physical size and cost are also important factors to be considered. The maximum output current, input voltage, output voltage, and switching frequency ...
a 380 MHz, 25 mA, Triple 2:1 Multiplexers AD8183/AD8185
... 380 MHz, along with slew rate of 1000 V/µs. With better than –90 dB of channel-to-channel crosstalk and isolation at 10 MHz, they are useful in many high-speed applications. The differential gain and differential phase errors of 0.01% and 0.02° respectively, along with 0.1 dB flatness to 90 MHz make ...
... 380 MHz, along with slew rate of 1000 V/µs. With better than –90 dB of channel-to-channel crosstalk and isolation at 10 MHz, they are useful in many high-speed applications. The differential gain and differential phase errors of 0.01% and 0.02° respectively, along with 0.1 dB flatness to 90 MHz make ...
A MODEL OF VOLTAGE IN A RESISTOR CIRCUIT AND AN RC
... used Kirchhoff’s second law to solve a system of differential equations, obtaining Equation 3.13 (V = V0 exp(−t/RC)). This equation shows that voltage decays exponentially. 2.1. Importance of Problem. These mathematical models are important to consider because they allow us to construct electrical d ...
... used Kirchhoff’s second law to solve a system of differential equations, obtaining Equation 3.13 (V = V0 exp(−t/RC)). This equation shows that voltage decays exponentially. 2.1. Importance of Problem. These mathematical models are important to consider because they allow us to construct electrical d ...
AN3257
... The architecture is based on a two-stage approach: a front-end PFC pre-regulator and a downstream multi-resonant half bridge converter. Both stages are controlled by the new IC L6585DE- which integrates PFC and half bridge control circuits and the relevant drivers. Although this new device is dedica ...
... The architecture is based on a two-stage approach: a front-end PFC pre-regulator and a downstream multi-resonant half bridge converter. Both stages are controlled by the new IC L6585DE- which integrates PFC and half bridge control circuits and the relevant drivers. Although this new device is dedica ...
NCL30081LEDGEVB 3.6 W Flyback 3 LED Step Dimmable Driver Evaluation Board User's Manual
... resistor will also have some effect on the output current. Since the input power is < 5 W maximum, this falls below the level where power factor or harmonic current requirements are applicable in many countries (e.g. US). In the EU, the harmonic current requirements for IEC61000-3-2 Class C are appl ...
... resistor will also have some effect on the output current. Since the input power is < 5 W maximum, this falls below the level where power factor or harmonic current requirements are applicable in many countries (e.g. US). In the EU, the harmonic current requirements for IEC61000-3-2 Class C are appl ...
AD8067
... the total drive power is VS/2 × IOUT, some of which is dissipated in the package and some in the load (VOUT × IOUT). The difference between the total drive power and the load power is the drive power dissipated in the package. RMS output voltages should be considered. ...
... the total drive power is VS/2 × IOUT, some of which is dissipated in the package and some in the load (VOUT × IOUT). The difference between the total drive power and the load power is the drive power dissipated in the package. RMS output voltages should be considered. ...
NCP3065, NCV3065 Up to 1.5 A Constant Current Switching Regulator for LEDs
... Darlington Output Switch is disabled. The temperature sensing circuit is designed with some hysteresis. The Darlington Switch is enabled again when the chip temperature decreases under the low threshold. This feature is provided to prevent catastrophic failures from accidental device overheating. It ...
... Darlington Output Switch is disabled. The temperature sensing circuit is designed with some hysteresis. The Darlington Switch is enabled again when the chip temperature decreases under the low threshold. This feature is provided to prevent catastrophic failures from accidental device overheating. It ...
Hardware Design for Realization of Smart Sensor Network
... deformation of the crystal a polarization will occur and a surface charge will be induced on the crystal. The charge can then be transferred to capacitor plates giving rise to free charge separated by a distance, thus creating a voltage source. A major difficulty with this particular capacitive sour ...
... deformation of the crystal a polarization will occur and a surface charge will be induced on the crystal. The charge can then be transferred to capacitor plates giving rise to free charge separated by a distance, thus creating a voltage source. A major difficulty with this particular capacitive sour ...
TPA2000D1-Q1 数据资料 dataSheet 下载
... improved efficiency and SNR. It also allows the device to be connected directly to the speaker without the use of the LC output filter commonly associated with class-D amplifiers (this results in EMI which must be shielded at the system level). These features make the device ideal for use in devices ...
... improved efficiency and SNR. It also allows the device to be connected directly to the speaker without the use of the LC output filter commonly associated with class-D amplifiers (this results in EMI which must be shielded at the system level). These features make the device ideal for use in devices ...