LT6600-5
... Figure 5 is a laboratory setup that can be used to characterize the LT6600-5 using single-ended instruments with 50Ω source impedance and 50Ω input impedance. For a unity gain configuration the LT6600-5 requires a 806Ω source resistance yet the network analyzer output is calibrated for a 50Ω load res ...
... Figure 5 is a laboratory setup that can be used to characterize the LT6600-5 using single-ended instruments with 50Ω source impedance and 50Ω input impedance. For a unity gain configuration the LT6600-5 requires a 806Ω source resistance yet the network analyzer output is calibrated for a 50Ω load res ...
MAX3748 Compact 155Mbps to 4.25Gbps Limiting Amplifier General Description
... +25°C, VCC = 3.3V, unless otherwise specified. The data input transition time is controlled by a 4th-order Bessel filter with f-3dB = 0.75 ✕ 2.667GHz for all data rates of 2.667Gbps and below, and with f-3dB = 0.75 ✕ data rate for data rates > 3.2Gbps.) Note 4: 223 - 1 PRBS pattern was substituted b ...
... +25°C, VCC = 3.3V, unless otherwise specified. The data input transition time is controlled by a 4th-order Bessel filter with f-3dB = 0.75 ✕ 2.667GHz for all data rates of 2.667Gbps and below, and with f-3dB = 0.75 ✕ data rate for data rates > 3.2Gbps.) Note 4: 223 - 1 PRBS pattern was substituted b ...
300-mA, Sub-Bandgap Output Voltage, Low-Iq, Low
... The TLV712xx series of low-dropout linear regulators (LDOs) are low quiescent current devices with excellent line and load transient performance. These devices provide sub-bandgap output voltages; that is, output voltages less than 1.2 V all the way down to 0.7 V. Therefore, these LDOs can be used t ...
... The TLV712xx series of low-dropout linear regulators (LDOs) are low quiescent current devices with excellent line and load transient performance. These devices provide sub-bandgap output voltages; that is, output voltages less than 1.2 V all the way down to 0.7 V. Therefore, these LDOs can be used t ...
ADG1311 数据手册DataSheet下载
... The ADG1311/ADG1312/ADG1313 contain four independent single-pole/single-throw (SPST) switches. The ADG1311 and ADG1312 differ only in that the digital control logic is inverted. The ADG1311 switches are turned on with Logic 0 on the appropriate control input, while Logic 1 is required for the ADG131 ...
... The ADG1311/ADG1312/ADG1313 contain four independent single-pole/single-throw (SPST) switches. The ADG1311 and ADG1312 differ only in that the digital control logic is inverted. The ADG1311 switches are turned on with Logic 0 on the appropriate control input, while Logic 1 is required for the ADG131 ...
MAX1558/MAX1558H Dual, 3mm x 3mm, 1.2A/Programmable-Current USB Switches with Autoreset General Description
... latches the switch off if it is shorted for more than 20ms, saving system power. The shorted output is then tested to determine when the short is removed to automatically restart the channel. Each channel delivers up to 1.2A and meets all IEC specifications for USB ports. Low quiescent supply curren ...
... latches the switch off if it is shorted for more than 20ms, saving system power. The shorted output is then tested to determine when the short is removed to automatically restart the channel. Each channel delivers up to 1.2A and meets all IEC specifications for USB ports. Low quiescent supply curren ...
AN98 - Signal Sources, Conditioners and Power Circuitry Circuits of the Fall, 2004
... encompassing a wide and useful body of proven capabilities. They also represent substantial effort. These considerations make publication an almost obligatory proposition and, as such, a group of circuits is presented here. This is not the first time we have displayed such wares and, given the encou ...
... encompassing a wide and useful body of proven capabilities. They also represent substantial effort. These considerations make publication an almost obligatory proposition and, as such, a group of circuits is presented here. This is not the first time we have displayed such wares and, given the encou ...
MAX17094 Internal-Switch Boost Regulator with Integrated General Description
... The step-up DC-DC converter is a current-mode regulator that provides the regulated supply voltage for panel source driver ICs. The current-mode architecture provides fast-transient responses to pulsed loads typical of source driver loads. The high switching frequency, which is programmable to any f ...
... The step-up DC-DC converter is a current-mode regulator that provides the regulated supply voltage for panel source driver ICs. The current-mode architecture provides fast-transient responses to pulsed loads typical of source driver loads. The high switching frequency, which is programmable to any f ...
NCV7680EVB/D NCV7680 Evaluation Board Manual •
... are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor doe ...
... are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor doe ...
Slide 1 - Network and Systems Lab
... junction is 0.7V or more Ic = hFE × IB (hFE is current gain) The collector-emitter resistance RCE is controlled by the base current IB: IB = 0 RCE = infinity transistor off IB small RCE reduced transistor partly on ...
... junction is 0.7V or more Ic = hFE × IB (hFE is current gain) The collector-emitter resistance RCE is controlled by the base current IB: IB = 0 RCE = infinity transistor off IB small RCE reduced transistor partly on ...