Cool-Switch®
... The PI2161 integrated Cool-Switch product takes advantage of two different technologies combining low RDS(on) N-channel MOSFETs with high density control circuitry to provide a high side fast Circuit Breaker solution. The PI2161’s 8.5 mΩ on state resistance MOSFET minimizes the voltage drop, at the ...
... The PI2161 integrated Cool-Switch product takes advantage of two different technologies combining low RDS(on) N-channel MOSFETs with high density control circuitry to provide a high side fast Circuit Breaker solution. The PI2161’s 8.5 mΩ on state resistance MOSFET minimizes the voltage drop, at the ...
- Toner Cable
... (hybrid fiber/coax) or PON (passive optical network) broadband CATV environment. The Model OTPN-412C is ideal for direct fiber transmission of CATV RF signals in FTTH, FTTx, MDU, corporate, government, educational, and other applications where a high performance, compact indoor node is required. The ...
... (hybrid fiber/coax) or PON (passive optical network) broadband CATV environment. The Model OTPN-412C is ideal for direct fiber transmission of CATV RF signals in FTTH, FTTx, MDU, corporate, government, educational, and other applications where a high performance, compact indoor node is required. The ...
lab2_cs355
... Digital Terminology: To use the 555 timer correctly you have to be aware of the correct terminology: ...
... Digital Terminology: To use the 555 timer correctly you have to be aware of the correct terminology: ...
1 Bakiss Hiyana binti Abu Bakar JKE, POLISAS
... magnetic field and either the field or the conductor moves, an emf (voltage) is induced in the conductor. This effect is called electromagnetic induction. » A loop of wire rotating in a magnetic field produces a voltage which constantly changes in amplitude and direction. » The waveform produced is ...
... magnetic field and either the field or the conductor moves, an emf (voltage) is induced in the conductor. This effect is called electromagnetic induction. » A loop of wire rotating in a magnetic field produces a voltage which constantly changes in amplitude and direction. » The waveform produced is ...
LNBH24
... tone waveform characteristics will always be internally controlled by the LNBH24 tone generator and the EXTM signal will be used as a timing control for DiSEqC tone data encoding on the VoTX output. A TTL-compatible 22 kHz signal is required for the proper control of the EXTM pin function. Before se ...
... tone waveform characteristics will always be internally controlled by the LNBH24 tone generator and the EXTM signal will be used as a timing control for DiSEqC tone data encoding on the VoTX output. A TTL-compatible 22 kHz signal is required for the proper control of the EXTM pin function. Before se ...
![1/2" [12.7 mm] Size 5 Diameter Hall Effect Precision](http://s1.studyres.com/store/data/004042290_1-85837aa989ab668504945c657226c3e2-300x300.png)
TPS40200-HT 数据资料 dataSheet 下载
... The controller uses a low-value current-sensing resistor in series with the input voltage and the power FET source connection to detect switching current. When the voltage drop across this resistor exceeds 100 mV, the part enters a hiccup fault mode at approximately 2% of the operating frequency. Th ...
... The controller uses a low-value current-sensing resistor in series with the input voltage and the power FET source connection to detect switching current. When the voltage drop across this resistor exceeds 100 mV, the part enters a hiccup fault mode at approximately 2% of the operating frequency. Th ...
Series and Parallel
... Revitalizing Achievement by using Instrumentation in Science Education 2004-2007 ...
... Revitalizing Achievement by using Instrumentation in Science Education 2004-2007 ...
Electronics - National University of Singapore
... A 3 F capacitor is in series with a 4 H inductor. Which of the following is correct? A – The combined impedance is always positive. B – The combined impedance is always negative. C – The combined impedance may be 0. D – None of the above. ...
... A 3 F capacitor is in series with a 4 H inductor. Which of the following is correct? A – The combined impedance is always positive. B – The combined impedance is always negative. C – The combined impedance may be 0. D – None of the above. ...
Rev. 0
... It is also highly recommended to use the Boot-Snap circuit to improve the interaction of the driver with the characteristics of the MOSFETs. If a simple bootstrap arrangement is used, make sure to include a proper snubber network on the SW node. ...
... It is also highly recommended to use the Boot-Snap circuit to improve the interaction of the driver with the characteristics of the MOSFETs. If a simple bootstrap arrangement is used, make sure to include a proper snubber network on the SW node. ...
TDA8953 2 × 210 W class-D power amplifier
... • Operating mode: the amplifier is fully operational, de-muted and can deliver an output signal A slowly rising voltage should be applied (e.g. via an RC network) to pin MODE to ensure pop noise-free start-up. The bias-current setting of the (VI converter) input stages is related to the voltage on t ...
... • Operating mode: the amplifier is fully operational, de-muted and can deliver an output signal A slowly rising voltage should be applied (e.g. via an RC network) to pin MODE to ensure pop noise-free start-up. The bias-current setting of the (VI converter) input stages is related to the voltage on t ...
VIPer12ADIP VIPer12AS LOW POWER OFF LINE SMPS PRIMARY SWITCHER
... Figure 9 : Internal Current Control Structure DRAIN ...
... Figure 9 : Internal Current Control Structure DRAIN ...
DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM
... Figure 9 : Internal Current Control Structure DRAIN ...
... Figure 9 : Internal Current Control Structure DRAIN ...
Valve RF amplifier
A valve RF amplifier (UK and Aus.) or tube amplifier (U.S.), is a device for electrically amplifying the power of an electrical radio frequency signal.Low to medium power valve amplifiers for frequencies below the microwaves were largely replaced by solid state amplifiers during the 1960s and 1970s, initially for receivers and low power stages of transmitters, transmitter output stages switching to transistors somewhat later. Specially constructed valves are still in use for very high power transmitters, although rarely in new designs.