VOLTAGE REGULATORS
... been affected or attempted by persons other than pursuant to written authorization by Manufacturer. THIS WARRANTY IS EXCLUSIVE. The sole and exclusive obligation of Manufacturer shall be to repair or replace the defective Product in the manner and for the period provided above. Manufacturer shall no ...
... been affected or attempted by persons other than pursuant to written authorization by Manufacturer. THIS WARRANTY IS EXCLUSIVE. The sole and exclusive obligation of Manufacturer shall be to repair or replace the defective Product in the manner and for the period provided above. Manufacturer shall no ...
Modelling LED Lamps with Thermal Phenomena Taken into Account
... experimentally for two types of lamps and the good agreement between the results of calculations and measurements was obtained. ...
... experimentally for two types of lamps and the good agreement between the results of calculations and measurements was obtained. ...
Lab 2 Ohms Law
... The relationship between the electrical quantities current, voltage, and resistance is known as Ohm’s law. Essentially, voltage is proportional to current. The ratio between the voltage and current is the resistance. In this experiment, we will verify this relationship. Note that for some components ...
... The relationship between the electrical quantities current, voltage, and resistance is known as Ohm’s law. Essentially, voltage is proportional to current. The ratio between the voltage and current is the resistance. In this experiment, we will verify this relationship. Note that for some components ...
Model 2600B-PM-2 Protection Module
... instrument. They must be protected from electric shock and contact with hazardous live circuits. Maintenance personnel perform routine procedures on the product to keep it operating properly, for example, setting the line voltage or replacing consumable materials. Maintenance procedures are describe ...
... instrument. They must be protected from electric shock and contact with hazardous live circuits. Maintenance personnel perform routine procedures on the product to keep it operating properly, for example, setting the line voltage or replacing consumable materials. Maintenance procedures are describe ...
Call for Papers
... Short Course: October 21, 2017; Conference: October 19-20, 2017 The IEEE Bipolar/BiCMOS Circuits and Technology Meeting (BCTM) is the premier forum for technical communication mainly focused on the needs and interests of bipolar and BiCMOS technology and circuit community. Papers covering the design ...
... Short Course: October 21, 2017; Conference: October 19-20, 2017 The IEEE Bipolar/BiCMOS Circuits and Technology Meeting (BCTM) is the premier forum for technical communication mainly focused on the needs and interests of bipolar and BiCMOS technology and circuit community. Papers covering the design ...
Who really invented the Transistor
... The transistor was invented at Bell Laboratories in December 1947 (not in 1948 as is often stated) by John Bardeen and Walter Brattain. 'Discovered' would be a better word, for although they were seeking a solid-state equivalent to the vacuum tube, it was found accidentally during the investigation ...
... The transistor was invented at Bell Laboratories in December 1947 (not in 1948 as is often stated) by John Bardeen and Walter Brattain. 'Discovered' would be a better word, for although they were seeking a solid-state equivalent to the vacuum tube, it was found accidentally during the investigation ...
How to handle non-linear loads on a digital power supply
... How to Handle Non-Linear Loads on a Power Supply Non-linear loads, in the context of a power supply, are those that do not behave like an ideal resistor such as Point Of Load (POL) DC-DC converters and discharged capacitors that are switched onto the output causing high currents to flow until the ca ...
... How to Handle Non-Linear Loads on a Power Supply Non-linear loads, in the context of a power supply, are those that do not behave like an ideal resistor such as Point Of Load (POL) DC-DC converters and discharged capacitors that are switched onto the output causing high currents to flow until the ca ...
The Self-Healing Affect of - Electronic Concepts, Inc.
... and polypropylene have high surface oxygen contents. This is an important factor since oxygen is necessary to vaporize or “burn-off” the electrode around the fault area. PPS is an example of a dielectric which does not have high surface oxygen content and therefore has a very low potential for self- ...
... and polypropylene have high surface oxygen contents. This is an important factor since oxygen is necessary to vaporize or “burn-off” the electrode around the fault area. PPS is an example of a dielectric which does not have high surface oxygen content and therefore has a very low potential for self- ...
#2093
... The only controlled copy of this Data Sheet is the electronic read-only version located on the Cooper Bussmann Network Drive. All other copies of this document are by definition uncontrolled. This bulletin is intended to clearly present comprehensive product data and provide technical information th ...
... The only controlled copy of this Data Sheet is the electronic read-only version located on the Cooper Bussmann Network Drive. All other copies of this document are by definition uncontrolled. This bulletin is intended to clearly present comprehensive product data and provide technical information th ...
AIEEE 2005 (Physics)
... Two thin wires rings each having a radius R are placed at a distance d apart with their axes coinciding. The charges on the two rings are +q and –q. The potential difference between the centres of the two rings is ...
... Two thin wires rings each having a radius R are placed at a distance d apart with their axes coinciding. The charges on the two rings are +q and –q. The potential difference between the centres of the two rings is ...
View/Open - University of Hertfordshire
... In recent years current-mode circuits have become increasingly important in high speed analogue applications. Fundamental to these circuits is the need for an accurate and tunable voltage to current converter, or transconductor. The transconductor is also a key element in high frequency continuous-t ...
... In recent years current-mode circuits have become increasingly important in high speed analogue applications. Fundamental to these circuits is the need for an accurate and tunable voltage to current converter, or transconductor. The transconductor is also a key element in high frequency continuous-t ...
Power MOSFET
A power MOSFET is a specific type of metal oxide semiconductor field-effect transistor (MOSFET) designed to handle significant power levels.Compared to the other power semiconductor devices, for example an insulated-gate bipolar transistor (IGBT) or a thyristor, its main advantages are high commutation speed and good efficiency at low voltages. It shares with the IGBT an isolated gate that makes it easy to drive. They can be subject to low gain, sometimes to degree that the gate voltage needs to be higher than the voltage under control.The design of power MOSFETs was made possible by the evolution of CMOS technology, developed for manufacturing integrated circuits in the late 1970s. The power MOSFET shares its operating principle with its low-power counterpart, the lateral MOSFET.The power MOSFET is the most widely used low-voltage (that is, less than 200 V) switch. It can be found in most power supplies, DC to DC converters, and low voltage motor controllers.