MAX9210/MAX9214/MAX9220/MAX9222 Programmable DC-Balance 21-Bit Deserializers General Description
... the voltage rating of the capacitor. The typical LVDS driver output is 350mV centered on an offset voltage of 1.25V, making single-ended output voltages of 1.425V and 1.075V. An LVDS receiver accepts signals from 0 to 2.4V, allowing approximately ±1V common-mode difference between the driver and rec ...
... the voltage rating of the capacitor. The typical LVDS driver output is 350mV centered on an offset voltage of 1.25V, making single-ended output voltages of 1.425V and 1.075V. An LVDS receiver accepts signals from 0 to 2.4V, allowing approximately ±1V common-mode difference between the driver and rec ...
Ohmic Drop: Part 2
... therefore the ohmic drop must be measured experimentally. The three most common methods for measuring ohmic drop are: ...
... therefore the ohmic drop must be measured experimentally. The three most common methods for measuring ohmic drop are: ...
MAX7327 I C Port Expander with 12 Push-Pull Outputs and 4 Open-Drain I/Os
... A latching interrupt output INT automatically flags data changes on any of the I/O ports used as inputs through an interrupt mask register. Data changes on any input port forces INT to a logic-low. The interrupt output INT is deasserted when the MAX7327 is next accessed through the serial interface. ...
... A latching interrupt output INT automatically flags data changes on any of the I/O ports used as inputs through an interrupt mask register. Data changes on any input port forces INT to a logic-low. The interrupt output INT is deasserted when the MAX7327 is next accessed through the serial interface. ...
Infinite electrical networks: a reprise
... NCE UPON A TIME, an electrical engineer set out to logr, where r is the radial distance from the point of to discover the value of the driving-point resistance R current injection. Now, I’ve got some bad news for you,” between two adjacent nodes a and b in an infinite resistive continued the mathema ...
... NCE UPON A TIME, an electrical engineer set out to logr, where r is the radial distance from the point of to discover the value of the driving-point resistance R current injection. Now, I’ve got some bad news for you,” between two adjacent nodes a and b in an infinite resistive continued the mathema ...
RESISTORS AND TYPES OF RESISTORS
... material such as constantan (60% copper and 40% nickel) and manganin which have high resistivities and low temperature coefficients are employed. The completed wire wound resistor is coated with an insulating material such as baked enamel. c) Metalized resistors It is constructed using film depositi ...
... material such as constantan (60% copper and 40% nickel) and manganin which have high resistivities and low temperature coefficients are employed. The completed wire wound resistor is coated with an insulating material such as baked enamel. c) Metalized resistors It is constructed using film depositi ...
OPA2695
... intermediate frequency (IF) amplifier. The device has been optimized for high gain operation, and the pin outs of the two available packages (QFN-16, SO-8) have been optimized to provide symmetrical input and output paths. This architecture makes the OPA2695 an ideal choice as a differential driver, ...
... intermediate frequency (IF) amplifier. The device has been optimized for high gain operation, and the pin outs of the two available packages (QFN-16, SO-8) have been optimized to provide symmetrical input and output paths. This architecture makes the OPA2695 an ideal choice as a differential driver, ...
FEATURES APPLICATIONS D
... This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete devi ...
... This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete devi ...
