DS1110L 3V 10-Tap Silicon Delay Line General Description Features
... Figure 3 illustrates the hardware configuration used for measuring the timing parameters on the DS1110L. A precision pulse generator under software control produces the input waveform. Time delays are measured by a time interval counter (20ps resolution) connected ...
... Figure 3 illustrates the hardware configuration used for measuring the timing parameters on the DS1110L. A precision pulse generator under software control produces the input waveform. Time delays are measured by a time interval counter (20ps resolution) connected ...
Experiment 2
... 7. Adjust the power supply to produce ¾, ½ and ¼ scale deflections and record the current for both meters at each of these values in Table 1. 8. Calculate the percentage error at each of the four currents. Part 3- Voltmeter Circuit A voltmeter is an instrument that is used to measure the voltage th ...
... 7. Adjust the power supply to produce ¾, ½ and ¼ scale deflections and record the current for both meters at each of these values in Table 1. 8. Calculate the percentage error at each of the four currents. Part 3- Voltmeter Circuit A voltmeter is an instrument that is used to measure the voltage th ...
AD8137 (Rev. E)
... and Figure 58; Renumbered Sequentially ......................................7 Changes to Figure 32...................................................................... 12 Changes to Figure 40...................................................................... 13 Changes to Figure 55............. ...
... and Figure 58; Renumbered Sequentially ......................................7 Changes to Figure 32...................................................................... 12 Changes to Figure 40...................................................................... 13 Changes to Figure 55............. ...
AC Circuit Analysis 2
... Instead of first deriving the differential equation and then transforming it into phasor to solve for Vo, we can transform all the RLC components into phasor first, then apply the KCL laws and other theorems to set up a phasor equation involving Vo directly. ...
... Instead of first deriving the differential equation and then transforming it into phasor to solve for Vo, we can transform all the RLC components into phasor first, then apply the KCL laws and other theorems to set up a phasor equation involving Vo directly. ...
MAX2021EVKIT.pdf
... basic functionality of the EV kit as an upconverter. As a general precaution to prevent damaging the outputs by driving high VSWR loads, do not turn on DC power or RF signal generators until all connections are made. This upconverter procedure is general to operation with an I/Q baseband input signa ...
... basic functionality of the EV kit as an upconverter. As a general precaution to prevent damaging the outputs by driving high VSWR loads, do not turn on DC power or RF signal generators until all connections are made. This upconverter procedure is general to operation with an I/Q baseband input signa ...
Evaluation Board User Guide UG-056
... of the various ADP124 and ADP125 evaluation board configurations. Table 1 describes the components. ...
... of the various ADP124 and ADP125 evaluation board configurations. Table 1 describes the components. ...
MAX5174/MAX5176 General Description Features
... The MAX5174/MAX5176 low-power, serial, voltage-output, 12-bit digital-to-analog converters (DACs) feature a precision output amplifier in a space-saving 16-pin QSOP package. The MAX5174 operates from a single +5V supply, and the MAX5176 operates from a single +3V supply. Both devices draw only 280µA ...
... The MAX5174/MAX5176 low-power, serial, voltage-output, 12-bit digital-to-analog converters (DACs) feature a precision output amplifier in a space-saving 16-pin QSOP package. The MAX5174 operates from a single +5V supply, and the MAX5176 operates from a single +3V supply. Both devices draw only 280µA ...
STM6710
... If a monitored supply voltage input falls below the minimum voltage threshold, a single active low output is asserted, triggering a system reset. This device can be configured to support an external manual reset input using minimal external components. Monitoring up to four different voltages in a s ...
... If a monitored supply voltage input falls below the minimum voltage threshold, a single active low output is asserted, triggering a system reset. This device can be configured to support an external manual reset input using minimal external components. Monitoring up to four different voltages in a s ...
TOP Design Study - DCC - LIGO Document Control Center Portal
... Achieving the required dynamic range requires a high current driver chip, as a continuous current of +/- 200mA is required. As switched mode operation is not suitable, the power dissipation of the output devices will be considerable. As noise is temperature dependant, the choice was made to limit te ...
... Achieving the required dynamic range requires a high current driver chip, as a continuous current of +/- 200mA is required. As switched mode operation is not suitable, the power dissipation of the output devices will be considerable. As noise is temperature dependant, the choice was made to limit te ...
MAX1875/MAX1876 Dual 180° Out-of-Phase PWM Step- Down Controllers with POR General Description
... The MAX1875/MAX1876 dual, synchronized, step-down controller generates two outputs from input supplies ranging from 4.75V to 23V. Each output is adjustable from sub-1V to 18V and supports loads of 10A or higher. Input voltage ripple and total RMS input ripple current are reduced by synchronized 180° ...
... The MAX1875/MAX1876 dual, synchronized, step-down controller generates two outputs from input supplies ranging from 4.75V to 23V. Each output is adjustable from sub-1V to 18V and supports loads of 10A or higher. Input voltage ripple and total RMS input ripple current are reduced by synchronized 180° ...
Polytechnic Instrumentation Engineering 2 Year Syllabus
... theorem, De' Morgan's theorem, Simplification of Boolean expressions, Verification of Boolean expressions using truth table Unit III Minimization Techniques (K-Mapping): Representation of Boolean expression - min. and max. term SOP, POS, Conversion of truth tables in POS and SOP form, Karnaugh map ...
... theorem, De' Morgan's theorem, Simplification of Boolean expressions, Verification of Boolean expressions using truth table Unit III Minimization Techniques (K-Mapping): Representation of Boolean expression - min. and max. term SOP, POS, Conversion of truth tables in POS and SOP form, Karnaugh map ...
LT5570 - Linear Technology
... OUT (Pin 6): DC Output Pin. The output impedance is mainly determined by an internal 100Ω series resistance that provides output circuit protection if the output is shorted to ground. DNC (Pins 7, 8): Do Not Connect. Don’t connect any external component at these pins. Avoid a long wire or metal trac ...
... OUT (Pin 6): DC Output Pin. The output impedance is mainly determined by an internal 100Ω series resistance that provides output circuit protection if the output is shorted to ground. DNC (Pins 7, 8): Do Not Connect. Don’t connect any external component at these pins. Avoid a long wire or metal trac ...
DC Voltmeters and Ammeters
... Voltmeters are connected in parallel with whatever device's voltage is to be measured. A parallel connection is used because objects in parallel experience the same potential dierence. (See Figure 2, where the voltmeter is represented by the symbol V.) Ammeters are connected in series with whatever ...
... Voltmeters are connected in parallel with whatever device's voltage is to be measured. A parallel connection is used because objects in parallel experience the same potential dierence. (See Figure 2, where the voltmeter is represented by the symbol V.) Ammeters are connected in series with whatever ...