
ADXRS642 英文数据手册DataSheet 下载
... rate sensitivity and temperature outputs are proportional to VRATIO. Therefore, it is most easily used with a supply-ratiometric ADC, which results in self-cancellation of errors due to minor supply variations. There is some small, usually negligible, error due to nonratiometric behavior. Note that ...
... rate sensitivity and temperature outputs are proportional to VRATIO. Therefore, it is most easily used with a supply-ratiometric ADC, which results in self-cancellation of errors due to minor supply variations. There is some small, usually negligible, error due to nonratiometric behavior. Note that ...
LM4766 Overture Audio Pwr Amp Series Dual
... All voltages are measured with respect to the GND pins (5, 10), unless otherwise specified. Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not ensure specific performance limits. E ...
... All voltages are measured with respect to the GND pins (5, 10), unless otherwise specified. Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not ensure specific performance limits. E ...
MAX6662 12-Bit + Sign Temperature Sensor with SPI-Compatible Serial Interface General Description
... The MAX6662 is a 12-bit + sign temperature sensor combined with a programmable overtemperature alarm and a 3-wire (SPI™-compatible) serial interface in a single package. It converts its die temperature into digital values using an internal analog-to-digital converter (ADC). The temperature data is s ...
... The MAX6662 is a 12-bit + sign temperature sensor combined with a programmable overtemperature alarm and a 3-wire (SPI™-compatible) serial interface in a single package. It converts its die temperature into digital values using an internal analog-to-digital converter (ADC). The temperature data is s ...
Design of bulk thermoelectric modules for integrated
... the TEC’s performance because it changes the value of and . In our paper, the TEC geometry factor is defined by , where is the TE element’s crossthe equation sectional area and is its leg length. In order to further improve the performance of the TEC, and were optimized at the same time without chan ...
... the TEC’s performance because it changes the value of and . In our paper, the TEC geometry factor is defined by , where is the TE element’s crossthe equation sectional area and is its leg length. In order to further improve the performance of the TEC, and were optimized at the same time without chan ...
Assembly Procedure SMD Attenuators
... The PI and T attenuators use 0805 resistors and for most values of attenuation will be accurate to within 0.25dB from DC to 3GHz.Note that resistor values above about 100 ohms will adversely impact high frequency response. For more detail see the attenuation graphs in the performance section. The re ...
... The PI and T attenuators use 0805 resistors and for most values of attenuation will be accurate to within 0.25dB from DC to 3GHz.Note that resistor values above about 100 ohms will adversely impact high frequency response. For more detail see the attenuation graphs in the performance section. The re ...
ADIS16120 数据手册DataSheet 下载
... connectors offers multiple configurations for use in mating to the ADIS16120. Consult the manufacturer reference material if this connector does not match system level requirements. The recommended pad/hole layout for this socket is shown in Figure 16. Use the alignment pins identified in this figur ...
... connectors offers multiple configurations for use in mating to the ADIS16120. Consult the manufacturer reference material if this connector does not match system level requirements. The recommended pad/hole layout for this socket is shown in Figure 16. Use the alignment pins identified in this figur ...
Computational fluid dynamic modeling of tin oxide deposition in an
... in this area include simulation of SnO2 deposition from SnCl4 in a horizontal cold wall APCVD reactor [3], computational modeling of silicon deposition from SiH4 in a stagnation rotating disk APCVD reactor [4], and numerical analysis of TiO2 deposition from titanium tetra-iso-propoxide in a cold wal ...
... in this area include simulation of SnO2 deposition from SnCl4 in a horizontal cold wall APCVD reactor [3], computational modeling of silicon deposition from SiH4 in a stagnation rotating disk APCVD reactor [4], and numerical analysis of TiO2 deposition from titanium tetra-iso-propoxide in a cold wal ...
Chapter 25 Electric Current and Direct
... Picture the Problem We can find the power delivered by the battery from the product of its emf and the current it delivers. The power delivered to the starter can be found from the product of the potential difference across the terminals of the starter (or across the battery when current is being dr ...
... Picture the Problem We can find the power delivered by the battery from the product of its emf and the current it delivers. The power delivered to the starter can be found from the product of the potential difference across the terminals of the starter (or across the battery when current is being dr ...
Lumped element model
The lumped element model (also called lumped parameter model, or lumped component model) simplifies the description of the behaviour of spatially distributed physical systems into a topology consisting of discrete entities that approximate the behaviour of the distributed system under certain assumptions. It is useful in electrical systems (including electronics), mechanical multibody systems, heat transfer, acoustics, etc.Mathematically speaking, the simplification reduces the state space of the system to a finite dimension, and the partial differential equations (PDEs) of the continuous (infinite-dimensional) time and space model of the physical system into ordinary differential equations (ODEs) with a finite number of parameters.