TAS5102 数据资料 dataSheet 下载
... PVDD_X = 18 V, SE mode, RL = 4 Ω, ROC = 22 kΩ, CBST = 33-nF, audio frequency = 1 kHz, AES17 filter, FPWM = 384 kHz, ambient temperature = 25°C (unless otherwise noted). Audio performance is recorded as a chipset, using TAS5086 PWM processor with an effective modulation index limit of 96.1%. All perf ...
... PVDD_X = 18 V, SE mode, RL = 4 Ω, ROC = 22 kΩ, CBST = 33-nF, audio frequency = 1 kHz, AES17 filter, FPWM = 384 kHz, ambient temperature = 25°C (unless otherwise noted). Audio performance is recorded as a chipset, using TAS5086 PWM processor with an effective modulation index limit of 96.1%. All perf ...
BDTIC www.BDTIC.com/infineon T D A 4 8 6 3 -
... The control amplifier compares the divided output voltage at its inverting input with a highly accurate reference voltage of 2.5 V at its non-inverting input. The reference has a maximum deviation of less than ±2% over the total temperature range (-40°C < TJ < 150°C). A feedback network is inserted ...
... The control amplifier compares the divided output voltage at its inverting input with a highly accurate reference voltage of 2.5 V at its non-inverting input. The reference has a maximum deviation of less than ±2% over the total temperature range (-40°C < TJ < 150°C). A feedback network is inserted ...
1 - Telecommunications Industry Association
... division. Each direction of transmission for each subscriber uses either 4 kHz (single sideband) or 8 kHz (double sideband) of frequency spectrum. Generally, the carrier systems most susceptible to crosstalk are those that use double sideband modulation methods, 8 kHz of spectrum for each direction ...
... division. Each direction of transmission for each subscriber uses either 4 kHz (single sideband) or 8 kHz (double sideband) of frequency spectrum. Generally, the carrier systems most susceptible to crosstalk are those that use double sideband modulation methods, 8 kHz of spectrum for each direction ...
phys1444-lec9
... • Circuits containing both resistors and capacitors – RC circuits are used commonly in everyday life • Control windshield wiper • Timing of traffic light from red to green • Camera flashes and heart pacemakers ...
... • Circuits containing both resistors and capacitors – RC circuits are used commonly in everyday life • Control windshield wiper • Timing of traffic light from red to green • Camera flashes and heart pacemakers ...
RAJALAKSHMI INSTITUTE OF THCHNOLOGY
... maximum power transfer to the load connected to secondary or for obtaining maximum possible value of secondary voltage. A single tuned circuit is used for coupling an amplifier and radio receiver circuits. Double tuned circuit In double tuned circuits, a variable capacitor is used at input as well ...
... maximum power transfer to the load connected to secondary or for obtaining maximum possible value of secondary voltage. A single tuned circuit is used for coupling an amplifier and radio receiver circuits. Double tuned circuit In double tuned circuits, a variable capacitor is used at input as well ...
74LCXP16245 Low Voltage 16-Bit Bidirectional Transceiver with
... oriented applications. The device is designed for low voltage (2.5V or 3.3V) VCC applications with capability of interfacing to a 5V signal environment. The device is byte controlled. Each byte has separate control inputs which could be shorted together for full 16-bit operation. The T/R inputs dete ...
... oriented applications. The device is designed for low voltage (2.5V or 3.3V) VCC applications with capability of interfacing to a 5V signal environment. The device is byte controlled. Each byte has separate control inputs which could be shorted together for full 16-bit operation. The T/R inputs dete ...
L6384E
... High impedance pin with two functionalities. When pulled lower than Vdt [Typ. 0.5V] the device is shut down. A voltage higher than Vdt sets the dead time between high side gate driver and low side gate driver. The dead time value can be set forcing a certain voltage level on the pin or connecting a ...
... High impedance pin with two functionalities. When pulled lower than Vdt [Typ. 0.5V] the device is shut down. A voltage higher than Vdt sets the dead time between high side gate driver and low side gate driver. The dead time value can be set forcing a certain voltage level on the pin or connecting a ...
TPS2458 ATCA? AdvancedMC? Controller With I2C Evaluation
... top portion contains the TPS2458 IC and typically required components. The bottom section contains more ancillary circuitry intended to facilitate exercising the device through various application scenarios. Power connectors are organized with inputs along the left edge of the board, outputs along t ...
... top portion contains the TPS2458 IC and typically required components. The bottom section contains more ancillary circuitry intended to facilitate exercising the device through various application scenarios. Power connectors are organized with inputs along the left edge of the board, outputs along t ...
MAX15034 Configurable, Single-/Dual-Output, Synchronous Buck Controller for High-Current Applications General Description
... MOSFETs and is capable of providing more than 25A of load current. The MAX15034 uses average currentmode control with a switching frequency up to 1MHz per phase where each phase is 180° out of phase with respect to the other. Out-of-phase operation results in significantly reduced input capacitor ri ...
... MOSFETs and is capable of providing more than 25A of load current. The MAX15034 uses average currentmode control with a switching frequency up to 1MHz per phase where each phase is 180° out of phase with respect to the other. Out-of-phase operation results in significantly reduced input capacitor ri ...
Valve RF amplifier
A valve RF amplifier (UK and Aus.) or tube amplifier (U.S.), is a device for electrically amplifying the power of an electrical radio frequency signal.Low to medium power valve amplifiers for frequencies below the microwaves were largely replaced by solid state amplifiers during the 1960s and 1970s, initially for receivers and low power stages of transmitters, transmitter output stages switching to transistors somewhat later. Specially constructed valves are still in use for very high power transmitters, although rarely in new designs.