lec5
... Let us find the characteristic of the parallel connection of R1 and R2 . Thus, Kirchhhofç laws imply that R1 and R2 have the same branch voltage, and the current through the parallel connection is the sum of the currents through each resistor. The characteristic of the parallel connection is thus o ...
... Let us find the characteristic of the parallel connection of R1 and R2 . Thus, Kirchhhofç laws imply that R1 and R2 have the same branch voltage, and the current through the parallel connection is the sum of the currents through each resistor. The characteristic of the parallel connection is thus o ...
fvco VREF
... deactivation of the charge current pump occurs less fre quently and the time to achieve phase lock is greater. In some instances, the amount of time to achieve phase lock can be ...
... deactivation of the charge current pump occurs less fre quently and the time to achieve phase lock is greater. In some instances, the amount of time to achieve phase lock can be ...
phase detector
... source. • The output of the phase-locked loop thus has a phase noise characteristic similar to that of the reference source, but operates at a higher frequency. • If a programmable frequency divider is used, it is possible to synthesize a large number of closely spaced frequencies with a relatively ...
... source. • The output of the phase-locked loop thus has a phase noise characteristic similar to that of the reference source, but operates at a higher frequency. • If a programmable frequency divider is used, it is possible to synthesize a large number of closely spaced frequencies with a relatively ...
Manual - Linear Technology
... DEMO MANUAL DC1500A LTC2393-16/LTC2392-16/ LTC2391-16: 16-Bit,1Msps/ 0.5Msps/0.25Msps Low Noise ADCs ...
... DEMO MANUAL DC1500A LTC2393-16/LTC2392-16/ LTC2391-16: 16-Bit,1Msps/ 0.5Msps/0.25Msps Low Noise ADCs ...
Passive Components - Resistors, Types of Resistors, Ohm`s Law
... possible.Of course, there are no ideal voltage sources. But one can get sources which are very close to ideal behaviour. ...
... possible.Of course, there are no ideal voltage sources. But one can get sources which are very close to ideal behaviour. ...
lo o c ic
... Linearisation accuracy: < 0.1% of reading <50ppm (typical) <100ppm (worst case) Drift with temperature: 48-62Hz, >-120dB Common mode rejection: Series mode rejection: 48-62Hz, >-93dB Input impedance: 100MΩ Cold junction compensation: >30:1 rejection of ambient change <±1°C at 25°C ambient Cold junct ...
... Linearisation accuracy: < 0.1% of reading <50ppm (typical) <100ppm (worst case) Drift with temperature: 48-62Hz, >-120dB Common mode rejection: Series mode rejection: 48-62Hz, >-93dB Input impedance: 100MΩ Cold junction compensation: >30:1 rejection of ambient change <±1°C at 25°C ambient Cold junct ...
Worksheet 4
... whole strand of lights does NOT go out. This is a parallel circuit. Draw your circuit by using standard symbols. ...
... whole strand of lights does NOT go out. This is a parallel circuit. Draw your circuit by using standard symbols. ...
DESCRIPTION FEATURES
... or 5 V card voltage from the power supply applied on the V DD pin. The digital ISO-7816-3 sequencer controls the converter. Card voltage selection is carried out by the digital input 5V/#V. The circuit is an inductive step-up converter/regulator. The external components required are 2 filter capacit ...
... or 5 V card voltage from the power supply applied on the V DD pin. The digital ISO-7816-3 sequencer controls the converter. Card voltage selection is carried out by the digital input 5V/#V. The circuit is an inductive step-up converter/regulator. The external components required are 2 filter capacit ...
CH_3 SPECIAL PURPOSE DIODE
... When the output terminals of the zener regulator are open (RL = ∞) or a no-load condition, the load current (IL) = 0 and all of the current is through the zener. When a load resistor (RL) is connected, a part of the total current is through the zener and an other part through RL. As RL is decreased, ...
... When the output terminals of the zener regulator are open (RL = ∞) or a no-load condition, the load current (IL) = 0 and all of the current is through the zener. When a load resistor (RL) is connected, a part of the total current is through the zener and an other part through RL. As RL is decreased, ...
DRV5033 Digital-Omnipolar-Switch Hall Effect Sensor
... The field polarity is defined as follows: a south pole near the marked side of the package is a positive magnetic field. A north pole near the marked side of the package is a negative magnetic field. The omnipolar configuration allows the hall sensor to respond to either a south or north pole. A str ...
... The field polarity is defined as follows: a south pole near the marked side of the package is a positive magnetic field. A north pole near the marked side of the package is a negative magnetic field. The omnipolar configuration allows the hall sensor to respond to either a south or north pole. A str ...
Operational amplifier
An operational amplifier (""op-amp"") is a DC-coupled high-gain electronic voltage amplifier with a differential input and, usually, a single-ended output. In this configuration, an op-amp produces an output potential (relative to circuit ground) that is typically hundreds of thousands of times larger than the potential difference between its input terminals.Operational amplifiers had their origins in analog computers, where they were used to do mathematical operations in many linear, non-linear and frequency-dependent circuits. The popularity of the op-amp as a building block in analog circuits is due to its versatility. Due to negative feedback, the characteristics of an op-amp circuit, its gain, input and output impedance, bandwidth etc. are determined by external components and have little dependence on temperature coefficients or manufacturing variations in the op-amp itself.Op-amps are among the most widely used electronic devices today, being used in a vast array of consumer, industrial, and scientific devices. Many standard IC op-amps cost only a few cents in moderate production volume; however some integrated or hybrid operational amplifiers with special performance specifications may cost over $100 US in small quantities. Op-amps may be packaged as components, or used as elements of more complex integrated circuits.The op-amp is one type of differential amplifier. Other types of differential amplifier include the fully differential amplifier (similar to the op-amp, but with two outputs), the instrumentation amplifier (usually built from three op-amps), the isolation amplifier (similar to the instrumentation amplifier, but with tolerance to common-mode voltages that would destroy an ordinary op-amp), and negative feedback amplifier (usually built from one or more op-amps and a resistive feedback network).