MAX6948B High-Efficiency PWM LED Driver with Boost EVALUATION KIT AVAILABLE
... load current at up to 28V. The converter is stable under all load conditions from 5V up to 28V and includes open-circuit detection to prevent damage to the IC. An I2C-programmable 10-bit pulse-width modulation (PWM) signal enables 1024 levels of WLED intensity. The five GPIO ports function as logic ...
... load current at up to 28V. The converter is stable under all load conditions from 5V up to 28V and includes open-circuit detection to prevent damage to the IC. An I2C-programmable 10-bit pulse-width modulation (PWM) signal enables 1024 levels of WLED intensity. The five GPIO ports function as logic ...
Stability Analysis of a Microgrid System with a Constant Power Load
... present paper studies stability properties in case such a microgrid operates in island mode. First, a simple model describing the behavior of the microgrid is studied. When considering a linear load or a Constant Power Load CPL, the static and the dynamic resistances are determined. Such a CPL consu ...
... present paper studies stability properties in case such a microgrid operates in island mode. First, a simple model describing the behavior of the microgrid is studied. When considering a linear load or a Constant Power Load CPL, the static and the dynamic resistances are determined. Such a CPL consu ...
Lecture 26 slides - Digilent Learn site
... Phasor Diagrams – notes • Phasor lengths on diagram generally not to scale • They may not even share the same units • Phasor lengths are generally labeled on the diagram ...
... Phasor Diagrams – notes • Phasor lengths on diagram generally not to scale • They may not even share the same units • Phasor lengths are generally labeled on the diagram ...
FDDS10H04A_F085A Smart High Side Switch F DDS10H04A_F085A Sm
... The device can be operated in inverse load current mode (VOUT > Vbb > 0V). The current sense feature is not available during this kind of operation (IIS = 0). In case of inverse operation the intrinsic drain source diode is eventually conducting resulting in considerably increased power dissipation. ...
... The device can be operated in inverse load current mode (VOUT > Vbb > 0V). The current sense feature is not available during this kind of operation (IIS = 0). In case of inverse operation the intrinsic drain source diode is eventually conducting resulting in considerably increased power dissipation. ...
Design of a Noninvasive Bladder Urinary Volume Monitoring System
... 0.05% is used to calibrate the variable resistance and confirm that each time our adjustment is accurate. Then, ...
... 0.05% is used to calibrate the variable resistance and confirm that each time our adjustment is accurate. Then, ...
BD8962MUV
... The BD8962MUV is ROHM's high efficiency step-down switching regulator designed to produce a voltage as low as 0.8V from a supply voltage of 5.5V/3.3V. It offers high efficiency by using synchronous switches and provides fast transient response to sudden load changes by implementing current mode cont ...
... The BD8962MUV is ROHM's high efficiency step-down switching regulator designed to produce a voltage as low as 0.8V from a supply voltage of 5.5V/3.3V. It offers high efficiency by using synchronous switches and provides fast transient response to sudden load changes by implementing current mode cont ...
AI LOOK OVER HARDWARE DESIGN – AGENT WITH STATE
... (voltage) are used to select for transmission a part of a waveform which lies above or below some reference voltage level. In some applications diodes are combined with operational amplifier(s) to obtain precision limiting circuits [1]. In this paper a somewhat different approach (a functional appro ...
... (voltage) are used to select for transmission a part of a waveform which lies above or below some reference voltage level. In some applications diodes are combined with operational amplifier(s) to obtain precision limiting circuits [1]. In this paper a somewhat different approach (a functional appro ...
MAX1677 Compact, High-Efficiency, Dual-Output Step-Up and LCD Bias DC-DC Converter General Description
... set by LCDPOL input (Table 3). Figure 2 shows the MAX1677 configured for a positive LCD output voltage with a 3.3V main output. Figure 3 shows the MAX1677 configured for a negative LCD output. LCDPOL also allows the current limit of LCDLX to be reduced from 350mA to 225mA to allow minimum-size induc ...
... set by LCDPOL input (Table 3). Figure 2 shows the MAX1677 configured for a positive LCD output voltage with a 3.3V main output. Figure 3 shows the MAX1677 configured for a negative LCD output. LCDPOL also allows the current limit of LCDLX to be reduced from 350mA to 225mA to allow minimum-size induc ...
Single Pole IR
... applying molded case circuit breakers, the manufacturer must be consulted to verify single-pole interrupting ratings are in compliance with NEC Section 110-9. A simple solution exists to insure adequate interrupting ratings both in present installations and in future upgrades. Modern current-limitin ...
... applying molded case circuit breakers, the manufacturer must be consulted to verify single-pole interrupting ratings are in compliance with NEC Section 110-9. A simple solution exists to insure adequate interrupting ratings both in present installations and in future upgrades. Modern current-limitin ...
DESCRIPTION
... STEP 4: AC POWER CONNECTIONS *For 230 VAC input power, remove cover and connect jumpers as shown on printed circuit board silkscreen. STYLE 2: Encoders with single phase zero speed outputs. Typical for Avtron Encoders. The above connections will result in positive output of the K661 for both clockw ...
... STEP 4: AC POWER CONNECTIONS *For 230 VAC input power, remove cover and connect jumpers as shown on printed circuit board silkscreen. STYLE 2: Encoders with single phase zero speed outputs. Typical for Avtron Encoders. The above connections will result in positive output of the K661 for both clockw ...
BD9137MUV
... Switching of SLLM Function to PWM Fixed Function This IC operates at SLLM control and this control can be cancelled by activating EN terminal. Impressing voltage more than 2.0V to PWM terminal can activate the EN terminal, at the same time making PWM control to operate during light load. Constantly ...
... Switching of SLLM Function to PWM Fixed Function This IC operates at SLLM control and this control can be cancelled by activating EN terminal. Impressing voltage more than 2.0V to PWM terminal can activate the EN terminal, at the same time making PWM control to operate during light load. Constantly ...
ISO5451-Q1 High-CMTI 2.5-A and 5-A Isolated
... the printed-circuit board do not reduce this distance. Creepage and clearance on a printed-circuit board become equal in certain cases. Techniques such as inserting grooves and/or ribs on a printed circuit board are used to help increase these specifications. This coupler is suitable for basic elect ...
... the printed-circuit board do not reduce this distance. Creepage and clearance on a printed-circuit board become equal in certain cases. Techniques such as inserting grooves and/or ribs on a printed circuit board are used to help increase these specifications. This coupler is suitable for basic elect ...