Download 150112 Fire Alarm

8
THESE DRAWINGS DEPICT GENERAL LOCATIONS OF LIFE SAFETY EQUIPMENT & FIELD DEVICES. EXACT ROUTING OF CONDUITS TO BE
DETERMINED IN THE FIELD BY THE INSTALLING CONTRACTOR TO SUIT CONDITIONS. ALL CHANGES SHALL BE CLEARLY INDICATED ON
THE RECORD DRAWINGS.
2.
SHOULD ANY CONDITIONS EXIST THAT DIFFER FROM WHAT IS INDICATED ON THESE DRAWINGS WHICH CAUSE MAJOR DEVIATIONS IN
THE WORK SHOWN, THE CONTRACTOR SHALL CONTACT SIMPLEXGRINNELL IN A TIMELY MANNER SO AS NOT TO IMPAIR THE
CONSTRUCTION SCHEDULE.
A STAMPED SET OF APPROVED FIRE ALARM DRAWINGS SHALL BE AT THE JOB SITE AND SHALL BE USED FOR INSTALLATION.
5.
THE POWER CIRCUIT TO THE FACP AND TO THE FIRE ALARM POWER SUPPLIES SHALL BE ON A DEDICATED 120V, 20A BRANCH CIRCUIT
BREAKER, AND SHALL HAVE A RED MARKING, LOCK-ON PROVISION AND SHALL BE IDENTIFIED AS "FIRE ALARM CIRCUIT CONTROL." THE
LOCATION OF THE CIRCUIT DISCONNECT MEANS (CIRCUIT BREAKER) SHALL BE PERMANENTLY IDENTIFIED AT THE FIRE ALARM
CONTROL UNIT.
6.
UPDATE THE AS-BUILT DRAWING SET DAILY WITH JOB PROGRESS. RETURN THE AS-BUILT DRAWING SET TO SIMPLEXGRINNELL NO
LATER THAN 7 DAYS AFTER FINAL TEST.
7.
THE CONTRACTOR WILL MAINTAIN ALL AREAS OF THE BUILDING IN A NEAT AND WORKMAN LIKE MANNER.
8.
DO NOT APPLY POWER EXCEPT IN THE PRESENCE OF A FACTORY TRAINED SIMPLEXGRINNELL TECHNICAL REPRESENTATIVE.
9.
ANY SMOKE DETECTOR HEAD INSTALLED BEFORE THE BUILDING IS CLEANED AND ACCEPTED SHALL BE COVERED TO PROTECT FROM
DUST. ANY FALSE ALARMS DUE TO DIRT CONTAMINATED HEADS SHALL BE THE RESPONSIBILITY OF THE FIRE ALARM INSTALLER.
10.
THE FIRE ALARM INSTALLER WILL MAINTAIN THE FIRE RESISTANCE INTEGRITY OF ALL WALL, CEILING, AND ROOF ASSEMBLIES ANY TIME
THAT WORK IS NOT ACTIVELY BEING PERFORMED.
11.
INSTALLATION OF DEVICES SHALL BE IN ACCORDANCE WITH MANUFACTURER'S INSTRUCTIONS. POWER LIMITED AND NON-POWER
LIMITED FIELD WIRING MUST BE INSTALLED WITHIN THE FACP ENCLOSURE IN ACCORDANCE WITH MANUFACTURER'S INSTRUCTIONS
AND NEC.
12.
ALL WIRING SHALL BE INSTALLED ACCORDING TO NFPA 70 (NEC).
13.
FIRE ALARM CIRCUITS SHALL BE IDENTIFIED IN ACCORDANCE WITH APPROPRIATE SECTION OF NEC 760. MARK ALL FIRE ALARM WIRES
IN ACCORDANCE WITH NEC 760 SECTIONS FOR POWER LIMITED AND NON-POWER LIMITED WIRE.
15.
C
OCCUPANCY TYPE:
CONTRACTOR IS RESPONSIBLE FOR MAKING AND OBTAINING APPROVAL FOR ALL NECESSARY ADJUSTMENTS IN CIRCUITING AS
REQUIRED TO ACCOMMODATE THE RELOCATION OF EQUIPMENT AND/OR DEVICES WHICH ARE AFFECTED BY ANY AUTHORIZED
CHANGE. ALL CHANGES SHALL BE CLEARLY INDICATED ON THE RECORD DRAWINGS.
4.
14
SYMBOL
BUILDING IS FULLY SPRINKLED
FAA
ALL WIRING TO BE CLASS B. WIRING IS STYLE Y FOR NOTIFICATION APPLIANCE CIRCUITS, STYLE B FOR INITIATING DEVICE CIRCUITS, AND STYLE 4
FOR SIGNALING LINE CIRCUITS.
AUTOMATIC FIRE ALARM SYSTEM SHALL TRANSMIT THE ALARM, SUPERVISORY AND TROUBLE SIGNALS TO AN APPROVED SUPERVISING STATION. THE
SUPERVISING STATION SHALL BE LISTED AS EITHER UUFX OR UUJS UNDERWRITERS LABORATORY OR SHALL MEET THE REQUIREMENTS OF FACTORY
MUTUAL RESEARCH APPROVAL STANDARD 3011. SUPERVISION OF SYSTEM AND LEASED TELEPHONE LINES SHALL BE ARRANGED BY THE OWNER.
P
FIRE ALARM CABLE INSTALLED IN UNDERGROUND CONDUIT OR OTHER WET LOCATIONS SHALL BE UL LISTED FOR WET LOCATIONS.
CALIFORNIA ELECTRIC CODE, 2013 EDITION, TITLE 24, PART 3
17.
FIRE ALARM CIRCUITS EXTENDING BEYOND ONE BUILDING AND RUN OUTDOOR SHALL BE INSTALLED IN ACCORDANCE WITH NFPA 70
ARTICLES 760, 770, 725 AND 800 WHERE APPLICABLE.
CALIFORNIA ELEVATOR SAFETY CONSTRUCTION CODE, 2013 EDITION
18.
ALL WIRING, INCLUDING SHIELDS MUST BE DRY AND FREE OF SHORTS AND GROUNDS.
3.
19.
ALL SHIELDED WIRE MUST HAVE SHIELD CONTINUITY AT FULL LENGTH OF THE WIRE.
20.
ONLY SYSTEM WIRING CAN BE RUN IN THE SAME CONDUIT.
21.
120VAC IS NOT PERMITTED IN THE SAME CONDUIT WITH LOW VOLTAGE WIRING.
22.
MAINTAIN 40 PERCENT CONDUIT FILL RATIO AS PER NEC REQUIREMENTS.
23.
EXISTING CONDUITS MAY BE USED BY THE INSTALLATION CONTRACTOR AS DEEMED NECESSARY, HOWEVER, ANY EXISTING CONDUIT
WILL BE USED ONLY IF CONDUITS MEET CURRENT STANDARDS AND CODES. SIMPLEXGRINNELL MAKES NO STATEMENTS WRITTEN OR
VERBAL AS TO THE CONDITION OF EXISTING CONDUITS.
4.
5.
6.
E
7.
UPON COMPLETION OF THE INSTALLATION OF THE
SYSTEM, A SATISFACTORY TEST OF THE ENTIRE SYSTEM
SHALL BE MADE IN THE PRESENCE OF A DSA PROJECT
INSPECTOR.
A STAMPED SET OF APPROVED FIRE ALARM DESIGN
DOCUMENTS SHALL BE MAINTAINED ON THE JOB SITE
AND USED FOR INSTALLATION.
22.
CONTROL PANELS AND REMOTE ANNUNCIATORS SHALL
BE INSTALLED WITH THEIR BOTTOMS MOUNTED AT 48”
ABOVE FINISHED FLOOR.
13.
VISUAL APPLIANCES SHOULD NOT EXCEED 2 FLASHES
PER SECOND AND SHOULD NOT BE SLOWER THAN 1
FLASH EVERY SECOND. THE DEVICE SHALL HAVE A
PULSING LIGHT SOURCE NOT LESS THAN 15 CANDELA.
VISUAL APPLIANCES WITHIN 55' FROM EACH OTHER
SHALL BE SYNCHRONIZED.
23.
THE INSTALLING CONTRACTOR SHALL PROVIDE SYSTEM
PROGRAMMING FOR SUPERVISORY MONITORING PER
CBC SECTION 901.6.2.
ANY DISCREPANCIES BETWEEN THE DRAWINGS AND
THE CODE OR RECOGNIZED STANDARDS SHALL BE
BROUGHT TO THE ATTENTION OF DSA AND THE
ARCHITECT/ENGINEER OF THE PROJECT.
17.
DSA, ARCHITECT/ENGINEER AND OWNER SHALL BE
NOTIFIED A MINIMUM OF 48 HOURS PRIOR TO THE FINAL
INSPECTION AND /OR TESTING.
ALL PENETRATIONS THROUGH RATED ASSEMBLIES
REQUIRING OPENING PROTECTION SHALL BE PROVIDED
WITH A PENETRATION FIRE STOP SYSTEM AS IDENTIFIED
IN CBC CHAPTER 7, UL OR OTHER LAB TESTING
CRITERIA.
8.
WALL MOUNTED VISUAL NOTIFICATION APPLIANCES
SHALL HAVE THEIR BOTTOMS MOUNTED AT 80” MINIMUM
AND 96” MAXIMUM ABOVE FINISHED FLOOR.
9.
WALL MOUNTED AUDIBLE NOTIFICATION APPLIANCES
SHALL HAVE THEIR TOPS MOUNTED AT 90” MINIMUM AND
96” MAXIMUM ABOVE FINISHED FLOOR AND NO CLOSER
THEN 6” TO A HORIZONTAL STRUCTURE.
10.
AUDIBLE APPLIANCES TO PROVIDE SOUND LEVEL AT
LEAST 15 dB ABOVE THE AVERAGE AMBIENT SOUND
LEVEL BUT NOT LESS THAN 75 dB AT 10 FEET OR MORE
THAN 110 dB AT THE MINIMUM HEARING DISTANCE .
SOUND LEVEL SHALL ACHIEVE 5 dB ABOVE MAXIMUM
SOUND LEVEL HAVING DURATION OF AT LEAST 60
SECONDS. MEASURE SOUND LEVEL AT FIVE FEET
ABOVE FINISHED FLOOR.
F
11.
ALL FIRE ALARM CIRCUITS SHALL BE IN CONDUIT,
SURFACE RACEWAY OR OPEN RUN ABOVE CEILINGS,
UNDER FLOORS AND IN WALLS IN A NEAT AND
PROTECTED MANNER AS INDICATED ON DESIGN
DOCUMENTS. EXPOSED CIRCUITS ARE ONLY PERMITTED
WHEN NOTED AS EXPOSED ON DESIGN DOCUMENTS.
19.
FIRE ALARM PANEL, REMOTE PANELS, POWER SUPPLIES
AND COMPONENTS SHALL BE SECURED TO MOUNTING
SURFACES PER MANUFACTURERS SPECIFICATIONS. NO
SINGLE DEVICE SHALL EXCEED THE WEIGHT OF 20 LBS.
WITHOUT SPECIAL MOUNTING DETAILS.
20.
AUDIBLE APPLIANCES SHALL BE SYNCHRONIZED
TEMPORAL CODE 3 PATTERN.
21.
24.
SUPERVISORY MONITORING SHALL BE TESTED AND
VERIFIED AS SENDING CORRECT SIGNALS IN
CONJUNCTION WITH FINAL ACCEPTANCE TEST.
25.
OWNER SHALL BE RESPONSIBLE FOR ESTABLISHING A
FIRE SYSTEM MONITORING CONTRACT OR PROVISIONS.
SMOKE DETECTORS SHALL NOT BE INSTALLED CLOSER
THAN 1' FROM FIRE SPRINKLERS OR 3' FROM ANY
SUPPLY DIFFUSER. IN AREA OF CONSTRUCTION OR
POSSIBLE DAMAGE/CONTAMINATION, NEWLY INSTALLED
FIRE ALARM DEVICES SHALL BE COVERED UNTIL THAT
AREA IS READY TO BE TURNED OVER TO THE OWNER.
18.
NO GRIP MANUAL PULL STATION
SIMPLEX 4099-9020
4" SQUARE BOX 2 1/8" DEEP W/SINGLE GANG COVER
7150-0026:0224
SMOKE SENSOR / BASE
SIMPLEX 4098-9714
SIMPLEX 4098-9792 BASE
4" OCTAGONAL BOX 1 1/2" DEEP
7272-0026:0218
7300-0026:0217
SIMPLEX 4098-9733
SIMPLEX 4098-9792 BASE
4" OCTAGONAL BOX 1 1/2" DEEP
7270-0026:0216
7300-0026:0217
RELAY IAM
SIMPLEX 4090-9002
4" SQUARE BOX 2 1/8" DEEP W/TWO GANG COVER
7300-0026:0223
#
ADDRESSABLE MULTI-CANDELA SPEAKER/STROBE,
WALL MOUNT, WHITE
# =CANDELA RATING, #W = SPEAKER TAP
**USE 70 VOLT TAP**
SIMPLEX 4906-9253
4" SQUARE BOX 1 1/2" DEEP W/ 1 1/2" EXTENSION RING
W/4905-9946 ADAPTER SKIRT WHEN SURFACE MOUNTED
7320-0026:0322
#
ADDRESSABLE MULTI-CANDELA SPEAKER/STROBE,
CEILING MOUNT, WHITE
# =CANDELA RATING, #W = SPEAKER TAP
**USE 70 VOLT TAP**
SIMPLEX 4906-9254
4" SQUARE BOX 1 1/2" DEEP W/ 1 1/2" EXTENSION RING
7320-0026:0322
#W
C
#
C
THE CONTRACTOR SHALL ADJUST/INSTALL ALL DEVICES
TO MAXIMIZE PERFORMANCE AND TO MINIMIZE FALSE
ALARMS.
PER CEC STANDARDS, ALL WIRING IS TO BE PULLED
THROUGH EACH JUNCTION BOX AND CONNECTED
DIRECTLY TO EACH FIRE DEVICE. DO NOT SPLICE THE
WIRE. THERE MUST BE AT LEAST 6" OF LEAD WIRE FROM
THE BOX TO THE DEVICE. ALL BOXES TO BE SIZED PER
CEC.
7120-0026:0179
AOM
#W
12.
16.
6 GANG BOX 3 1/2" DEEP
7300-0026:0223
#
ALL FIRE ALARM WIRING SHALL BE FLP OR FPLP (FIRE
POWER LIMITED OR FIRE POWER LIMITED PLENUM) AS
REQUIRED FOR APPLICATION. WIRING IN CONDUIT
ABOVE GROUND MAY BE THHN OR THWN.
SIMPLEX 4603-9101
SERIAL LCD ANNUNCIATOR
SINGLE GANG BOX 2 1/2" DEEP WITH COVER
#
15.
7165-0026:0251
SIMPLEX 4100-9111
REFER TO BATTERY CHARTS
SIMPLEX 4090-9001
NFPA 72, 2013 EDITION WITH CALIFORNIA AMENDMENTS
UNDERGROUND AND EXTERIOR CONDUITS TO HAVE
WATERTIGHT FITTINGS AND WIRE TO BE APPROVED FOR
WET LOCATIONS.
SUPPLIED BY SIMPLEXGRINNELL
(REFER TO MOUNTING DETAIL FOR SPECIFIC DIMENSIONS)
FIRE ALARM CONTROL PANEL
W / VARIOUS BATTERY SETS
INDIVIDUAL ADDRESSABLE MODULE
CALIFORNIA BUILDING CODE, 2013 EDITION, TITLE 24, PART 2
16.
14.
#
AC
C
E
RC
RD
RL
RR
=
=
=
=
=
=
=
ABOVE CEILING
CEILING MOUNTED
EXISTING TO REMAIN
EXISTING TO REMOVE AND COVER
EXISTING DEVICE TO BE RELOCATED
RELOCATED DEVICE
REMOVE EXISTING AND REPLACE W/NEW
WP
XP
H
AFF
AHJ
ALM
ANN
BMS
CBC
CD
CSFM
DET
DGP
EOL
EPO
FACP
FATC
FBO
FCC
FAA
FTR
FSD
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
WEATHERPROOF
EXPLOSION PROOF
HIGH HUMIDITY
ABOVE FINISHED FLOOR
AUTHORITY HAVING JURISDICTION
ALARM
ANNUNCIATOR
BUILDING MANAGEMENT SYSTEM
CALIFORNIA BUILDING CODE
(eg. 15CD) CANDELA
CALIFORNIA STATE FIRE MARSHAL
DETECTOR
DATA GATHERING PANEL
END OF LINE
EMERGENCY POWER OFF
FIRE ALARM CONTROL PANEL
FIRE ALARM TERMINAL CABINET
FURNISHED BY OTHERS
FIRE COMMAND CENTER
FIRE ALARM ANNUNCIATOR
FIRE ALARM TRANSPONDER
FIRE SMOKE DAMPER
HT
HVAC
IMS
MAX
MIN
N/A
NAC
NDU
NEC
NFPA
NIC
NPU
NTS
PAP
SCC
SLC
SMK
SUPV
TAC
TRBL
TS
TYP
UON
VCC
VT
WF
W
W/
W/O
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
HEIGHT
HEATING, VENTILATION, & AIR CONDITIONING
INFORMATION MANAGEMENT SYSTEM
MAXIMUM
MINIMUM
NOT APPLICABLE
NOTIFICATION APPLIANCE CIRCUIT EXTENDER
NETWORK DISPLAY UNIT
NATIONAL ELECTRICAL CODE
NATIONAL FIRE PROTECTION ASSOCIATION
NOT IN CONTRACT
NETWORK PROCESSING UNIT
NOT TO SCALE
PRE-ACTION PANEL
STATUS COMMAND CENTER
SIGNALING LINE CIRCUIT
SMOKE
SUPERVISORY
TRUEALERT ADDRESSABLE CONTROLLER
TROUBLE
TAMPER SWITCH
TYPICAL
UNLESS OTHERWISE NOTED
VOICE COMMAND CENTER
VALVE TAMPER
WATER FLOW
(eg. 1/2W) WATT
WITH
WITH OUT
SIMPLEX 49VO-WWF
4" SQUARE BOX 1 1/2" DEEP
W/4905-9940 ADAPTER SKIRT WHEN SURFACE MOUNTED
7125-0026:0373
ADDRESSABLE CEILING MOUNT MULTI-CANDELA STROBE ONLY WHITE
# =CANDELA RATING
SIMPLEX 4906-9204
HANDY BOX 1 1/2" DEEP
7125-0026:0235
SPEAKER ONLY, WALL MOUNT
#W = SPEAKER TAP
SIMPLEX 4902-9717
7320-0026:0242
**USE 70 VOLT TAP**
4" SQUARE BOX 1 1/2" DEEP W/ 1 1/2" RING
W/4905-9942 ADAPTER SKIRT WHEN SURFACE MOUNTED
SPEAKER ONLY, CEILING MOUNT
#W = SPEAKER TAP
SIMPLEX 4902-9721
4" SQUARE BOX 1 1/2" DEEP W/ 1 1/2" RING
7320-0026:0242
**USE 70 VOLT TAP**
WALL MOUNT MULTI-CANDELA WEATHERPROOF STROBE ONLY, WHITE
# = CANDELA RATING
SIMPLEX 49VO-WWFO-BA
49WPBB-AVVOWW BACK BOX SUPPLIED BY SIMPLEXGRINNELL
7125-0026:0371
#W
WP
SPEAKER ONLY, WALL MOUNT, WEATHERPROOF
#W=SPEAKER TAP
WHEELOCK ET-1010W
WBB-W
7320-0785:0105
VS
TAMPER SWITCH
SUPPLIED BY OTHERS
INSTALLED BY MECHANICAL CONTRACTOR
WF
WATERFLOW SWITCH
SUPPLIED BY OTHERS
INSTALLED BY MECHANICAL CONTRACTOR
A DEDICATED BRANCH CIRCUIT SHALL BE PROVIDED
FOR FIRE ALARM EQUIPMENT. THIS CIRCUIT SHALL BE
ENERGIZED FROM THE COMMON USE AREA PANEL AND
SHALL HAVE NO OTHER OUTLETS. THE BREAKER SHALL
HAVE A RED LOCKING DEVICE TO BLOCK THE HANDLE IN
THE “ON” POSITION. THE CIRCUIT BREAKER SHALL BE
LABELED “FIRE ALARM CIRCUIT CONTROL”. CIRCUIT ID
TO BE LABELED AT FIRE PANEL/EXTENDERS.
DUCT SMOKE SENSOR
SIMPLEX 4098-9756
MOUNT TO DUCTWORK
3240-0026:0241
REMOTE TEST STATION W/ LED AND KEY SWITCH
SIMPLEX 2098-9806
SINGLE GANG BOX 2 1/2" DEEP
7300-0026:0150
ENCAPSULATED RELAY
SIMPLEX 4098-9843
SINGLE GANG BOX 2 1/8" DEEP W/COVER
END-OF-LINE RESISTOR 3.3K (EOL)
END-OF-LINE RESISTOR 4.7K (EOL)
END-OF-LINE RESISTOR 6.8K (EOL)
END-OF-LINE RESISTOR 10K (EOL)
SIMPLEX 4081-9002
SIMPLEX 4081-9003
SIMPLEX 4081-9004
SIMPLEX 4081-9008
LINE ISOLATOR MODULE
SIMPLEX 4090-9116
P
10K
LIM
ALARM
DEVICE ADDRESS
BRANCH/REPEATER DESIGNATOR (OPT.)
(#) BRANCH, (E#:#) REPEATER:BRANCH
A1:2-1(1)
SPEAKER CIRCUIT
A
G
B
K
L
M
RUI/N2 COMMUNICATION 1
PAIR 18 AWG TWISTED
OVERALL SHIELD
SG ANIX./PAIGE 740215
AREA=0.0196 SQ. INCH
SG ANIX./PAIGE 740214L
AREA=0.0196 SQ. INCH
ANIXTER PART NUMBER
T740215
ANIXTER PART NUMBER
FAMC-1802C-1-2S-03B5
REMOTE TEST SWITCH/
LED CIRCUIT - (2) 2
CONDUCTOR 18 AWG SOLID
SG ANIX./PAIGE 454703ARE
AREA=0.0204 SQ. INCH
ANIXTER PART NUMBER
FA-1802C-1-1N-03-BX
SG ANIX./PAIGE 740132R
AREA=0.0141 SQ. INCH
REMOTE LED CIRCUIT
2 CONDUCTOR 16 AWG
SOLID
SG ANIX./PAIGE 454731ARE
AREA=0.0272 SQ. INCH
ANIXTER PART NUMBER
FA-1602C-1-1N-03-BX
MAPNET/IDNET CIRCUIT
1 PAIR 18 AWG TWISTED
OVERALL SHIELD
H
P
R
POWER CIRCUIT
2 CONDUCTOR
16 AWG SOLID (SUBSCRIPT
"r" IF RESETTABLE)
SITE PLAN - FIRE ALARM
1ST FLOOR PLAN - PHYSICAL EDUCATION BUILDING - FIRE ALARM
2ND FLOOR PLAN - PHYSICAL EDUCATION BUILDING - FIRE ALARM
SG ANIX./PAIGE 454740ARE
AREA=0.0208 SQ. INCH
FA4.01
ONE-LINE DIAGRAM - FIRE ALARM
ANIXTER PART NUMBER
FA-1602C-1-2N-03
FA5.01
CONTROL PANEL DIAGRAM - FIRE ALARM
FA6.01
FA6.02
CALCULATIONS - FIRE ALARM
CALCULATIONS - FIRE ALARM
FA7.01
FA7.02
FA7.03
FA7.04
DETAILS - FIRE ALARM
DETAILS - FIRE ALARM
DETAILS - FIRE ALARM
DETAILS - FIRE ALARM
ANIXTER PART NUMBER
T740215
ANIXTER PART NUMBER
FAMC-1802C-1-2S-03B5
SG ANIX./PAIGE 454731ARE
AREA=0.0272 SQ. INCH
SG ANIX./PAIGE 454740ARE
AREA=0.0208 SQ. INCH
(2) #14 AWG
AREA=0.0097 SQ. INCH (EACH)
SG ANIX./PAIGE 454719ARE
AREA=0.0333 SQ. INCH
ANIXTER PART NUMBER
FA-1402C-1-2N-03
ANIXTER PART NUMBER
FA-1602C-1-1N-03-BX
ANIXTER PART NUMBER
FA-1602C-1-2N-03
F
REMARKS
G
ARCHITECT'S STAMP
FIRE ALARM WIRING:
SIGNALING LINE CIRCUIT (SLC) - CLASS B:
SINGLE OPEN
SINGLE GROUND
WIRE-TO-WIRE SHORT
THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO LPAS, INC. AND IS FURNISHED FOR THE
PURPOSES OF REVIEW, BIDDING OR CONSTRUCTION OF THE PROJECT LISTED IN THE JOB TITLE BOX ABOVE
AND SHALL NOT BE USED FOR ANY OTHER PURPOSE OR RELEASED TO ANY OTHER PARTY WITHOUT THE
WRITTEN CONSENT OF LPAS, INC. INFOMATION CONTAINED HEREIN IS AN INSTRUMENT OF PROFESSIONAL
SERVICES AND SHALL REMAIN THE PROPERTY OF LPAS, INC. ALL RIGHTS RESERVED COPYRIGHT © 2009.
THIS DRAWING IS NOT FINAL OR TO BE USED FOR CONSTRUCTION UNTIL IT IS SIGNED BY THE ARCHITECT
AND ENGINEER.
NOTIFICATION APPLIANCE CIRCUIT (NAC) - CLASS B:
SINGLE OPEN
SINGLE GROUND
WIRE-TO-WIRE SHORT
H
CONSULTANT
PROJECT
CONTACT
Vb
WELLNESS CENTER SHEET INDEX
E N G I N E E R I N G
717 Market Street
Suite 500
San Francisco, CA 94103
TEL
415.489.7240
FAX
415.489.7289
www.interfaceengineering.com
WFA2.03 FLOOR PLANS - WELLNESS CENTER - FIRE ALARM
J
VISUAL/SIGNAL CIRCUIT - 2 CONDUCTOR 12 AWG STRANDED, UNSHEILDED
DIRECT BURIAL/UNDERGROUND IN CONDUIT/AERIAL (REQUIRES MESSENGER) - CABLE
CONDUIT ONLY: THWN
(2) #12 AWG (RED/BLACK)
AREA=0.0133 SQ. INCH (EACH)
SPEAKER CIRCUIT - 1 PAIR 18 AWG TWISTED OVERALL SHIELD
DIRECT BURIAL/UNDERGROUND IN CONDUIT/AERIAL (REQUIRES MESSENGER) - CABLE
ANIXTER PART NUMBER 2AS-1801POS
AREA=0.0615 SQ. INCH
CONDUIT SIZE
1/2"
3/4"
1"
12
PRO
F E S S I ON
ON LA
AS
AL
No. E16806
AT
EL
E CT RICA N
E O
OR
F CAL I F
11
SYMBOLS LISTS, GENERAL
NOTES AND SHEET INDEX FIRE ALARM
PROJECT NO: 1089-0001
CONDUCTOR AREA
0.60 SQ INCH *
0.82 SQ INCH *
1.34 SQ INCH *
CONDUIT SIZE
CONDUCTOR AREA
1-1/4"
0.12 SQ INCH *
1-1/2"
0.21 SQ INCH *
2"
0.34 SQ INCH *
* 40% FILL PER N.E.C.
DATE: 1.12.2015
THE CABLES SPECIFIED HERE ARE FOR REFERENCE OF REQUIRED ELECTRICAL CHARACTERISTICS
AS WELL AS CODE REQUIREMENTS. ALTERNATE SUPPLIERS MAY BE SUBSTITUTED PROVIDING
EQUIVALENT CHARACTERISTICS ARE MAINTAINED. ITEMS SUCH AS CAPACITANCE BETWEEN
CONDUCTORS AND WIRE GAUGE CAN BE CRUCIAL TO THE CIRCUIT DESIGN OF THIS SYSTEM
INSTALLATION.
REFERENCE https://www.anixter.com/customer/tycofs FOR SG ANIXTER CABLE DATA
K
D
MAPNET/IDNET CIRCUIT - 1 PAIR 18 AWG TWISTED OVERALL SHIELD
DIRECT BURIAL/UNDERGROUND IN CONDUIT/AERIAL (REQUIRES MESSENGER) - CABLE
ANIXTER PART NUMBER 2A-1202
AREA=0.0820 SQ. INCH
Sb
2014-0174
Joe Ripp
INTERFACE
ANIXTER PART NUMBER 2AS-1801POS
AREA=0.0615 SQ. INCH
J
APPROVAL
ST
SG ANIX./PAIGE 454731ARE
AREA=0.0272 SQ. INCH
SG ANIX./PAIGE 454740ARE
AREA=0.0209 SQ. INCH
MISC.
I NE ER
ANIXTER PART NUMBER
FA-1602C-1-2N-03
SUPERVISORY
U
(4) #16 AWG
AREA=0.0072 SQ. INCH (EACH)
WIRING THAT LEAVES THE BUILDING
Mb
FA1.01
FA2.01
FA2.02
SG ANIX./PAIGE 740214L
AREA=0.0196 SQ. INCH
SG ANIX./PAIGE 454718ARE
AREA=0.0380 SQ. INCH
ANIXTER PART NUMBER
FA-1402C-1-1N-03-BX
AUDIO CIRCUIT
1 PAIR 16 AWG TWISTED
UNSHIELDED
(2) #16 AWG
AREA=0.0072 SQ. INCH (EACH)
SYMBOLS LISTS, GENERAL NOTES AND SHEET INDEX - FIRE ALARM
ANIXTER PART NUMBER
FA-1802C-1-2N-03
SG ANIX./PAIGE 740215
AREA=0.0196 SQ. INCH
ANIXTER PART NUMBER
FA-1602C-1-1N-03-BX
RELAY CIRCUIT
2 CONDUCTOR
14 AWG SOLID
(4) #18 AWG
AREA=0.0055 SQ. INCH (EACH)
SHEET INDEX
FA0.01
TROUBLE
ENG
S
SINGLE CONDUCTOR(THHN,TFFN)
E
7300-0026:0252
MANUAL PULL STATION
AREA SMOKE DETECTOR
SMOKE DETECTOR ELEV. LOBBY
SMOKE DETECTOR ELEV. MACH. ROOM
HEAT DETECTOR
HEAT DETECTOR ELEV. MACH. ROOM
DUCT MOUNTED SMOKE DETECTOR
WATERFLOW SWITCH
TAMPER SWITCH
POST INDICATOR VALVE SWITCH
SYSTEM RESET
SIGNAL SILENCE
AC POWER FAILURE
FIRE ALARM SYSTEM LOW BATTERY
SPEAKER DEVICE
PLENUM RATED: FPLP
SG ANIX./PAIGE 454725ARE
AREA=0.0468 SQ. INCH
ANIXTER PART NUMBER
FA-1202C-1-2N-03
RISER RATED: FPLR
CAUSE
DEVICE DESIGNATOR
S2-1
FIRE ALARM WIRE LIST
DATE
SEQUENCE OF OPERATION
ADDRESSABLE DEVICES NUMBERING
WIRE SCHEDULE
ISSUE
DEVICE ADDRESS
CHANNEL DESIGNATOR
ADDRESSABLE POWER SUPPLY
(EPS, TPS)
SG ANIX./PAIGE 454720ARE
AREA=0.0491 SQ. INCH
ANIXTER PART NUMBER
FA-1202C-1-1N-03
4" SQUARE BOX 2 1/8" DEEP W/TWO GANG COVER
M2-1
THE INSTALLING CONTRACTOR SHALL PROVIDE A
RECORD OF COMPLETION PER NFPA 72, FIGURE
10.18.2.1.1.
C
D
DEVICE ADDRESSING LEGEND
ADDRESSABLE CARD (IDNET OR MAPNET)
PHYSICAL EDUCATION BUILDING AND
RENOVATED LAB BUILDING
NO.
WP
ABBREVIATIONS LEGEND
SAN JOSE CITY
COLLEGE
SAN JOSE, CALIFORNIA
WALL MOUNT MULTI-CANDELA STROBE ONLY, WHITE
# = CANDELA RATING
ADDRESSABLE NOTIFICATION DEVICE
CIRCUIT DESCRIPTION
ADDRESSABLE
NOTIFICATION CIRCUIT
12 AWG SOLID
UNSHIELDED TWISTED PAIR
CSFM #
BACKBOX
AIM
FIRE ALARM APPLICABLE CODES & STANDARDS
CALIFORNIA FIRE CODE, 2013 EDITION, TITLE 24, PART 9
INSTALLATION OF THE SYSTEM SHALL NOT BE STARTED
UNTIL DETAILED DESIGN DOCUMENTS AND
SPECIFICATIONS, INCLUDING STATE FIRE MARSHAL
LISTING NUMBERS FOR EACH COMPONENT OF THE
SYSTEM, HAVE BEEN APPROVED BY DSA.
MODEL#
B
DSA NOTES
2.
DESCRIPTION
HEAT SENSOR / BASE
FIRE ALARM CABLE INSTALLED IN THE VERTICAL RUNS AND PENETRATE MORE THAN ONE FLOOR OR CABLES INSTALLED IN VERTICAL
RUNS IN SHAFTS SHALL BE TYPE FPLR.
D
1
A
PROVIDE AND INSTALL A NEW AUTOMATIC AND MANUAL FIRE ALARM SYSTEM AS SHOWN ON DRAWINGS.
FIRE ALARM CABLE INSTALLED IN DUCTS, PLENUM, AND OTHER SPACES USED FOR ENVIRONMENTAL AIR SHALL BE TYPE FPLP.
APPLICABLE STANDARD AND CODES:
2013 NFPA 72
2013 CALIFORNIA FIRE CODE
2013 CALIFORNIA BUILDING CODE
2013 CALIFORNIA MECHANICAL CODE
2013 CALIFORNIA ELECTRICAL CODE
2
FIRE ALARM SYMBOLS LEGEND
A-3 ASSEMBLY GROUP
A-4 ASSEMBLY GROUP
B BUSINESS GROUP
S-1 STORAGE GROUP
SPRINKLER PROTECTION:
3
SYMBOL KEY
JURISDICTIONS WITHIN THE STATE MAY HAVE AMENDMENTS TO THE STATE ADOPTED CODE. CHECK
WITH THE LOCAL JURISDICTION AUTHORITY FOR MORE DETAILS.
1.
4
L
B
5
IA
1.
3.
6
SYSTEM DESCRIPTION / SCOPE OF WORK
GENERAL NOTES
A
7
J
9
RE
10
R EG I S T E
11
AL
AR
EF
AL M A
AR T F FEC
A
A L M A CP T
AR T A
M N
AC SIG NU
TIV N NC
RE AT AL T IAT
CA E A O OR
CE
U
L
EL L EL DIB NT
EV EV LE RA
L
A
A
AC TO ATO ND MO
TIV R P R T VIS NI
AT OW O D IB TOR
L
E
FIR ER ESI E AL ING
G
S
TR
EM HU NA AR ST
OU
AN NT TE MS ATI
D
'S
T O
T
TR BLE
HA RIP FL HR N
OU AT
OO OU
T
IN
R
GO
TR BLE FAC
SI
UT
DE
O U AT P
BL A
EL
N
E
EV
SI NU
.C
GN NC
AB
SU
AL IAT
PE
O
T
O
R
SU RVI
CE
PE SO
NT
R
RA
SU RVI Y A
LM
PE SO T F
R
ON
RV Y AC
IT
A
P
IS
OR
OR T A
N
IN
Y
N
DI
G
SI UN
SP
ST
GN C
LA
AT
I
AL AT
DE Y
IO
O
T
C
AC H
N
O
R
CE
SH TIV ANG
N
A
UT T E
TR
E
O
AL
SY DOW AU F S
MO
ST N DIB TA
NI
EM H LE TU
TO
NO VAC AN S
RI
NG
RM UN D V
ST
AL IT ISI
BL
AT
E
IO
AL
N
AR
MS
12
10
K
SHEET NO:
FA0.01
9
8
7
6
5
4
3
2
1
DSA SUBMITTAL
12
11
10
9
8
7
6
5
4
3
2
1
A
#
A
B
D
H
B
Y
SAN JOSE CITY
COLLEGE
PHYSICAL EDUCATION BUILDING AND
RENOVATED LAB BUILDING
SAN JOSE, CALIFORNIA
C
C
WV
NO.
ISSUE
DATE
PIV
DCDA
FH
Mb
D
D
FAA
1" FA CONDUIT
2" FA CONDUIT
WELLNESS BUILDING
VT
T
D
Mb,Sb,Vb
D
D
D
2" FA CONDUIT
#
WV
Mb,Sb,Vb
FACP
#
PHYSICAL EDUCATION BUILDING
#
E
#
#
E
#
#
#
#
#
FH
UP
F
F
∀
RAMP
#
#
Α
#
LAMP
G
#
G
APPROVAL
#
ARCHITECT'S STAMP
#
THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO LPAS, INC. AND IS FURNISHED FOR THE
PURPOSES OF REVIEW, BIDDING OR CONSTRUCTION OF THE PROJECT LISTED IN THE JOB TITLE BOX ABOVE
AND SHALL NOT BE USED FOR ANY OTHER PURPOSE OR RELEASED TO ANY OTHER PARTY WITHOUT THE
WRITTEN CONSENT OF LPAS, INC. INFOMATION CONTAINED HEREIN IS AN INSTRUMENT OF PROFESSIONAL
SERVICES AND SHALL REMAIN THE PROPERTY OF LPAS, INC. ALL RIGHTS RESERVED COPYRIGHT © 2009.
#
THIS DRAWING IS NOT FINAL OR TO BE USED FOR CONSTRUCTION UNTIL IT IS SIGNED BY THE ARCHITECT
AND ENGINEER.
H
CONSULTANT
2014-0174
Joe Ripp
J
ON LA
AS
AL
No. E16806
ST
#
AT
EL
L
E CT RICA N
E O
OR
F CAL I F
IA
#
F E S S I ON
I NE ER
#
717 Market Street
Suite 500
San Francisco, CA 94103
TEL
415.489.7240
FAX
415.489.7289
www.interfaceengineering.com
PRO
U
E N G I N E E R I N G
D
ENG
INTERFACE
RE
CONTACT
#
#
PROJECT
R EG I S T E
#
#
H
#
#
J
J
#
SITE PLAN - FIRE ALARM
1 SITE PLAN - FIRE ALARM
0'
20'
40'
1" = 20'-0"
PROJECT NO: 1089-0001
DATE: 1.12.2015
K
K
SHEET NO:
FA1.01
12
11
10
9
8
7
6
5
4
3
2
1
DSA SUBMITTAL
12
11
10
9
8
7
6
5
4
3
2
1
SHEET KEYNOTES
A
B
A.5
C
D
E
F
F.2
G
H
J
A
VS AIM
1
WF AIM
1
PROVIDE (1) 2" CONDUIT TO WELLNESS CENTER. PROVIDE CONNECTION
FROM 2" CONDUIT TO RESTROOM BUILDING VIA HANDHOLE, 2" CONDUIT,
AND A WEATHERPROOF JUNCTION BOX. IF WELLNESS CENTER IS NOT
CONSTRUCTED, CONDUIT AND WIRING TO STOP AT RESTROOM BUILDING.
2
MULLION MOUNT PULL STATION. USE MANUFACTURER'S SURFACE MOUNT
BACK BOX AND CONCEAL WIRING WITHIN MULLION.
A
M1-17
M1-18
M1-32
AIM
TO PIV
Mb
2
P
M1-13
P
M1-4
STAFF LOCKER 30
105
1/2W
C
M
A,M,S
FAA
OPEN OFFICE
102
A1:1-17(1)
S1-18
MACH. ROOM
120
2A,B,M,P,2S
2A,B,M,P,2S
M1-6
A,M,S
MENS
106
OFFICE
103
DEAN'S OFFICE
104
1/2W
75
75
A,M,S
1/4W
A1:1-16(1)
S1-17
C
A,M,S
1/4W
HALL
167
WOMENS
107
C
S1-16
1/4W
A,M,S
A1:1-15(1)
S1-15
A1:1-14(1)
S1-14
30
LOBBY
101
A,M,S
C
STAFF LOCKER 30
108
C
OFFICE
110
OFFICE
109
1/2W
EOL
OFFICE
111
A1:1-13(1)
S1-13
30
B
A1:1-12(1)
S1-12
C
1/4W
M1-7
M1-8
M1-9
M1-10
M1-11
2A,M,2S
2A,B,M,P,2S
ELEV.
E1.1
PUBLIC MEN'S RESTROOM
126
A,M,S
OFFICE
112
C
1/2W
TICKETS/ CONCESSIONS
124
2A,B,M,P,2S
AOM AOM AOM
OPEN
TO
ABOVE
M1-12
A1:1-18(1)
S1-19
M1-5
AIM AOM
75
PUBLIC WOMEN'S
RESTROOM
122
M
B
M
RISER
123
A,M,S
75
OFFICE
113
PHYSICAL EDUCATION BUILDING AND
RENOVATED LAB BUILDING
M1-3
P
3A,B,M,P,3S
2A,M,2S
C
A1:1-11(1)
S1-11
1
1/2W
Mb,Sb,Vb
LIM
TELECOM
125
SAN JOSE CITY
COLLEGE
SAN JOSE, CALIFORNIA
M1-31
3A,B,M,P,3S
3
C
C
TO
FACP
30
A,M,S
S3-10
A,M,S
2W
WG
EOL
WG
2W
C
A1:1-9(1)
S1-9
15
A1:1-10(1)
S1-10
NO.
ISSUE
DATE
VEST.
128
A1:2-1(1)
S2-1
C
WP
WP
1/2W
WOMEN'S STUDENT
RESTROOM
130
WOMEN'S STUDENT
LOCKERS
3A,B,M,P,3S
129
S3-1
30
A,2S
1/2W
1/4W
A,M,S
MEN'S STUDENT LOCKERS
132
A,M,S
30
MEN'S STUDENT RESTROOM
131
A1:1-7(1)
S1-7
1/2W
WP
30
A,2S
A,M,S
C
D
A1:1-8(1)
S1-8
WP
1/2W
D
4
135
WG
WG
2W S3-2
135
WG
WG
M1-22
WG P
2W
S2-2
C
A,M,S
FACP
OFFICE
135
S3-9
3A,B,M,P,3S
3A,B,M,P,3S
P
1/4W
M1-1
110
A,M,S
A,M,S
ELEC.
136
M
M1-2
A1:1-1(1)
S1-1
1/2W
C
EQUIPMENT STORAGE
133
A,M,2S
2A,M,P,2S
E
2W
5
S3-8
2W
SPECTATOR GYMNASIUM
160
WG
E
UP TO
2ND
FLOOR
WG
S3-3
15
GYM EQUIPMENT
134
A1:2-2(1)
S2-3
C
1/4W
A,M,S
A1:1-2(1)
S1-2
A,M,S
1/4W
15
C
TRAINING STAFF ROOM
139
S3-7
F
M1-21
6
A,M,S
30
S3-4
WG
2W
135
P
WG
WG
TRAINING ROOM
138
2W
WG
135
WG
A,M,2S
C
1/2W
A1:1-3(1)
S1-3
A,M,2S
30
1/2W
C
A1:1-4(1)
S1-4
F
M
P
A,M,2S
M1-19
2
S2-4
A,M,S
C
A,M,S
1/4W
A,M,S
2W
G
2W
WG
WG
EAST CORRIDOR
137
S3-5
S3-6
30
1/2W
MULTIPURPOSE CLASSROOM
141
A1:1-6(1)
S1-6
A,2S
C
A,M,S
G
30
C
1/2W
A1:1-5(1)
S1-5
7
ARCHITECT'S STAMP
15
M
1/4W
1/4W
A1:2-17(1)
S2-18
C
SOUTH CORRIDOR
150
A,M,S
C
M1-16
A,M,S
S2-13
A1:2-9(1)
S2-11
C
A,M,S
C
A,M,2S
S2-6
M
1/4W
M
THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO LPAS, INC. AND IS FURNISHED FOR THE
PURPOSES OF REVIEW, BIDDING OR CONSTRUCTION OF THE PROJECT LISTED IN THE JOB TITLE BOX ABOVE
AND SHALL NOT BE USED FOR ANY OTHER PURPOSE OR RELEASED TO ANY OTHER PARTY WITHOUT THE
WRITTEN CONSENT OF LPAS, INC. INFOMATION CONTAINED HEREIN IS AN INSTRUMENT OF PROFESSIONAL
SERVICES AND SHALL REMAIN THE PROPERTY OF LPAS, INC. ALL RIGHTS RESERVED COPYRIGHT © 2009.
A1:2-3(1)
S2-5
C
A,M,S
1/4W
A,2S
P
8
15
15 1/4W
JAN.
140
M1-14
APPROVAL
M1-20
P
P
THIS DRAWING IS NOT FINAL OR TO BE USED FOR CONSTRUCTION UNTIL IT IS SIGNED BY THE ARCHITECT
AND ENGINEER.
A,2S
LAUNDRY
159
A,2S
WP
C
A1:2-15(1)
S2-16
15
1/2W
VEST.
149
A1:2-4(1)
A,2S
15
A1:2-13(1)
S2-14
C
VEST.
144
H
FOOTBALL LOCKER ROOM
146
1/2W
A1:2-5(1)
S2-7
A,M,2S
PROJECT
30
A,2S
A,2S
WP
30
A1:2-16(1)
S2-17
WP
1/2W
1/2W
C
EOL
J
A1:2-19(1)
S2-20
C
1/2W
C
A1:2-8(1)
S2-10
INTERFACE
E N G I N E E R I N G
P
1/2W
A1:2-11(1)
S2-12
MEN'S TEAM SHOWER
147
30
WP
M
M1-15
717 Market Street
Suite 500
San Francisco, CA 94103
TEL
415.489.7240
FAX
415.489.7289
www.interfaceengineering.com
A1:2-6(1)
S2-8
A1:2-14(1)
S2-15
TEAM DRESSING ROOM
155
C
TEAM DRESSING ROOM
148
WP
1/2W
A,M,2S
J
9
D
PRO
F E S S I ON
ON LA
AS
AL
No. E16806
ST
HYDRONICS
157
15
A,M,2S
1/2W
2014-0174
Joe Ripp
I NE ER
A,S
30
A1:2-7(1)
S2-9
CONTACT
U
A,2S
30
1/2W
ENG
C
15
CONSULTANT
AT
EL
E CT RICA N
E O
OR
F CAL I F
L
C
A,2S
15
IA
A1:2-18(1)
S2-19
A1:2-10(1)
MEN'S TEAM TOILETS
145
J
1/2W
15
15
RE
C
15
15
R EG I S T E
1/2W
H
ELEC.
151
A1:2-12(1)
WOMEN'S TEAM TOILETS
153
A,M,S
1ST FLOOR PLAN PHYSICAL EDUCATION
BUILDING - FIRE ALARM
PROJECT NO: 1089-0001
DATE: 1.12.2015
1 1ST FLOOR PLAN - PHYSICAL EDUCATION BUILDING - FIRE ALARM
0'
4'
8'
16'
1/8" = 1'-0"
K
K
SHEET NO:
FA2.01
12
11
10
9
8
7
6
5
4
3
2
1
DSA SUBMITTAL
12
11
10
A
9
B
A.5
8
C
7
6
D
5
E
F
F.2
4
G
3
2
H
1
J
A
A
1
2
B
B
JANITOR
203
75
C
1/2W
EOL
75
A2:1-8(1)
S4-1
A,S
C
1/2W
A2:1-7(1)
S4-2
SAN JOSE CITY
COLLEGE
P
OPEN
TO
BELOW
M1-28
M
PHYSICAL EDUCATION BUILDING AND
RENOVATED LAB BUILDING
ELEV.
E1.1
M1-27
15
C
SAN JOSE, CALIFORNIA
A,S
M
1/4W
A2:2-1(1)
S5-1
C
C
3
NO.
FITNESS CENTER
202
A,M,2S
75
1/2W
1/4W
C
75
A2:1-5(1)
S4-4
1/2W
A,S
ISSUE
DATE
A2:1-6(1)
S4-3
A,S
S5-2
M1-26
D
D
1
AHU-2
FA7.01
4
ON ROOF
A,M,2S
A,M,P,S
15
110
1/2W
110
C
SPECTATOR GYMNASIUM
160
1/4W
A2:1-4(1)
S4-5
C
A2:2-2(1)
S5-3
C
A,2S
1/2W
A2:1-1(1)
S4-6
DOWN TO
1ST FLOOR
A,M,2S
E
E
A,M,P,S
A,M,P,S
OPEN
TO
BELOW
5
CORRIDOR
201
A,M,P,S
A,M,P,S
1
FA7.01
M1-25
AHU-3
A,2S
ON ROOF
S5-4
C
1/4W
F
F
A,M,P,S
6
15
C
1/4W
A2:2-3(1)
S5-5
A,2S
75
C
C
1/2W
A2:1-2(1)
S4-7
A2:1-3(1)
S4-8
A,M,P,S
G
75
M1-29
1/2W
G
EXERCISE LAB
205
P
ARCHITECT'S STAMP
APPROVAL
7
M,P
1
FA7.01
8
75
AHU-1
A2:2-4(1)
S5-6
THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO LPAS, INC. AND IS FURNISHED FOR THE
PURPOSES OF REVIEW, BIDDING OR CONSTRUCTION OF THE PROJECT LISTED IN THE JOB TITLE BOX ABOVE
AND SHALL NOT BE USED FOR ANY OTHER PURPOSE OR RELEASED TO ANY OTHER PARTY WITHOUT THE
WRITTEN CONSENT OF LPAS, INC. INFOMATION CONTAINED HEREIN IS AN INSTRUMENT OF PROFESSIONAL
SERVICES AND SHALL REMAIN THE PROPERTY OF LPAS, INC. ALL RIGHTS RESERVED COPYRIGHT © 2009.
A,M,P,S
2W
WP
EOL
THIS DRAWING IS NOT FINAL OR TO BE USED FOR CONSTRUCTION UNTIL IT IS SIGNED BY THE ARCHITECT
AND ENGINEER.
M1-30
H
H
CONSULTANT
2014-0174
Joe Ripp
J
J
9
4'
8'
J
AL
EL
L
E CT RICA N
E O
OR
F CAL I F
IA
AT
2ND FLOOR PLAN PHYSICAL EDUCATION
BUILDING - FIRE ALARM
PROJECT NO: 1089-0001
1 2ND FLOOR PLAN - PHYSICAL EDUCATION BUILDING - FIRE ALARM
0'
ON LA
AS
No. E16806
ST
717 Market Street
Suite 500
San Francisco, CA 94103
TEL
415.489.7240
FAX
415.489.7289
www.interfaceengineering.com
F E S S I ON
I NE ER
E N G I N E E R I N G
PRO
U
INTERFACE
D
ENG
TERRACE
T1
RE
CONTACT
R EG I S T E
PROJECT
DATE: 1.12.2015
16'
1/8" = 1'-0"
K
K
SHEET NO:
FA2.02
12
11
10
9
8
7
6
5
4
3
2
1
DSA SUBMITTAL
12
11
10
9
8
7
6
5
4
3
2
1
GENERAL SHEET NOTES
A
A.
A
ONE-LINE DIAGRAM IS DIAGRAMMATIC. REFER TO FLOOR PLANS FOR
EXACT NUMBER AND LOCATION OF DEVICES AND APPLIANCES.
SHEET KEYNOTES
1
IF WELLNESS CENTER IS NOT CONSTRUCTED, WIRING AND CONDUIT IS TO
STOP AT THE RESTROOM BUILDING.
B
B
10K
10K
10K
P
P
P
R
K
R
K
R
K
M1-25
M1-26
PHYSICAL EDUCATION BUILDING AND
RENOVATED LAB BUILDING
M1-30
M
ROOF PE BUILDING
2W
1/4W
1/4W
1/4W
1/4W
SAN JOSE CITY
COLLEGE
ROOF PE BUILDING
SAN JOSE, CALIFORNIA
1/4W
SPEAKER CIRCUIT(S5)
C
C
WP
S5-6
1/2W
1/2W
S5-5
1/2W
S5-4
1/2W
S5-3
1/2W
S5-2
1/2W
S5-1
1/2W
S
NO.
1/2W
ISSUE
DATE
SPEAKER CIRCUIT(S3)
C
10K
C
S3-8
C
S3-7
C
S3-6
C
S3-5
C
S3-4
S3-3
C
S3-1
S3-2
S
75
15
C
WP
A2:2-4
A2:2-3
15
15
P
CHANNEL 2 (A2:2)
C
A2:2-2
A2:2-1
A
M
D
75
75
C
C
A2:1-8
75
75
75
C
C
A2:1-7
75
A2:1-6
A2:1-5
75
C
A2:1-4
A2:1-3
75
CHANNEL 1 (A2:1)
C
M1-27
A2:1-1
A2:1-2
D
P
P
M1-28
M1-29
A
2ND FLOOR PE BUILDING
2ND FLOOR PE BUILDING
P
2W
2W
2W
2W
2W
2W
2W
2W
2W
2W
SPEAKER CIRCUIT(S4)
M
10K
S4-10
S4-9
S4-8
S4-7
S4-6
S4-5
S4-4
S4-3
S4-2
S4-1
S
1/2W
1/2W
1/4W
1/2W
1/2W
1/2W
1/2W
1/2W
1/4W
1/2W
1/2W
1/4W
1/2W
1/2W
1/4W
1/4W
1/4W
1/4W
6.8K
1/4W
1/4W
SPEAKER CIRCUIT(S2)
E
10K
S2-20
S2-19
S2-18
1/2W
1/2W
C
10K
S1-19
S2-17
1/4W
C
S1-18
S2-16
S2-15
1/4W
1/4W
C
S1-17
S2-14
S2-13
1/2W
1/2W
C
S1-16
S1-15
S2-12
1/2W
C
S1-14
S1-13
S2-11
1/2W
C
S1-12
S2-10
S2-9
S2-8
1/2W
1/2W
S2-7
1/2W
1/2W
C
C
S1-11
S1-10
S2-6
1/2W
C
S1-9
S1-8
S2-5
1/2W
C
S1-7
S1-6
S2-4
S2-3
1/2W
C
1/2W
C
S1-5
S2-2
S1-3
135
C
WG
S
135
WG
WG
A1:3-2
P
P
P
M1-22
M1-21
M1-20
M1-19
C
135
A1:3-3
A1:3-4
P
WF
VS
AIM
AIM
M1-18
M1-17
E
P
P
P
P
M1-16
M1-15
M1-14
M1-13
M1-12
M
SPEAKER CIRCUIT(S1)
S1-1
S1-2
135
S
1/2W
1/2W
C
S1-4
S2-1
6.8K
M1-1
P
P
P
M1-2
M1-3
M1-4
AIM
M1-5
M1-6
AOM
M1-7
POWER
MONITOR
CHANNEL 3 (A1:3)
AOM
M1-8
M1-9
PRIMARY
RECALL
ALTERN
RECALL
AOM
AOM
M1-10
M1-11
HAT
FLASH
SHUNT
TRIP
WG
A1:3-1
A
15
F
15
C
A1:2-19
15
C
A1:2-18
A1:2-9
75
C
A1:2-17
30
15
C
C
WP
A1:2-14
A1:2-15
A1:2-16
30
C
30
15
JB
JB
C
A1:2-12
A1:2-13
15
15
A1:2-11
30
C
A1:2-10
A1:2-9
C
A1:2-8
75
30
C
JB
C
WP
A1:2-6
A1:2-7
15
A1:2-4
A1:2-5
15
15
15
C
C
C
A1:2-3
CHANNEL 2 (A1:2)
F
A,S
A1:2-1
A1:2-2
CHANNEL 3 (A2:3)
A
A1:1-18
30
30
75
30
C
C
C
C
A1:1-17
A1:1-16
A1:1-15
75
A1:1-14
A1:1-13
75
30
75
C
C
C
A1:1-12
A1:1-11
75
30
75
WP
A1:1-10
WP
A1:1-9
A1:1-8
A1:1-7
30
30
30
30
30
15
110
C
C
C
C
C
C
C
A1:1-6
A1:1-5
A1:1-4
A1:1-3
A1:1-2
CHANNEL 1 (A1:1)
M
A1:1-1
LIM
A
1
M1-31
FIBER
DATA JACK
4100ES
TRANSMITTER
G
TO EXISTING CAMPUS NETWORK
FIBER
Y
FUTURE
TO WELLNESS CENTER
VIA PULL BOX AT
RESTROOM BUILDING
TO/FROM CAMPUS
FA NETWORK
G
FROM EXISTING CAMPUS NETWORK
Y
ARCHITECT'S STAMP
120 VOLT AC
APPROVAL
THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO LPAS, INC. AND IS FURNISHED FOR THE
PURPOSES OF REVIEW, BIDDING OR CONSTRUCTION OF THE PROJECT LISTED IN THE JOB TITLE BOX ABOVE
AND SHALL NOT BE USED FOR ANY OTHER PURPOSE OR RELEASED TO ANY OTHER PARTY WITHOUT THE
WRITTEN CONSENT OF LPAS, INC. INFOMATION CONTAINED HEREIN IS AN INSTRUMENT OF PROFESSIONAL
SERVICES AND SHALL REMAIN THE PROPERTY OF LPAS, INC. ALL RIGHTS RESERVED COPYRIGHT © 2009.
CAT5 CABLE ETHERNET DROP
TERMINATE W/RJ-45 FEMALE JACK
THIS DRAWING IS NOT FINAL OR TO BE USED FOR CONSTRUCTION UNTIL IT IS SIGNED BY THE ARCHITECT
AND ENGINEER.
1ST FLOOR PE BUILDING
1ST FLOOR PE BUILDING
H
H
CONSULTANT
2014-0174
Joe Ripp
J
J
J
AL
AT
EL
L
E CT RICA N
E O
OR
F CAL I F
IA
NO SCALE
ON LA
AS
No. E16806
ST
717 Market Street
Suite 500
San Francisco, CA 94103
TEL
415.489.7240
FAX
415.489.7289
www.interfaceengineering.com
F E S S I ON
I NE ER
E N G I N E E R I N G
PRO
U
1 ONE-LINE DIAGRAM - FIRE ALARM
D
ENG
INTERFACE
RE
CONTACT
R EG I S T E
PROJECT
ONE-LINE DIAGRAM - FIRE
ALARM
PROJECT NO: 1089-0001
DATE: 1.12.2015
K
K
SHEET NO:
FA4.01
12
11
10
9
8
7
6
5
4
3
2
1
DSA SUBMITTAL
12
11
10
9
8
7
6
FROM EXISTING
CAMPUS NETWORK
5
J2
U1
3
2
1
SYSTEM CONDUIT, 3/4" MIN. (2" SHOWN)
REFER TO MOUNTING DETAIL FOR TYP.
CONDUIT PENETRATION LOCATIONS
TO EXISTING
CAMPUS NETWORK
J2
4
U1
A
A
U3
U4
U3
DO NOT LOCATE POWER-LIMITED WIRING IN THE SHADED AREAS
OF THE BACKBOX, THIS AREA IS RESERVED FOR NON-POWER
LIMITED CIRCUITRY SUCH AS AC POWER, BATTERIES AND CITY
CONNECTION.
U4
24
4100-6057
FIBER
OPTION BD.
J1
1
2
39
40
RCV
4100-6057
FIBER
OPTION BD.
1
2
J1
39
40
XMIT
TO LCD ANNUNCIATOR LOBBY 101
4100-6078
DAUGHTER CARD
INSTALLED IN SLOT J1
FOR NETWORK INTERFACE
CA
A
FERRITE BEAD
TB3
SHLD
RUI A+
RUI A-
RTS
RCV
RUI B-
XMIT
R-
GND
OV-1
R+
RSRVD
B+
B+ BIDNAC 3
B-
AUX
POWER
+24 OV
A
TO 1ST FLOOR GYM (A1:3)
CLICK HERE
TO ADJUST
CH3 CKTS
CLICK HERE
TO ADJUST
CH2 CKTS
SAN JOSE CITY
COLLEGE
NETWORK/RS232 DAUGHTER CARD
CPU DAUGHTER CARD
1
2
4
6
8
5
16
4
32
3
64
2
9600/OFF
1
P7
ENHANCED TA POWER SUPPLY
120VAC 60Hz
7
P6
C
SAN JOSE, CALIFORNIA
CA
SW1
SW4
8/OFF
7
6
5
4
3
2
1
PHYSICAL EDUCATION BUILDING AND
RENOVATED LAB BUILDING
P
8
Lamp
Test
CLICK HERE
TO ADJUST
CH1 CKTS
B-
7
Auto
B+ BIDNAC 2
6
Off
Disarm
Next
B+
5
Disable
P4
OV
P5
RUI
B-
4
On
Arm
24V
B+ BIDNAC 1
B
TB4
3
Menu
Enable
MOUNTS ON
BRACKET
P3
Previous
TB3
TB2
TO 1ST FLOOR (A1:2)
2
More
Info
TB1
8
P8
COMM
P2
Event
Time
5
1
P1
4
CPU MOTHERBOARD
4100-6052
EVENT
REPORTING
DACT
System
Reset
3
ON
Alarm
Silence
2
NETWORK
1 2 3
RING
RING2 HOUSE 2
Trouble
Ack
1
B+
P6
TIP2
Supv
Ack
5
RS232
TIP
HOUSE 2
Priority 2
Ack
Alarm Silenced
AC Power
4
RUI B+
3
CTS
2
GND
1
+
RING
RING1 HOUSE 1
Fire Alarm
Ack
SYSTEM WARNINGS
Supervisory
Trouble
A
TB2
-
TIP
HOUSE 1 TIP1
B
ALARMS
Fire Alarm Priority 2 Alarm
TO 1ST FLOOR (A1:1)
P7
POWER
C
IDNet+
250 DEVICES
SW3
P4
OV-2
GND
L-
RSRVD
24C
PIEZO
GND
RCV
RTS
XMIT
CTS
RUI CONNECTOR
RUI CONNECTOR
4100 COMM
P3
5
4
3
2
RECT (+)
NO.
IDNet B+
P2
SW1
SHLD
R
RS232
IDNet B-
P5
P5
1 2 3
RECT (-)
SHIELD JUMPER
P1
IDNet A-
CLICK HERE
TO ADJUST
IDNet CKT
IDNet A+
L+
P4
RSRVD
NETWORK
SW2
P6
EARTH FAULT
JUMPER
1
ISSUE
DATE
BTRY (+)
TB1
BTRY (-)
TB1
P1
M
FERRITE BEAD
TO IDNET (M1)
A
TO 2ND FLOOR (A2:1)
A
TO 2ND FLOOR (A2:2)
4
3
A+
A-
+
-
2
1
B-
5
D
PRIMARY2
STYLE 4
DAR
DAR
PRIMARY ONLY
SECONDARY
4100-9621/-1311
DIGITAL AUDIO
CONTROLLER
5
6
7
CA
8
TO WELLNESS CENTER (A2:3)
P4
8
32
64
9600/OFF
INPUT OPTION CARD
PORT 2
16
SW1
MESSAGE MEMORY EXPANSION
4100-1241 8 MINUTE MESSAGE EXPANSION MODULE
4
1
G
3
4
Label
Label
Label
2
2
E
G
1
2
P7
R
Label
Label
Label
A
CLICK HERE
TO ADJUST
CH3 CKTS
1
3
G
ON
SW1
1
P6
8
R
AUX
POWER
+24 OV
4100-5311
ENHANCED TA POWER SUPPLY
120VAC 60Hz
7
Label
Label
Label
P4
P5
B-
P
6
OV
INPUT OPTION CARD
PORT 1
5
24V
B+ BIDNAC 3
CLICK HERE
TO ADJUST
CH2 CKTS
4
P3
G
B+
3
R
B-
2
P2
Label
Label
Label
B+ BIDNAC 2
P6
1
P1
G
B+
TB4
ON
R
5
R
4
G
6
Label
Label
Label
B-
CLICK HERE
TO ADJUST
CH1 CKTS
7
G
B+ BIDNAC 1
8
R
Label
Label
Label
TB3
TB2
B+
Label
Label
Label
Label
Label
TB1
+
D
6
-
TB2
B+
P11
CA
IDNet+
250 DEVICES
R
E
P1
Label
Label
Label
R
LOCAL SPEAKER/MIC
RECT (-)
SHIELD JUMPER
P1
G
SHLD
PTT (RED)
MIC (WHT)
RTN (BLK)
MIC (WHT)
2
1
IDNet B+
3
4
SHLD
4
5
IDNet B-
TP SPEAKER CIRCUIT S3
TO SPEAKER CIRCUIT S2
TO SPEAKER CIRCUIT S1
5
IDNet A-
56
IDNet A+
REMOTE MICROPHONE
3
2
1
RECT (+)
EARTH FAULT
JUMPER
BTRY (+)
TB1
BTRY (-)
TB1
S
10K
S
10K
10K
TO SPEAKER CIRCUIT S4
TO SPEAKER CIRCUIT S5
TO SPEAKER CIRCUIT S6
F
F
B-
SHLD
B+
B-
SHLD
B+
B-
NAC
NAC
NAC
CLICK HERE
TO ADJUST
CKT SHIELDS
1
CLICK HERE
TO ADJUST
510X CKTS
2
3
4
NAC
5
6
7
NAC
NAC
CLICK HERE
TO ADJUST
CKT SHIELDS
CLICK HERE
TO ADJUST
CKT WIRING
8
B-
8
B+
7
B-
6
SHLD
5
B+
4
B-
3
TB1
SHLD
2
1 2 3 4 5 6 7 8 9 10 11 12
B+ B- A+ A- B+ B- A+ A- B+ B- A+ ANAC 1
NAC 2
NAC 3
B+
1
B+
TB1
CLICK HERE
TO ADJUST
CKT WIRING
P1
P2
P3
24V
OV
P4
P5
P6
SW1
P7
1
CA
P1
2
3
4
5
6
G
4100-1327
FLEX 50 WATT
DIGITAL AMP
70V RMS
8
DIGITAL AUDIO DECODER
DIGITAL AUDIO DECODER
7
4100-5101
XPS POWER SUPPLY
120VAC 60Hz
AUX
POWER
CA
OV
-
G
4100-1327
FLEX 50 WATT
DIGITAL AMP
70V RMS
+24
+
ARCHITECT'S STAMP
CA
APPROVAL
TB2
CONNECT TO 120VAC 60HZ
THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO LPAS, INC. AND IS FURNISHED FOR THE
PURPOSES OF REVIEW, BIDDING OR CONSTRUCTION OF THE PROJECT LISTED IN THE JOB TITLE BOX ABOVE
AND SHALL NOT BE USED FOR ANY OTHER PURPOSE OR RELEASED TO ANY OTHER PARTY WITHOUT THE
WRITTEN CONSENT OF LPAS, INC. INFOMATION CONTAINED HEREIN IS AN INSTRUMENT OF PROFESSIONAL
SERVICES AND SHALL REMAIN THE PROPERTY OF LPAS, INC. ALL RIGHTS RESERVED COPYRIGHT © 2009.
NEUTRAL
MOUNTS TO BACKBOX
BATTERY
P4
P3
P2
-
P1
+
AC
-
+
THIS DRAWING IS NOT FINAL OR TO BE USED FOR CONSTRUCTION UNTIL IT IS SIGNED BY THE ARCHITECT
AND ENGINEER.
H
H
CONSULTANT
J
J
J
ON LA
AS
AL
No. E16806
AT
EL
L
E CT RICA N
E O
OR
F CAL I F
IA
ST
717 Market Street
Suite 500
San Francisco, CA 94103
TEL
415.489.7240
FAX
415.489.7289
www.interfaceengineering.com
F E S S I ON
I NE ER
E N G I N E E R I N G
PRO
U
INTERFACE
50 Ah BATTERY
2081-9296
D
ENG
50 Ah BATTERY
2081-9296
2014-0174
Joe Ripp
RE
CONTACT
R EG I S T E
PROJECT
CONTROL PANEL DIAGRAM
- FIRE ALARM
PROJECT NO: 1089-0001
DATE: 1.12.2015
K
K
SHEET NO:
FIRE ALARM CONTROL PANEL
FA5.01
CABINET # 1 - FIRST FLOOR
RECEPTION AREA B230
SCALE: NTS
12
11
10
9
8
7
6
5
4
3
2
1
DSA SUBMITTAL
12
11
10
9
8
7
6
5
4
3
2
1
A
A
4100 FACP 1ST FLOOR ELECTRICAL ROOM 136 - EPS-1 CIRCUIT SUMMARY & VOLTAGE DROP
4100 FACP 1ST FLOOR ELECTRICAL ROOM 136 4100es FACP
Standby
B
Module
Qty
Description
Total
Standby
Current
Alarm
Current
Total
Alarm
Channel
C
4100-9311
1
4100 CONFIG. DOMESTIC 120V
0.4250
0.4250
0.7350
0.7350
4100-1327
2
DIGITAL FLEX 50W AMP W/3 NACS - 70V
0.0850
0.1700
2.2700
4.5400
4100-5101
1
EXPANSION PWR SUPPLY (XPS) - 120VAC 60HZ
0.0500
0.0500
0.0500
0.0500
4100-6057
2
NETWORK MEDIA CARD FIBER OPTIC
0.0250
0.0500
0.0250
0.0500
4100-5311
1
ENHANCED POWER SUPPLY, 3 CHANNELS, IDNet1+, 120V
0.2250
0.2250
0.4900
0.4900
4100-6078
1
NETWORK IF CARD, MODULAR
0.0460
0.0460
0.0460
0.0460
4100-9621
1
BASIC AUDIO WITH MICROPHONE - DIGITAL
0.0750
0.0750
0.0820
0.0820
4100-6052
1
EVENT REPORTING DACT
0.0300
0.0300
0.0400
0.0400
4100-1241
1
MESSAGE EXPANSION BOARD - 8 MINUTES
0.0020
0.0020
0.0170
0.0170
4100-1288
1
64/64 LED/SWITCH CONTROLLER
0.0200
0.0200
0.0200
0.0200
4100-1279
13
2" BLANK DISPLAY MODULE
0.0000
0.0000
0.0000
0.0000
*
4100-0634
1
POWER DISTRIBUTION MODULE 120V
0.0000
0.0000
0.0000
0.0000
4100-2320
1
AUDIO EXPANSION BAY KIT
0.0000
0.0000
0.0000
0.0000
4100-0636
1
BOX TO BOX HARNESS KIT
0.0000
0.0000
0.0000
0.0000
4100-1284
1
8 SW, 16 RED/GREEN LED MODULE
0.0000
0.0000
0.0240
0.0240
Panel Totals
1.0930
D
13
ADDRESSABLE SINGLE ACTION MANUAL STATION
*
4090-9001
3
IDNET SUPERVISED IAM
*
4090-9002
4
IDNET RELAY IAM
*
4098-9714
24
TRUEALARM PHOTO SMOKE SENSOR
4098-9733
2
TRUEALARM HEAT SENSOR
4098-9756
3
TRUEALARM DUCT SMOKE SENSOR W/ RELAY OUTPUT
*
4098-9792
26
TRUEALARM SENSOR BASE
*
Branch
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Device Current Draw on the IDNet Addressable Channel(s) is included in
the Battery Selection Set below.
Device #
A1:1-1
A1:1-2
A1:1-3
A1:1-4
A1:1-5
A1:1-6
A1:1-7
A1:1-8
A1:1-9
A1:1-10
A1:1-11
A1:1-12
A1:1-13
A1:1-14
A1:1-15
A1:1-16
A1:1-17
A1:1-18
From
PANEL
A1:1-1
A1:1-2
A1:1-3
A1:1-4
A1:1-5
A1:1-1
A1:1-7
A1:1-7
A1:1-9
A1:1-9
A1:1-11
A1:1-12
A1:1-13
A1:1-14
A1:1-15
A1:1-16
A1:1-17
Totals:
ENCAPSULATED RELAY PAM-SD
0.0000
0.0000
0.0150
0.0450
4098-9756
3
TRUEALARM DUCT SMOKE SENSOR W/ RELAY OUTPUT
0.0030
0.0090
0.0150
0.0450
4906-9204
3
ADDRESSABLE CEILING MNT MC V/O, WHITE
15
0.0002
0.0006
0.0600
0.1800
4906-9253
1
ADDRESSABLE WALL MNT MC S/V, WHITE
75
0.0002
0.0002
0.1370
0.1370
4906-9254
3
ADDRESSABLE CEILING MNT S/V 25V/70VRMS WHITE
110
0.0002
0.0006
0.2400
0.7200
4906-9254
15
ADDRESSABLE CEILING MNT S/V 25V/70VRMS WHITE
15
0.0002
0.0030
0.0600
0.9000
4906-9254
13
ADDRESSABLE CEILING MNT S/V 25V/70VRMS WHITE
30
0.0002
0.0026
0.0920
1.1960
4906-9254
17
ADDRESSABLE CEILING MNT S/V 25V/70VRMS WHITE
75
0.0002
0.0034
0.1800
3.0600
49VO-WWFO-BA
6
VO, WALL MT, WHITE, FIRE LABEL, WEATHERPROOF
WP75
0.0008
0.0048
0.2120
1.2720
49VO-WWF
4
VO, WALL MT, WHITE, FIRE LABEL
135
0.0008
0.0032
0.0290
0.1600
0.6400
8.2890
Distance
(Feet)
30
37
18
24
27
25
30
46
17
46
21
117
17
39
25
39
25
21
604 Ft.
Peripheral Totals
Added Current for EPS Conversion of 24 to 29 Volt IDNac Devices
RUI Totals
0
Address Totals
49 Addresses
Total Standby
* Device Address current draw included below (See Additional Current Draws):
0.0000
3.0336
0.0000
0.0000
0.0392
0.0490
1.1612
Total Alarm
Standby
Standby
Alarm
Alarm
Current
Total
Current
Total
Branch
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
17.4656
F
EPS-1
EPS-2
0.7040
0.2320
5.6300
4.1880
XPS-3
0.1950
4.5650
1.1310
14.3830
0.0000
3.0336
Sub Total
Additional Current Draws:
Current for Conversion of Battery Voltage to 29 volt EPS IDNAC Devices
MAPNET/IDNet Device Address Communication Current
Spare addressable point capacity
Standby Time =
Alarm Time =
49
0%
24
15
0
Hrs
Min
x 0.000800
= 0.0392
Sub Total
1.1702
Total
= 0.0000
1.1702
x 0.0008
0%
+
20%
+
Minimum Battery Required 2081-9296 50AH (2x)
Battery Supplied 2081-9296 50AH (2x)
From
PANEL
A1:2-1
A1:2-2
A1:2-3
TAP1
A1:2-4
A1:2-4
A1:2-6
A1:2-7
TAP1
A1:2-9
A1:2-10
A1:2-9
TAP2
A1:2-12
TAP3
A1:2-13
TAP3
TAP3
TAP2
A1:2-17
A1:2-18
Totals:
= 0.0490
Spare
Capacity
604
663
394
23%
49%
79%
B
SAN JOSE CITY
COLLEGE
PHYSICAL EDUCATION BUILDING AND
RENOVATED LAB BUILDING
Wire Res. Per Ft.
Min. Device Voltage:
0.0019
23.vdc
@ 75° Celsius
Voltage
Drop
Voltage
SAN JOSE, CALIFORNIA
29vdc
Device
Draw
0.2400
0.0600
0.0920
0.0920
0.0920
0.0920
0.0920
0.2120
0.0920
0.2120
0.1800
0.0920
0.1800
0.1370
0.0920
0.1800
0.0920
0.0920
Class B Calculations
Current
at Device
2.321
0.428
0.368
0.276
0.184
0.092
1.653
0.212
1.349
0.212
1.045
0.865
0.773
0.593
0.456
0.364
0.184
0.092
0.269
0.061
0.026
0.026
0.019
0.009
0.191
0.038
0.089
0.038
0.085
0.391
0.051
0.089
0.044
0.055
0.018
0.007
at Device
28.731
28.670
28.645
28.619
28.600
28.591
28.540
28.502
28.451
28.414
28.367
27.976
27.925
27.836
27.792
27.737
27.719
27.712
C
Branch
% Drop
Branch 1: 4.44%
NO.
ISSUE
DATE
D
Distance
(Feet)
239
42
48
26
25
14
18
15
20
34
12
16
31
14
4
12
9
9
14
26
16
19
663 Ft.
20.7%
12ga
0.0019
23.vdc
@ 75° Celsius
Voltage
Drop
Voltage
29vdc
Candela
15cd
15cd
15cd
PID
4906-9254
4906-9254
4906-9254
JBOX
4906-9204
4906-9254
49VO-WWFO-BA
4906-9254
4906-9254
4906-9254
4906-9204
4906-9254
JBOX
4906-9204
JBOX
4906-9254
4906-9254
4906-9254
49VO-WWFO-BA
4906-9254
4906-9254
4906-9254
Wire Res. Per Ft.
Min. Device Voltage:
15cd
15cd
WP75
30cd
30cd
15cd
15cd
30cd
15cd
15cd
15cd
15cd
WP75
15cd
15cd
15cd
Device
Draw
0.0600
0.0600
0.0600
0.0000
0.0600
0.0600
0.2120
0.0920
0.0920
0.0600
0.0600
0.0920
0.0000
0.0600
0.0000
0.0600
0.0600
0.0600
0.2120
0.0600
0.0600
0.0600
Class B Calculations
Current
at Device
1.540
1.480
1.420
1.360
0.516
0.060
0.396
0.184
0.092
0.844
0.152
0.092
0.632
0.452
0.392
0.120
0.060
0.060
0.212
0.180
0.120
0.060
1.421
0.240
0.263
0.136
0.050
0.003
0.028
0.011
0.007
0.111
0.007
0.006
0.076
0.024
0.006
0.006
0.002
0.002
0.011
0.018
0.007
0.004
at Device
27.579
27.339
27.076
26.940
26.890
26.887
26.862
26.852
26.845
26.829
26.822
26.816
26.753
26.729
26.723
26.717
26.715
26.721
26.711
26.735
26.728
26.723
Branch
% Drop
E
Branch 1: 7.89%
F
17.4656
x 0.001
A1:3
= 0.0000
17.4656
Distributed Load Voltage Drop
Allowable % Drop:
Wire Gauge:
Starting Voltage:
0.0000
Branch
1
1
1
1
32.4512
Battery Discharge Factor =
Wire
Length
Distributed Load Voltage Drop
= 28.0848 Standby Ah
= 4.3664 Alarm Ah
32.4512
x 1.1702
0.25 x 17.4656
G
Additional Spare Battery Capacity =
x 0.001000
Device #
A1:2-1
A1:2-2
A1:2-3
TAP1
A1:2-4
A1:2-5
A1:2-6
A1:2-7
A1:2-8
A1:2-9
A1:2-10
A1:2-11
TAP2
A1:2-12
TAP3
A1:2-13
A1:2-14
A1:2-15
A1:2-16
A1:2-17
A1:2-18
A1:2-19
20.7%
12ga
Candela
110cd
15cd
30cd
30cd
30cd
30cd
30cd
WP75
30cd
WP75
75cd
30cd
75cd
75cd
30cd
75cd
30cd
30cd
Allowable % Drop:
Wire Gauge:
Starting Voltage:
2. Backup Amplifier assumes Main Amplifier alarm current on failure.
Battery Set #1 (Cabinet/Charger #1)
Select ALL Power Supplies on this battery set:
PID
4906-9254
4906-9254
4906-9254
4906-9254
4906-9254
4906-9254
4906-9254
49VO-WWFO-BA
4906-9254
49VO-WWFO-BA
4906-9254
4906-9254
4906-9254
4906-9253
4906-9254
4906-9254
4906-9254
4906-9254
A1:2
Notification Appliances
E
Unit
Load*
18
19
4
Notification SLC Distributed Load Voltage Drop
Miscellaneous Peripheral Devices That May Require System Power
3
4.44%
7.89%
2.13%
Allowable % Drop:
Wire Gauge:
Starting Voltage:
6.0940
4098-9843
% Drop
A1:1
IDNet Addressable Devices (SLC)
4099-9004
1ST FLOOR
1ST FLOOR
1ST FLOOR GYM
A1:1
A1:2
A1:3
Panel Equipment
Alarm
Current
2.321A
1.540A
0.640A
Description
6.4902
38.9414
Device #
A1:3-1
A1:3-2
A1:3-3
A1:3-4
From
PANEL
A1:3-1
A1:3-2
A1:3-3
Totals:
Distance
(Feet)
105
55
180
54
394 Ft.
20.7%
12ga
0.0019
23.vdc
@ 75° Celsius
29vdc
Candela
135cd
135cd
135cd
135cd
PID
49VO-WWF
49VO-WWF
49VO-WWF
49VO-WWF
Wire Res. Per Ft.
Min. Device Voltage:
Device
Draw
0.1600
0.1600
0.1600
0.1600
Class B Calculations
Current
at Device
0.640
0.480
0.320
0.160
G
Voltage
Drop
0.259
0.102
0.222
0.033
Voltage
at Device
28.741
28.639
28.416
28.383
Branch
% Drop
Branch 1: 2.13%
ARCHITECT'S STAMP
APPROVAL
THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO LPAS, INC. AND IS FURNISHED FOR THE
PURPOSES OF REVIEW, BIDDING OR CONSTRUCTION OF THE PROJECT LISTED IN THE JOB TITLE BOX ABOVE
AND SHALL NOT BE USED FOR ANY OTHER PURPOSE OR RELEASED TO ANY OTHER PARTY WITHOUT THE
WRITTEN CONSENT OF LPAS, INC. INFOMATION CONTAINED HEREIN IS AN INSTRUMENT OF PROFESSIONAL
SERVICES AND SHALL REMAIN THE PROPERTY OF LPAS, INC. ALL RIGHTS RESERVED COPYRIGHT © 2009.
THIS DRAWING IS NOT FINAL OR TO BE USED FOR CONSTRUCTION UNTIL IT IS SIGNED BY THE ARCHITECT
AND ENGINEER.
H
H
CONSULTANT
2014-0174
Joe Ripp
J
ON LA
AS
AL
I NE ER
J
J
F E S S I ON
No. E16806
AT
EL
L
E CT RICA N
E O
OR
F CAL I F
IA
ST
717 Market Street
Suite 500
San Francisco, CA 94103
TEL
415.489.7240
FAX
415.489.7289
www.interfaceengineering.com
PRO
U
E N G I N E E R I N G
D
ENG
INTERFACE
RE
CONTACT
R EG I S T E
PROJECT
CALCULATIONS - FIRE
ALARM
PROJECT NO: 1089-0001
DATE: 1.12.2015
K
K
SHEET NO:
FA6.01
12
11
10
9
8
7
6
5
4
3
2
1
DSA SUBMITTAL
12
11
10
9
8
7
6
5
4
3
2
1
A
A
IDNET CHANNEL M1
Address
Device Type
4100 FACP 1ST FLOOR ELECTRICAL ROOM 136 - EPS-2 CIRCUIT SUMMARY & VOLTAGE DROP
Alarm
Current
1.592A
0.392A
1.714A
Description
Channel
2ND FLOOR
2ND FLOOR
WELLNESS CENTER
A2:1
A2:2
A2:3
% Drop
3.15%
0.67%
7.12%
A2:1
B
Device #
A2:1-1
A2:1-2
A2:1-3
A2:1-4
A2:1-5
A2:1-6
A2:1-7
A2:1-8
From
PANEL
A2:1-1
A2:1-2
A2:1-3
A2:1-1
A2:1-5
A2:1-6
A2:1-7
Totals:
C
Distance
(Feet)
103
26
51
24
51
29
30
29
343 Ft.
20.7%
12ga
Spare
Capacity
343
215
479
47%
87%
43%
Wire Res. Per Ft.
Min. Device Voltage:
0.0019
23.vdc
@ 75° Celsius
Device
Draw
0.2400
0.2400
0.1800
0.1800
0.1800
0.1800
0.1800
0.2120
Class B Calculations
Current
at Device
1.592
0.600
0.360
0.180
0.752
0.572
0.392
0.212
Voltage
Drop
Voltage
Branch
% Drop
at Device
28.367
28.307
28.236
28.219
28.219
28.155
28.110
28.086
0.633
0.060
0.071
0.017
0.148
0.064
0.045
0.024
Branch 1: 3.15%
Device #
TAP1
A2:2-1
A2:2-2
A2:2-3
A2:2-4
From
PANEL
TAP1
A2:2-1
TAP1
A2:2-3
Totals:
Distance
(Feet)
84
18
41
41
31
215 Ft.
PID
JBOX
4906-9254
4906-9254
4906-9254
49VO-WWFO-BA
20.7%
12ga
0.0019
23.vdc
@ 75° Celsius
29vdc
Candela
15cd
15cd
15cd
WP75
Device
Draw
0.0000
0.0600
0.0600
0.0600
0.2120
Class B Calculations
Current
at Device
0.392
0.120
0.060
0.272
0.212
Voltage
Drop
Voltage
Branch
% Drop
at Device
28.873
28.865
28.855
28.830
28.804
0.127
0.008
0.009
0.043
0.025
Branch 1: 0.67%
D
A2:3
Distributed Load Voltage Drop
Allowable % Drop:
Wire Gauge:
Starting Voltage:
20.7%
12ga
Wire Res. Per Ft.
Min. Device Voltage:
0.0019
23.vdc
1 2 3 4 5 6 7 8
PHOTO
SMOKE
1ST FLR ELEC 136
X
M1-2
ADRPUL
PULL
1ST FLR ELEC 136
X
M1-3
ADRPUL
PULL
1ST FLR TICKETS/CONCESSION 124
X
X
M1-4
ADRPUL
PULL
1ST FLR MACH RM 120
X
X
M1-5
HEAT
HEAT
1ST FLR MACH RM 120
X
M1-6
PHOTO
SMOKE
1ST FLR MACH RM 120
X
M1-7
IAM
SUPERV
1ST FLR MACH RM 120 POWER MONITOR
M1-8
RIAM
PRIMARY
M1-9
RIAM
M1-10
RIAM
RIAM
@ 75° Celsius
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
1ST FLR MACH RM 120 PRIMARY RECALL
X
X
X
ALTERN
1ST FLR MACH RM 120 ALTERN RECALL
X
X
X
RELAY
1ST FLR MACH RM 120 HAT FLASH
X
1ST FLR MACH RM 120 SHUNT TRIP
X
RELAY
PHOTO
SMOKE
M1-13
ADRPUL
M1-14
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
1ST FLR ELEV E1.1 LOBBY
X
PULL
1ST FLR HALL 137
X
ADRPUL
PULL
1ST FLR EAST CORRIDOR 137
X
M1-15
ADRPUL
PULL
1ST FLR FOOTBALL LOCKER RM 146
X
X
X
X
M1-16
ADRPUL
PULL
1ST FLR SOUTH CORRIDOR 150
X
X
X
X
X
X
M1-17
IAM
SO
1ST FLR LAUNDRY 159
X
M1-18
IAM
WATER
1ST FLR LAUNDRY 159
X
M1-19
ADRPUL
PULL
1ST FLOOR TRAINING ROOM138
X
X
M1-20
ADRPUL
PULL
1ST FLOOR MULTIPURPOSE 141
X
X
X
M1-26
RPHOTO
DUCT
M1-27
PHOTO
SMOKE
X
X
X
X
X
X
X
X
X
X
X
X
X
M1-24
X
2ND FLR FITNESS CENTER 202 AHU-3
X
X
X
X
DUCT
X
X
X
M1-23
RPHOTO
X
X
M1-22
2ND FLR FITNESS CENTER 202 AHU-2
X
2ND FLR ELEV E1.1 LOBBY
X
M1-28
ADRPUL
PULL
2ND FLR CORRIDOR 201
X
M1-29
ADRPUL
PULL
2ND FLR CORRIDOR 201
X
M1-30
RPHOTO
DUCT
2ND FLR AHU-1
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
M1-31
X
X
X
X
X
M1-32
X
X
X
X
X
M1-33
X
X
X
X
X
X
M1-34
X
M1-35
X
X
M1-36
X
X
M1-37
X
M1-38
X
M1-39
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
M1-40
X
X
X
M1-248
X
X
X
X
X
M1-249
THRU
X
SPARE
M1-250
29vdc
X
X
M1-12
M1-25
Wire Res. Per Ft.
Min. Device Voltage:
Location Description
M1-21
Distributed Load Voltage Drop
Allowable % Drop:
Wire Gauge:
Starting Voltage:
Point Type
M1-1
M1-11
29vdc
Candela
110cd
110cd
75cd
75cd
75cd
75cd
75cd
WP75
PID
4906-9254
4906-9254
4906-9254
4906-9254
4906-9254
4906-9254
4906-9254
49VO-WWFO-BA
A2:2
Branch
1
1
1
1
1
Wire
Length
Notification SLC Distributed Load Voltage Drop
Allowable % Drop:
Wire Gauge:
Starting Voltage:
Branch
1
1
1
1
1
1
1
1
Unit
Load*
8
4
11
SWITCH SETTINGS
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
B
ON
ON
ON
ON
ON
SAN JOSE CITY
COLLEGE
ON
PHYSICAL EDUCATION BUILDING AND
RENOVATED LAB BUILDING
ON
ON
ON
ON
SAN JOSE, CALIFORNIA
ON
ON
ON
ON
C
ON
ON
ON
NO.
ISSUE
DATE
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
D
ON
ON
X
X
X
X
X
ON
X
X
X
X
X
ON
X
X
X
X
X
ON
NOTE: THE LABELS SHOWN ABOVE WILL BE USED FOR PROGRAMMING PURPOSES.
THE LABELS ARE BASED UPON INFORMATION SHOWN ON THE ARCHITECTURAL DRAWINGS.
ANY CHANGES TO THESE LABELS MUST BE NOTED ON THE SUBMITTAL REVIEW, PRIOR TO PROGRAMMING.
Branch
% Drop
at Device
27.677
27.576
27.425
27.293
27.247
27.156
27.088
27.027
26.983
26.955
26.934
27.059
POINTS SHOWN IN ITALIC TEXT REFER TO EXISTING DEVICES.
Branch 1: 7.12%
E
4100 FACP 1ST FLOOR ELECTRICAL ROOM 136 4100es FACP Speaker Db Loss Calculations
*Circuit Voltage = 70vrms [Et]
SPEAKER CIRCUIT DESCRIPTION
Amp #
Amp-1
Amp-1
Amp-1
Amp-2
Amp-2
Amp-2
F
1ST FLOOR
1ST FLOOR
2ND FLOOR
1ST FLOOR GYM
2ND FLOOR
WELLNESS CENTER
Amplifier
Wattage
Amp-1
Amp-2
50
50
IDNET CHANNEL M2
Address
Device Type
MAXIMUM -3 dB DROP
Watts
Used
20.W
27.75W
Alarm
Expansion
2.270A
2.270A
Card?
Yes
Yes
Avail.
Ckts.
6
6
Plan
Circuit
Number
S1
S2
S3
S4
S5
S6
Used
Ckts.
4
3
Speaker
Tap
.25 Watt
5
9
5
2
Speaker
Tap
.5 Watt
14
11
8
Speaker
Tap
1. Watt
Speaker
Tap
2. Watt
10
1
6
1
SWITCH SETTINGS
Point Type
Location Description
1 2 3 4 5 6 7 8
Total
Total
Wire
Est. Ckt.
Wire Res.
Circuit
Speaker
Speaker
Voltage
Watts
Actual
Max Allowable
M2-1
ADRPUL
PULL
1ST FLR WELLNESS CNTR VEST 10
X
Spkrs
per
Circuit
19
20
8
10
6
9
Watts
[P]
Gauge
Length
[D] in
Feet
Per Foot
[Rw]
Resistance
[Rl=2D*Rw]
Current
[I=P/Et]
Resistance
[Rs=Et/I]
At End
At End
dB Loss
[dB=Log10
Ckt. Length
M2-2
PHOTO
SMOKE
1ST FLR WELLNESS CNTR VEST 10
X
1ST FLR WELLNESS CNTR VEST 115
X
8.25 Watts
7.75 Watts
4. Watts
20. Watts
3.25 Watts
4.5 Watts
16ga
16ga
16ga
16ga
16ga
16ga
620
680
447
410
158
500
0.0049
0.0049
0.0049
0.0049
0.0049
0.0049
6.064
6.650
4.372
4.010
1.545
4.890
0.118
0.111
0.057
0.286
0.046
0.064
593.939
632.258
1225.000
245.000
1507.692
1088.889
[Es=(Et*Rs)
[Pe=(Es)
[ML=(0.414*Rs)
*2/Rs]
/(Rs+Rl)]
(Pe/P)*10]
/(2*Rw)]
69.293
8.084
-.09 db
25142
69.271
7.590
-.09 db
26764
69.751
3.972
-.03 db
51856
68.873
19.361
-.14 db
10371
69.928
3.243
-.01 db
63823
69.687
4.460
-.04 db
46094
M2-3
Ft.
Ft.
Ft.
Ft.
Ft.
Ft.
PHOTO
SMOKE
1ST FLR WELLNESS CNTR VEST 115
X
M2-5
PHOTO
SMOKE
1ST FLR WELLNESS CNTR TOILET 14
X
M2-6
PHOTO
SMOKE
1ST FLR WELLNESS CNTR TOILET 13
X
M2-7
HEAT
HEAT
1ST FLR WELLNESS CNTR JANITOR 12
X
H
PHOTO
SMOKE
MEZZANINE WELLNESS CNTR STORAGE 22
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
PHOTO
SMOKE
MEZZANINE WELLNESS CNTR MECH 24
M2-10
PHOTO
SMOKE
MEZZANINE WELLNESS CNTR EXERCISE LAB 16
X
M2-11
PHOTO
SMOKE
MEZZANINE WELLNESS CNTR EXERCISE LAB 16
X
X
M2-12
PHOTO
SMOKE
MEZZANINE WELLNESS CNTR EXERCISE LAB 16
X
X
M2-13
PHOTO
SMOKE
MEZZANINE WELLNESS CNTR EXERCISE LAB 16
X
SMOKE
X
X
M2-9
PHOTO
X
X
X
M2-14
G
PULL
M2-4
M2-8
%
Used
40.00%
55.50%
ADRPUL
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
MEZZANINE WELLNESS CNTR EXERCISE LAB 16
X
X
X
X
X
X
X
X
X
X
X
X
X
X
M2-15
PHOTO
SMOKE
MEZZANINE WELLNESS CNTR EXERCISE LAB 16
X
M2-16
PHOTO
SMOKE
MEZZANINE WELLNESS CNTR STORAGE 22
X
M2-17
PHOTO
SMOKE
MEZZANINE WELLNESS CNTR MECH 27
X
M2-18
PHOTO
SMOKE
MEZZANINE WELLNESS CNTR EXERCISE LAB 11
X
M2-19
PHOTO
SMOKE
MEZZANINE WELLNESS CNTR EXERCISE LAB 11
X
M2-20
PHOTO
SMOKE
MEZZANINE WELLNESS CNTR EXERCISE LAB 11
X
M2-21
PHOTO
SMOKE
MEZZANINE WELLNESS CNTR EXERCISE LAB 11
X
M2-22
PHOTO
SMOKE
MEZZANINE WELLNESS CNTR EXERCISE LAB 11
X
M2-23
PHOTO
SMOKE
MEZZANINE WELLNESS CNTR EXERCISE LAB 11
X
X
X
X
X
X
X
X
X
X
X
M2-24
X
X
X
M2-25
X
X
X
M2-26
X
M2-27
X
M2-28
X
M2-29
X
M2-30
X
M2-249
X
THRU
X
SPARE
M2-250
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
ON
ON
ON
F
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
ON
G
ON
ON
ON
ARCHITECT'S STAMP
ON
APPROVAL
ON
ON
THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO LPAS, INC. AND IS FURNISHED FOR THE
PURPOSES OF REVIEW, BIDDING OR CONSTRUCTION OF THE PROJECT LISTED IN THE JOB TITLE BOX ABOVE
AND SHALL NOT BE USED FOR ANY OTHER PURPOSE OR RELEASED TO ANY OTHER PARTY WITHOUT THE
WRITTEN CONSENT OF LPAS, INC. INFOMATION CONTAINED HEREIN IS AN INSTRUMENT OF PROFESSIONAL
SERVICES AND SHALL REMAIN THE PROPERTY OF LPAS, INC. ALL RIGHTS RESERVED COPYRIGHT © 2009.
ON
ON
ON
THIS DRAWING IS NOT FINAL OR TO BE USED FOR CONSTRUCTION UNTIL IT IS SIGNED BY THE ARCHITECT
AND ENGINEER.
ON
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
ON
X
X
X
X
ON
ON
ON
ON
H
CONSULTANT
NOTE: THE LABELS SHOWN ABOVE WILL BE USED FOR PROGRAMMING PURPOSES.
THE LABELS ARE BASED UPON INFORMATION SHOWN ON THE ARCHITECTURAL DRAWINGS.
ANY CHANGES TO THESE LABELS MUST BE NOTED ON THE SUBMITTAL REVIEW, PRIOR TO PROGRAMMING.
PROJECT
CONTACT
2014-0174
Joe Ripp
J
J
AL
No. E16806
ST
717 Market Street
Suite 500
San Francisco, CA 94103
TEL
415.489.7240
FAX
415.489.7289
www.interfaceengineering.com
ON LA
AS
I NE ER
E N G I N E E R I N G
F E S S I ON
U
INTERFACE
PRO
ENG
POINTS SHOWN IN ITALIC TEXT REFER TO EXISTING DEVICES.
D
AT
EL
E CT RICA N
E O
OR
F CAL I F
L
Totals:
15cd
75cd
75cd
75cd
75cd
1.323
0.101
0.152
0.131
0.046
0.091
0.068
0.061
0.044
0.028
0.021
0.029
Voltage
IA
PANEL
A2:3-1
A2:3-2
A2:3-3
A2:3-4
A2:3-5
A2:3-6
TAP1
A2:3-7
A2:3-8
A2:3-9
TAP1
Candela
75cd
75cd
75cd
75cd
75cd
15cd
PID
4906-9254
4906-9254
4906-9254
4906-9254
4906-9254
49VO-WWF
JBOX
49VO-WWF
4906-9254
4906-9254
4906-9254
4906-9254
Voltage
Drop
J
From
Class B Calculations
Current
at Device
1.714
1.534
1.354
1.174
0.994
0.814
0.767
0.587
0.540
0.360
0.180
0.180
RE
E
Device #
A2:3-1
A2:3-2
A2:3-3
A2:3-4
A2:3-5
A2:3-6
TAP1
A2:3-7
A2:3-8
A2:3-9
A2:3-10
A2:3-11
Device
Draw
0.1800
0.1800
0.1800
0.1800
0.1800
0.0470
0.0000
0.0470
0.1800
0.1800
0.1800
0.1800
R EG I S T E
Branch
1
1
1
1
1
1
1
1
1
1
1
1
Distance
(Feet)
200
17
29
29
12
29
23
27
21
20
30
42
479 Ft.
CALCULATIONS - FIRE
ALARM
PROJECT NO: 1089-0001
DATE: 1.12.2015
K
K
SHEET NO:
FA6.02
12
11
10
9
8
7
6
5
4
3
2
1
DSA SUBMITTAL
12
11
10
9
8
7
6
5
PRODUCT INFORMATION
FEATURES:
DETAIL 1 KEYNOTES
1
AIR HANDLING UNIT (AHU) STARTER/VFD.
1
AIR HANDLING UNIT (AHU) STARTER/VFD.
2
FIRE ALARM ADDRESSABLE RELAY. CONNECT TO EMERGENCY STOP
INPUT ON FAN CONTROLLER. PROGRAM TO STOP FAN ON ACTIVATION
OF ASSOCIATED SMOKE DETECTION. PROVIDE RELAY FOR EACH FAN
CONTROLLER.
2
FIRE ALARM ADDRESSABLE RELAY. CONNECT TO EMERGENCY STOP
INPUT ON FAN CONTROLLER. PROGRAM TO STOP FAN ON ACTIVATION
OF ASSOCIATED SMOKE DETECTION. PROVIDE RELAY FOR EACH FAN
CONTROLLER.
3
FIRE ALARM ADDRESSABLE DUCT SMOKE DETECTOR.
3
FIRE ALARM ADDRESSABLE AREA SMOKE DETECTION SYSTEM.
4
FIRE ALARM ADDRESSABLE RELAY. DIGITAL INPUT TO BAS TO INITIATE
ADDITIONAL AHU SHUT DOWN SEQUENCE.
4
FIRE ALARM ADDRESSABLE RELAY. DIGITAL INPUT TO BAS TO INITIATE
ADDITIONAL AHU SHUT DOWN SEQUENCE.
BAS CONNECTION TO FAN UNIT CONTROLLER.
5
B
5
FACP
TrueAlert 2-WIRE ADDRESSABLE CONTROL OF VISIBLE
AND AUDIBLE NOTIFICATION ACTIVATES APPLIANCES WITH:
HORNS SOUNDED AS TEMPORAL OR MARCH TIME PATTERN, OR ON
CONTINUOUSLY, CONTROLLED SEPARATELY FROM VISIBLE APPLIANCES
ON THE SAME TWO-WIRE CIRCUIT
TrueAlert NOTIFICATION APPLIANCE DESIGN PROVIDES
FLEXIBLE, EASY, AND CONVENIENT FLUSH OR SURFACE WALL BOX MOUNTING
FACP
SPECIFICATIONS:
5
STROBE:
RATED VOLTAGE RANGE: 23 TO 31 VRMS
SUPERVISORY REQUIREMENTS: 1 UNIT LOAD
STROBE FLASH RATE: 1 Hz
5
2
2
4
3
4
3
MODEL NUMBER
1
C
49VO-WRFO(-BA)
49VO-WWFO-BA
49VO-APPLW-O
1
PHYSICAL EDUCATION BUILDING
WELLNESS CENTER BUILDING
49VO-APPLW-CO
49VO-WRFO-C
HOUSING LETTERING
VOLTAGE
COLOR
COLOR
RED
WHITE
WHITE
RED
WP BACKBOX AND
COVER ORDERED
SEPARATELY
RED
2
POSITION 1: CONFIGURATION CONTROL - LOCAL (OFF), PANEL (ON)
POSITION 2: AUDIBLE VOLUME - HIGH (OFF), LOW (ON)
POSITION 3: CANADIAN HORN MODE - SET TO OFF
POSITION 4: LEGACY NAC MODE - SET TO OFF
POSITION 5,6,7: UNUSED - SET TO OFF
POSITION 8: CLEAR/COLOR LENS - ALARM (OFF), ALERT (ON)
WHITE
23 VRMS
23 VRMS
23 VRMS
VOLTAGE
23 VRMS
23 VRMS
UL 1971
0°-49° C
75cd
0.160
0.160
0.160
ULC RATINGS
20cd
30cd
0.143
0.150
0.143
0.150
15cd
0.060
0.060
0.060
HOUSING DIMENSIONS (INCLUDING LENS): 5 1/8" H X 5" W X 2 5/8" D
TEMPERATURE RANGE: -31° TO 120° F (-35° TO 49° C)
HUMIDITY RANGE: 10% TO 93% NON-CONDENSING AT 104° F (40° C)
CONNECTIONS: TERMINAL BLOCKS FOR 18 TO 12 AWG
NO SCALE
A
IMPORTANT!
WALL MOUNT INSTALLATION
HEIGHT REFERENCE
BOTTOM OF LENS
IS EITHER EVEN WITH
OR SLIGHTLY ABOVE
BOTTOM OF
COMPATABLE BOXES
ELECTRICAL
BOX OUTLINE
WEATHER PROOF BOX 1-5/8" DEEP
SIMPLEX 49WPBB-AVVOWR
SIMPLEX 4905-9899
CONDUIT CUTOUTS ARE PROVIDED
ON ALL FOUR SIDES.
NFPA 72 REQUIRES THAT
THE ENTIRE LENS BE NOT
LESS THAN 80" AND NOT
GREATER THAN 96" ABOVE
THE FINISHED FLOOR.
80"
MIN.
MAGNETIC TEST
LOCATION
LSB
RESERVED FOR
FUTURE USE
1 2 3 4 5 6 7 8
B
STROBE INTENSITY SETTING
SAN JOSE CITY
COLLEGE
MOUNTING INSTRUCTIONS:
DIP SWITCHES 5 & 6
0000
1000
0100
NOT
0=OFF
1=ON
DIP SWITCHES 1100
USED
0010
1 THRU 4
1010
UL 1638
UL 1638
0110
1110
TO 0° C
TO -35° C
0001
WP 75cd
WP 185cd
WP 75cd
WP 185cd
1001
0.239
0.160
0.212
0.185
0101
0.239
0.160
0.212
0.185
1101
0.239
0.160
0.212
0.185
0011
1011
75cd
0111
0.168
1111
0.168
0000
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
1000
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
0100
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
1. SET THE APPLIANCE ADDRESS AND CONFIGURATION SETTINGS.
2. BRING THE BUILDING WIRING THROUGH THE RECTANGULAR OPENING IN THE APPLIANCE.
1100
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
3. ASSEMBLE THE HOUSING ONTO THE WEATHERPROOF BACKBOX ASSURING
EVEN CONTACT WITH THE GASKET AROUND THE PERIPHERY.
PHYSICAL EDUCATION BUILDING AND
RENOVATED LAB BUILDING
4. USING THE MOUNTING HOLES INDICATED IN THE FIGURE ABOVE, ASSEMBLE THE
HOUSING TO THE BACKBOX. TIGHTEN THE SCREWS TO RECOMMENDED TORQUE
SAN JOSE, CALIFORNIA
5. ASSEMBLE THE COVER TO THE WEATHERPROOF BACKBOX USING THE
SCREWS PROVIDED. TIGHTEN THE SCREWS TO RECOMMENDED TORQUE.
49VO
CKT
+
49VO
2
1
FROM TrueAlert COMPATIBLE
SLC CONTROLLER (SEE NOTES)
CKT
49VO
C
2
1
-
(130 mm X 127 mm X 67 mm)
WIRING NOTES:
PCAF
51
57
57PW
581PW
SURFACE MOUNTING
TrueAlert V/O UNITS- DIP SWITCH ADDRESS CHART
MSB
INTENSITY SELECTION
PLUG, ACCESSIBLE
ONLY FROM REAR OF
HOUSING; FACTORY
SETTING IS FACP.
CONTROLLED BY PANEL.
ADDRESS SETTING
DIP SWITCH
GENERAL SPECIFICATIONS:
1 HVAC FAN SHUT DOWN DIAGRAM
1
DIP SWITCH
ACCESSABLE FROM REAR
APPLIANCE CONFIGURATION SETTINGS
LED INDICATOR AND MAGNETIC TEST FEATURE:
LED INDICTOR CAN BE ELECTED TO DISPLAY EACH POLLING CYCLE
TO INDICICATE APPLIANCE SUPERVISION
WHEN THE TrueAlert CONTROLLER IS IN DIAGNOSTIC MODE, THE
MAGNETIC TEST PULSES THE LED TO INDICATE APPLIANCE ADDRESS
AND IS SELECTABLE TO ALSO BRIEFLY FLASH THE STROBE TO
CONFIRM OPERATION
BAS CONNECTION TO FAN UNIT CONTROLLER.
3
TM
TrueAlert
ES (STYLE 4 SLC) VISIBLE ONLY NOTIFICATION APPLIANCES 49VO SERIES
WEATHERPROOF
CONFIGURATION
INDIVIDUALLY ADDRESSED WALL MOUNT VISIBLE
NOTIFICATION APPLIANCES WITH EFFICIENT ELECTRONIC
HIGH INTENSITY XENON STROBE PROVIDES:
SUPERVISION OF EACH INDIVIDUAL APPLIANCE'S WIRING AND
CONNECTIONS
ABILITY TO CONNECT USING "T" TAPPING FOR CLASS B/STYLE 4
CIRCUITS TO SIMPLIFY WIRING
HORNS CONTROLLED SEPARATELY FROM STROBES ON THE SAME
2-WIRE CIRCUIT ALLOWING "ON-UNTIL-SILENCED" AND
"ON-UNTIL RESET".
XENON STROBE OUTPUT IS MANUALLY SELECTABLE FOR 15, 30, 75,
110, 135 AND 185 CANDELA OR "FACP". THE "FACP" SETTING ALLOWS
THE 4100 TO PROGRAM THE CANDELA SETTING.
IN/OUT WIRING ACCESSIBILITY FROM FRONT OF HOUSING PROVIDES
EASY ACCESS FOR INSTALLATION, INSPECTION, AND TESTING
MAGNETIC TEST DIAGNOSTICS TO ASSIST CHECKOUT AND TESTING
OF APPLIANCES AND WIRING
UL LISTED TO STANDARD 1971
A
DETAIL 1 KEYNOTES
4
2
1
+
SLC -
SLC SLC +
SLC +
49VO
CKT
1
+
-
NO.
49VO
1
2
CKT
+
-
SLC -
SLC -
SLC +
SLC +
ISSUE
DATE
2
CKT
+
1. REFER TO FIELD WIRING DIAGRAMS OF THE DRIVING TrueAlert COMPATIBLE CONTROLLER FOR ADDITIONAL SLC WIRING INFORMATION.
2. NOTIFICATION APPLIANCES ARE RATED PER INDIVIDUAL NAMEPLATE LABEL.
3. MAINTAIN CORRECT POLARITY ON TERMINAL CONNECTIONS. DO NOT LOOP WIRES UNDER TERMINALS.
4. ALL TrueAlert SLC WIRING CONNECTIONS ARE SUPERVISED AND POWER-LIMITED.
5. POWERING THE V/O FROM AN APPLIANCE POWER SOURCE LESS THAN 17 VDC OR GREATER THAN 32 VDC MAY CAUSE PERMANENT DAMAGE.
TO THE V/O UNIT.
6. THE TrueAlert V/O CAN ONLY BE OPERATED THROUGH A 4009 TrueAlert ADDRESSABLE CONTROLLER OR TrueAlert COMPATIBLE FACP.
D
D
4603-9101 REMOTE ANNUNCIATOR
ET-1010/ET-1011 SPEAKER ASSEMBLY
PRODUCT INFORMATION
FEATURES:
UL LISTED
FM APPROVED
FLUSH MOUNT ON STANDARD ELECTRICAL BOXES
4.09
4.29
SPECIFICATIONS:
VOLTAGE: 24VDC NOMINAL
CURRENT: ALARM 140mA
SUPERVISORY 65mA
OPERATING TEMPERATURE: 32° F TO 120° F
HUMIDITY RANGE: 10% TO 90% RH FROM 32° F TO 104° F
STANDARD TRIM: BEIGE (SUPPLIED WITH BOTH SLOTTED AND
TAMPERPROOF SCREWS)
E
E
OPTIONS
4.29
BRUSHED ALUMINUM TRIM: 4603-9111
SURFACE BOX: 2975-9206
DIMENSIONS 11 31/32"L X 4 5/8" W X 2 3/4"D
FINISH: LIGHT BROWN ENAMEL
TO FLUSH-MOUNT IN MASONRY WALLS, USE A
A RAYCO 965 (3-1/2" DEEP) MASONRY BOX OR
ITS EQUIVALENT.
TO FLUSH-MOUNT IN PLASTERBOARD WALLS, USE A
STEEL CITY GW-635-G OR A RAYCO EQUIVALENT.
TO SURFACE-MOUNT, USE A SIMPLEX 2975-9206
BACK BOX
NOTES:
TO ADDITIONAL 24VDC POWERED DEVICES IF USED
FROM 24 VDC POWER SOURCE
4.29
+
TB1
-
+
-
-
TB2
-
+
TO NEXT SPEAKER
OR END OR LINE RESISTOR
(EOLR)
F
+
F
FROM PRECEDING SPEAKER
OR FIRE ALARM
CONTROL PANEL (FACP)
FLUSH MOUNTING
1. ALL WIRING TO BE No. 18 AWG OR TO LOCAL CODE.
2. ALL WIRING SUPERVISED
3. WIRE TO BE 18 AWG TWISTED SHIELDED PAIR RECOMMENDED
CONSULT SALES ENGINEERING FOR EXCEPTIONS.
2500 FT ONE WAY MAX COMMUNICATION LINE POWER
32 VDC MAX
130 mA MAX
1200 OR 9600 BAUD
4. WHEN WIRING LEAVES THE BUILDING, OVER VOLTAGE
PROTECTORS ARE REQUIRED; USE 2081-9044 ONE IS
INSTALLED WHERE IT LEAVE THE BUILDING AND ONE
WHERE IT ENTERS THE NEXT BUILDING. TWO 2081-9044
(MAX)
4.29
S
S
FROM PREVIOUS RUI DEVICE OR
FIRE ALARM CONTROL PANEL
OF F
COM
+
TO NEXT RUI DEVICE OR RETURN TO
FIRE ALARM CONTROL PANEL IN STYLE 6 SYSTEM
ON
G
G
FOR RUI ADDRESSABLE SETUP
SEE INSTALLATION INSTRUCTIONS
579-
ARCHITECT'S STAMP
APPROVAL
THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO LPAS, INC. AND IS FURNISHED FOR THE
PURPOSES OF REVIEW, BIDDING OR CONSTRUCTION OF THE PROJECT LISTED IN THE JOB TITLE BOX ABOVE
AND SHALL NOT BE USED FOR ANY OTHER PURPOSE OR RELEASED TO ANY OTHER PARTY WITHOUT THE
WRITTEN CONSENT OF LPAS, INC. INFOMATION CONTAINED HEREIN IS AN INSTRUMENT OF PROFESSIONAL
SERVICES AND SHALL REMAIN THE PROPERTY OF LPAS, INC. ALL RIGHTS RESERVED COPYRIGHT © 2009.
THIS DRAWING IS NOT FINAL OR TO BE USED FOR CONSTRUCTION UNTIL IT IS SIGNED BY THE ARCHITECT
AND ENGINEER.
H
H
CONSULTANT
2014-0174
Joe Ripp
J
ON LA
AS
AL
I NE ER
J
J
F E S S I ON
No. E16806
AT
EL
L
E CT RICA N
E O
OR
F CAL I F
IA
ST
717 Market Street
Suite 500
San Francisco, CA 94103
TEL
415.489.7240
FAX
415.489.7289
www.interfaceengineering.com
PRO
U
E N G I N E E R I N G
D
ENG
INTERFACE
RE
CONTACT
R EG I S T E
PROJECT
DETAILS - FIRE ALARM
PROJECT NO: 1089-0001
DATE: 1.12.2015
K
K
SHEET NO:
FA7.01
12
11
10
9
8
7
6
5
4
3
2
1
DSA SUBMITTAL
12
11
10
9
UL LISTED, FM APPROVED
TRUEALARM ANALOG SENSING PROVIDES DIGITAL TRANSMISSION OF ANALOG
SENSOR VALUES VIA MAPNETII, OR IDNet SLC TWO WIRE COMMUNICATIONS
FIRE ALARM CONTROL PANEL PROVIDES:
-INDIVIDUAL SENSITIVITY SELECTION FOR EACH SENSOR
-PEAK VALUE LOGGING ALLOWING ACCURATE ANALYSIS FOR SENSITIVITY SELECTION
-AUTOMATIC ENVIRONMENTAL COMPENSATION
-DISPLAY OF SENSITIVITY IN PERCENT PER FOOT
-MULTISTAGE ALARM OPERATION
-ABILITY TO DISPLAY AND PRINT DETAILED SENSOR INFORMATION IN PLAIN ENGLISH LANGUAGE
PHOTOELECTRIC SMOKE SENSOR 4098-9714:
SEVEN LEVELS OF SENSITIVITY FROM 0.2% TO 3.7%
IONIZATION SMOKE SENSOR 4098-9717:
FOUR LEVELS OF SENSITIVITY FROM 0.5% TO 1.7%.
HEAT SENSOR 4098-9733:
-RATE-OF-RISE TEMPERATURE DETECTION IS SELECTABLE AT THE CONTROL PANEL FOR EITHER 15°F
OR 20°F PER MINUTE
-FIXED TEMPERATURE SENSING IS INDEPENDENT OF RATE-OF-RISE AND PROGRAMMABLE TO OPERATE
AT 135°F OR 155°F
-TRUEALARM HEAT SENSORS CAN BE PROGRAMMED AS A UTILITY DEVICE TO MONITOR
FOR TEMPERATURE EXTREMES IN THE RANGE FROM 32° F TO 120° F.
UL STANDARD SPACING:
-60 FT SPACING FOR 135° F
-40 FT SPACING FOR 155° F
INTEGRAL RED LED FOR POWER-ON (PULSING), OR ALARM OR TROUBLE (STEADY ON)
BASE MOUNTED ADDRESS SELECTION:
-ACCESSIBLE FROM FRONT (DIP SWITCH UNDER SENSOR)
-ADDRESS REMAINS WITH ITS PROGRAMMED LOCATION
FOR USE WITH SIMPLEX 4010, 4100, 4020, AND 4120 SERIES CONTROL PANELS.
MAXIMUM QUANTITY OF DEVICES:
-127 FOR 4020, 4100, 4120
-250 FOR 4010, 4100
MOUNTING: CEILING OR WALL
COLOR : FROST WHITE
BASE DIMENSIONS: 15/16" X 4-7/8"
B
7
4098-9792 STANDARD SENSOR BASE
PRODUCT INFORMATION
FEATURES:
A
8
4" X 1 1/2" DEEP OCTAGONAL
OR
4" SQUARE X 1 1/2" DEEP, WHICH REQUIRES
A 4098-9832 ADAPTER PLATE (6-3/8" X 1/4")
BOX SUPPLIED BY CONTRACTOR
MAPNETII/IDNet ADDRESS DIP SWITCHES
SEE BASE INSTALLATION INSTRUCTIONS
574-709 FOR SETTINGS
4098-9714 PHOTOELECTRIC SMOKE SENSOR
4098-9717 IONIZATION SMOKE SENSOR
(BOX TO BE FLUSH OR RECESSED 1/4" MAXIMUM)
+
+
TO ADDITIONAL MAPNETII/IDNet DEVICES
OR RETURN TO FIRE ALARM CONTROL
PANEL FOR A STYLE 6 APPLICATION
OPTIONAL SHIELD
-
-
4090-9002 IDNet SLC, INDIVIDUAL ADDRESSABLE OUTPUT MODULE RELAY (AOM)
RELAY IAM
BACK BOX COVER OPTIONS;
SEMI-FLUSH TRIM PLATE 4090-9801 (SHOWN)
WITH LIGHT PIPE FOR LED VIEWING
SURFACE TRIM PLATE 4090-9802
WITH LIGHT PIPE FOR LED VIEWING
2-GANG BACK BOX COVER
SUPPLIED BY CONTRACTOR
MODEL
4098-9756
MODEL
2098-9808
2098-9806
NOT USED
ADDRESS SETTING UNDER
RE-SEALABLE LABEL
S
R
+
R
-
2
3
11
B
+
FROM PREVIOUS SLC DEVICE
3
OR F.A.C.P.
-
IDNet SLC
TO F.A.C.P.
3
4
4
4
NO.
733-984
(1.8K 1/2W)
3
ISSUE
DATE
3
733-886
(6.8K 1/2W)
733-896
(4.7K 1/2W)
WIRING FOR CURRENT LIMITED OPERATION
3
D
EXHAUST TUBE
CUT TO 1/2 OF
DUCT WHEN < 24"
DO NOT INSERT
RUBBER PLUG
TEST
E
R
R
2098-9808
REMOTE STATUS/ALARM
INDICATOR
FOR DUCT WIDTHS
3' TO 95"
2098-9806
TEST STATION
FOR DUCT WIDTHS
8" TO 3'
(OPTIONAL)
(OPTIONAL)
4098-9756
4-WIRE DUCT SENSOR
2098-9808
ALARM INDICATOR
2098-9806 REMOTE ALARM INDICATOR/KEY SWITCH
SW2 1
2
3
4
5
6
7
8
RED
ALARM
LED
SEE NOTES
3, 4
4098-9756
4-WIRE DUCT SENSOR
2098-9806
REMOTE ALARM
INDICATOR/
KEYSWITCH
RED
ALARM
LED
SW2 1
2
3
4
5
6
7
8
ADDRESS
SWITCH
TB1 1
+
2
-
LED
3
ADDRESS
SWITCH
4
5
6
7
8
TEST
9 10 11 12 13 14 15 16
TEST MAP + MAP -
+24V
+
24C
-
TB1 1
+
SEE NOTES 3,4
ALM
2
3
-
TEST MAP + MAP -
LED
4
5
6
7
8
9 10 11 12 13 14 15 16
+24V
BLK
UL LISTED
CONTROL PANEL
SIMPLEX 4010, 4020
4008, 4100+ OR 4120
F
TO OTHER MAPNETII/
IDNET SLC DEVICES
SEE NOTE 2 OR
RETURN TO FACP
FOR STYLE 6 SLC
+
+
-
SHIELD
(OPTIONAL)
POWER CIRCUIT
24 VDC
-
ALM
RED
BLK
RED
MAPNET II/IDNet
+
24C
WHT
SHIELD
WHT
-
SEE NOTE 1
5
+
BLU
YEL
4098-9843
PAM-SD
RELAY
-
RED
1. DUCT SENSOR WIRING IS 12 TO 18 AWG.
2. MAXIMUM QUANTITY OF DEVICES PER CIRCUIT IS 127 FOR 4020,
4100+, OR 4120, AND 250 FOR THE 4010 PANEL
3. THE 2098-9806 AND 2098-9808 ARE POLARIZED, OBSERVE COLOR-CODED WIRING.
4. MAXIMUM WIRE LENGTH TO TEST TERMINALS AND REMOTE LED IS 250 FEET.
5 4098-9843 PAM-SD RELAY (AIR PRODUCTS & CONTROL LIMITED) ARE RATED AT
7 AMPS 28 VDC/10 AMPS @ 115 VAC. MAXIMUM WIRE LENGTH TO PAM-SD RELAYS IS
500 FT. (15 PAM-SD RELAYS MAX.). WIRING FROM THE RELAY TO THE
DEVICE IT IS CONTROLLING SHOULD BE NO MORE THAN 3 FT. (PER NFPA 72).
SHIELD
1/2 W 10K EOL
RESISTOR
4081-9008
ORG N.O.
+
WIRING NOTES:
C
N.C.
RED
WHT
1/2 W 10K EOL
RESISTOR
4081-9008
C
N.C.
BLU
YEL
N.O. ORG
4098-9843
PAM-SD
RELAY
5
+
RED
FIRE
SMOKE
DAMPER
WHT
-
RED
AIR
HANDLING
UNIT
FSD POWER
(BY OTHERS)
AHU POWER
(BY OTHERS)
G
AIR PRODUCTS PAM-SD 24VDC POLARIZED RELAY MODULE
(SIMPLEX 4098-9843)
SPECIFICATIONS:
FEATURES:
UL LISTED
CALIFORNIA STATE FIRE MARSHAL LISTING NUMBERS:
2908-9806 ALARM INDICATOR 7300-0026:150
MOUNTING: FLUSH
FINISH: CHROME OR STAINLESS STEEL
4
3
NORMAL
MAPNETII OR IDNET SLC COMMUNICATION, AUTO-SELECT
1 ADDRESS PER HOUSING, PROVIDES OPERATING POWER
TO MODEL 4098-9755
MODEL 4098-9756 WITH SUPERVISED MULTIPLE RELAY CONTROL, REQUIRES SEPARATE FUSED
24 VDC FROM FIRE ALARM POWER SUPPLY
INPUT VOLTAGE
17-32 VDC (24 VDC NOMINAL)
STANDBY CURRENT
3 mA @ 24 VDC
15 mA @ 24 VDC, ADD 15 mA ADDITIONAL FOR EACH
ALARM CURRENT
4098-9843 RELAY
4098-9843 RELAY OUTPUT RATINGS, SINGLE FORM C
15 mA @ 24 VDC UP TO 15 MAX. PER RELAY CONTROL
COIL CURRENT
OUTPUT
RELAY CONTACTS, RESISTIVE RATINGS
7 A @ 28 VDC & 120 VAC; 250 uA @ 5 VDC
500 FT. (152m) MAX. TO RELAY COILS, RELAY MUST BE
LOCATION DISTANCE
WITHIN 3 FT. (1m) OF DEVICE BEING CONTROLLED PER
NFPA 72, SECTION 3-9.2.1
S
B
2
SECONDARY IDNet/MAPNET SLC LINES
5 8 9 10
C
R
ADDRESSABLE OPERATION
SECONDARY IDNet SLC LINES
1
2
R
DATA COMMUNICATIONS
7
I
ON
574-184 REV A
OPTIONAL SHIELD
2
ALARM
300 TO 4000 FT/min (91 TO 1220 m/min)
0.2% TO 3.7% PER FOOT OF OBSCURATION, SELECTABLE
AT HOST CONTROL PANEL
32° F TO 100° F (0° C TO 38° C)
UL LISTED TEMPERATURE RANGE
32° F TO 122° F (0° C TO 50° C)
OPERATING TEMPERATURE RANGE
0° F TO 140° F (-18° C TO 60° C)
STORAGE TEMPERATURE RANGE
10% TO 95% RH, NON-CONDENSING
HUMIDITY RANGE
BLACK BASE WITH CLEAR COVER
HOUSING COLOR
WIRING CONNECTIONS
TERMINAL BLOCKS, 18 TO 12 AWG
REMOTE STATUS/ALARM LED AND TEST STATION WITH REMOTE STATUS/ALARM LED
1.2 mA, NO IMPACT TO ALARM CURRENT (2098-9808
REMOTE ALARM LED CURRENT
OR 2098-9806)
TEST STATION KEYSWITCH CURRENT
3.3 mA, NO IMPACT TO ALARM CURRENT (2098-9806)
REMOTE ALARM LED AND TEST
250
FT. (76m) MAXIMUM
STATION DISTANCE
NORMALLY OPEN (N.O.)
4090-9002
RELAY IAM
NOT USED
PRIMARY
IDNet SLC LINES
1 2 11
I
SAN JOSE, CALIFORNIA
ALARM
SENSOR SENSITIVITY RANGE
COMMON
COMMON
NORMALLY OPEN (N.O.)
B B
TUBE SUPPORT HOLE SHALL BE USED
FOR DUCTS MORE THAN 3 FEET WIDE
INSERT RUBBER PLUG
GENERAL SPECIFICATIONS
AIR VELOCITY RANGE (LINEAR FT/MIN)
4
5
8
9
NORMALLY CLOSED (N.C.)
574-184 REV A
RR
ON
4
5
8
9
NORMALLY CLOSED (N.C.)
4090-9002
RELAY IAM
B B
DUCT SMOKE SENSOR HOUSING WITH PHOTOELECTRIC SENSOR
COMPATIBILITY
DESCRIPTION
DUCT HOUSING WITH SUPERVISED MULTIPLE RELAY CONTROL FOR UP
SIMPLEX
FIRE
ALARM CONTROL MODELS
TO 15, 4098-9843 RELAYS (ORDERED SEPARATELY), REQUIRES
4008, 4010, 4020, 4100, AND 4120.
SEPARATE 24 VDC FIRE ALARM POWER AND RELAY END-OF-LINE
RESISTOR
REMOTE LED INDICATOR AND TEST STATION, SELECT ONE IF REQUIRED
MOUNTING
DESCRIPTION
USE SINGLE GANG BOX,
RED LED STATUS INDICATOR
3" H X 2" W X 2" D
TEST STATION WITH KEYSWITCH AND RED LED STATUS (TURNING
(76 mm X 51 mm X 51 mm)
SWITCH TO TEST INITIATES ALARM FOR SYSTEM TESTING
SPECIFICATIONS:
WIRING NOTES:
RR
SHIELD
+ IDNet/MAPNET
- IDNet/MAPNET
DUCT DETECTOR SELECTION CHART
DUCT SENSOR HOUSING WITH SUPERVISED OUTPUT FOR
MULTIPLE REMOTE RELAYS, REQUIRES SEPARATE 24 VDC
(RELAYS ARE UNDER PANEL CONTROL AND CAN BE
ACTIVATED MANUALLY OR BY A SEPARATE ALARM/INPUT)
GENERAL FEATURES:
UL LISTED TO STANDARD 268A
CLEAR COVER ALLOWS VISUAL INSPECTION
TEST PORTS PROVIDE FUNCTIONAL SMOKE TESTING ACCESS
WITH COVER IN PLACE
MOUNTS TO RECTANGULAR DUCTS OR ROUND DUCTS
(MINIMUM SIZE 8" SQUARE OR 18" DIAMETER)
MAGNETIC TEST FEATURE FOR ALARM INITIATION AT HOUSING
OPTIONAL WEATHERPROOF ENCLOSURE IS AVAILABLE
SEPARATELY (REFER TO DATA SHEET S4098-0032)
DIAGNOSTIC LEDS (ON INTERFACE BOARD):
RED ALARM/TROUBLE LED FOR SENSOR STATUS AND
COMMUNICATIONS POLLING DISPLAY
YELLOW LED FOR OPEN OR SHORTED TROUBLE INDICATION
OF SUPERVISED RELAY CONTROL
SAMPLING TUBES (ORDERED SEPARATELY):
AVAILABLE IN MULTIPLE LENGTHS TO MATCH DUCT SIZE
INSTALLED AND SERVICED WITH HOUSING IN PLACE
REMOTE MODULE OPTIONS (ORDERED SEPARATELY):
RED STATUS/ALARM LED (2098-9808)
TEST STATION WITH LED (2098-9806)
RELAYS USED (4098-9843)
4" SQUARE X 2 1/8" DEEP BOX
SUPPLIED BY CONTRACTOR
IDNet SLC RELAY MODULES ALLOW THE SIMPLEX FIRE ALARM
CONTROL PANEL TO CONTROL A REMOTELY LOCATED FORM
"C" CONTACT USING IDNet ADDRESSABLE COMMUNICATIONS
FOR BOTH DATA AND POWER. TYPICAL APPLICATIONS
WOULD BE FOR SWITCHING LOCAL POWER FOR CONTROL
FUNCTIONS SUCH AS ELEVATOR CAPTURE, OR CONTROL OF
HVAC COMPONENTS, PRESSURIZATION FANS, DAMPERS, ETC.
RELAY STATUS IS ALSO COMMUNICATED REQUIRING ONLY ONE
DEVICE ADDRESS.
1
PRIMARY IDNet/MAPNET SLC LINES
8 9 10
S
R
B
SAN JOSE CITY
COLLEGE
PHYSICAL EDUCATION BUILDING AND
RENOVATED LAB BUILDING
TO ADDITIONAL
DEVICES OR RETURN
TO FIRE ALARM
CONTROL PANEL FOR
STYLE 6 SYSTEM
APPLICATION
6
OPTIONAL SHIELD
S
R
B
SUPERVISED INPUT:
- 4090-9001 AIM WITH T-SENSE CAPABILITY HAS A
SUPERVISED INPUT THAT MONITORS FOR CONTINUITY
TO AN END-OF-LINE RESISTOR AND CAN DIFFERENTIATE
BETWEEN A SHORT CIRCUIT CONTACT CLOSURE AND A
CURRENT LIMITED CONTACT CLOSURE.
FOUR STATE OPERATION:
- NORMAL IS WHEN ALL CONTACTS ARE OPEN AND THERE
IS CONTINUITY TO THE END-OF-LINE RESISTOR.
- OPEN IS WHEN CONTINUITY DOES NOT EXIST TO THE END-OF-LINE
RESISTOR, CAUSING A TROUBLE CONDITION.
- SHORT, INDICATES THAT A CONTACT HAS CLOSED THAT IS
DIRECTLY CONNECTED TO THE INPUT CIRCUIT.
- CURRENT LIMITED INDICATES THAT A CONTACT HAS
CLOSED BEYOND A SERIES CONNECTED CURRENT
LIMITING RESISTOR. THIS OPERATION ALLOWS
DIFFERENTIATION BETWEEN TWO DIFFERENT CONTACT
TYPES DUE TO THEIR WIRING LOCATION, AND REPORTING
AS A SINGLE IDNET ADDRESSABLE POINT TO A
4100U FIRE ALARM CONTROL PANEL.
MODEL:
SPECIFICATIONS:
PRODUCT INFORMATION
B
4098-9756 ADDRESSABLE ANALOG 4-WIRE DUCT SENSOR MAPNET II/IDNet SLC WITH 24VDC RELAY
COMPACT AIR DUCT SENSOR HOUSING WITH CLEAR COVER
TO MONITOR FOR THE PRESENCE OF SMOKE
INCLUDES FACTORY INSTALL TRUEALARM PHOTOELECTRIC SMOKE
DETECTOR AND FEATURES:
INDIVIDUAL SENSOR INFORMATION PROCESSED BY THE HOST
CONTROL PANEL T0 DETERMINE SENSOR STATUS
DIGITAL TRANSMISSION OF ANALOG SENSOR VALUES VIA
MAPNET II OR IDNET SLC 2-WIRE COMMUNICATIONS
PROGRAMMABLE SENSITIVITY, CONSISTENT ACCURACY,
ENVIRONMENTAL COMPENSATION, STATUS TESTING, AND
MONITORING OF SENSOR DIRT ACCUMULATION
DESCRIPTION:
SHIELD
IDNet/MAPNET +
IDNet/MAPNET -
T-SENSING OPERATION:
PRODUCT INFORMATION
FEATURES:
RELAY IAM POWER: SUPPLIED BY IDNet COMMUNICATIONS
RELAY IAM CONTACTS (FORM "C", SPDT)
POWER LIMITED RATING: 2A @ 24VDC, TRANSIENT SUPPRESSED
LOADS, 1A @ 24VDC FOR INDUCTIVE LOADS
NON POWER LIMITED RATING: 1/2A @ 24VAC, TRANSIENT SUPPRESSED
LOADS, 1A @ 24 VDC FOR INDUCTIVE LOADS
WIRE CONNECTIONS: SCREW TERMINALS FOR IN/OUT
WIRING, #18 TO #14 AWG WIRE
COMPATIBLE WITH SIMPLEX 2081-9044 OVER VOLTAGE PROTECTORS
DIMENSIONS: 4 1/8"H x 4 1/8"W x 1 3/8"D (105mm x 105mm x 35mm)
HOUSING MATERIAL: BLACK THERMOPLASTIC
MOUNTING PLATE MATERIAL: SHEET METAL, GALVANIZED
TEMPERATURE RANGE: 32° F TO 120° F (0° C TO 49° C)
INTENDED FOR INDOOR OPERATION
HUMIDITY RANGE UP TO 93% RH AT 100° F (38° C)
6
FROM UL-LISTED
F.A.C.P. OR
PREVIOUS
SLC DEVICE
1. ALL WIRING TO COMPLY WITH LOCAL CODE.
2. CONDUCTORS MUST TEST FREE OF ALL GROUNDS.
3. ONLY N.O. DRY CONTACTS ARE ALLOWED.
4. MAXIMUM WIRE LENGTH (NO. 18 AWG) IS 400 FT. W/2081-9044
OVER VOLTAGE PROTECTORS OR 400 FT. W/O PROTECTORS.
5. A MAXIMUM QUANTITY OF DEVICES PER CIRCUIT: CONTROL PANEL
MODULE DEPENDENT
6. IF SHIELD IS PRESENT, CONNECT TO THE OUTGOING IDNet SHIELD
TO PROVIDE A CONTINUOUS SHIELD OVER THE LENGTH OF THE
IDNet CHANNEL. METHOD OF SPLICE DETERMINED BY AHJ.
7. REFER TO INSTALLATION INSTRUCTIONS 574-331.
8. MAXIMUM ALLOWABLE LINE RUN FROM THE F.A.C.P. TO THE
FARTHEST DEVICE, NOT TO EXCEED 2500 FEET.
9. MAXIMUM TOTAL WIRE (INCLUDING ALL T-TAPS) FROM THE
FIRE ALARM CONTROL PANEL
10. FOR STYLE 6 CIRCUIT WIRING IT IS RECOMMENDED
THAT THE PRIMARY 1 AND THE BACK-UP 2 LINES
BE IN SEPARATE WIRE RUNS AND IN COMPLIANCE
WITH LOCAL REQUIREMENTS.
11. REFER TO FIELD WIRING DIAGRAM 842-073
UL LISTED
A SINGLE ADDRESSABLE POINT BOTH CONTROLS A 2A FORM
"C" CONTACT AND TRACKS ITS STATUS
COMPATIBLE WITH SIMPLEX MODEL 4010 AND 4100 ADDRESSABLE
FIRE ALARM CONTROL PANEL
LATCHING RELAY DESIGN ALLOWS DATA AND POWER TO BE
BOTH SUPPLIED BY IDNet COMMUNICATIONS
COMPACT, SEALED CONSTRUCTION:
- SCREW TERMINALS FOR WIRING CONNECTIONS
- REDUCES DUST INFILTRATION
G
ADDRESS DIP SWITCHES UNDER
RE-SEALABLE LABEL
SEE INSTALLATION INSTRUCTIONS
(574-331) FOR SETTINGS
WIRING NOTES:
FEATURES:
F
BACK BOX COVER OPTIONS;
SEMI-FLUSH TRIM PLATE 4090-9806 (SHOWN)
WITH LIGHT PIPE FOR LED VIEWING
SURFACE TRIM PLATE 4090-9807
WITH LIGHT PIPE FOR LED VIEWING
SINGLE GANG COVER W/ 2 6/32
FLATHEAD SCREWS
(SUPPLIED BY CONTRACTOR)
THE 4090-9001 IS AN ADDRESSABLE INPUT MODULE (AIM)
WITH POWER AND COMMUNICATIONS SUPPLIED BY A TWO WIRE ADDRESSABLE
CIRCUIT. IT PROVIDES LOCATION SPECIFIC ADDRESSABILITY
TO A SINGLE INITIATING DEVICE (SUCH AS SINGLE STATION SMOKE
DETECTOR ALARM CONTACTS OR HEAT DETECTOR CONTACTS) OR
MULTIPLE DEVICES AT THE SAME LOCATION BY MONITORING
NORMALLY OPEN, DRY CONTACTS AND THE WIRING TO AN END-OF-LINE RESISTOR.
CLOSURE OF THE MONITORED CONTACTS INITIATES AN ALARM OR
OTHER RESPONSE AS PROGRAMMED AT THE FIRE ALARM
CONTROL PANEL. AN OPEN IN THE MONITORED CIRCUIT WIRING
WILL CAUSE A TROUBLE TO BE REPORTED.
IF THE INITIATING DEVICE CONTACTS ARE MOMENTARY, SUCH AS
FROM A RATE-OF-RISE HEAT DETECTOR, ENABLING THE LATCH
FEATURE WILL MAINTAIN THE ALARM CONDITION UNTIL THE SYSTEM
IS RESET. FOR APPLICATIONS WHERE THE CONTACT CLOSURE LATCHES,
OR IF ITS CONDITION NEEDS TO BE TRACKED AT THE CONTROL PANEL
NON-LATCHING OPERATION MAY BE ENABLED.
FROM PREVIOUS
MAPNETII/IDNet DEVICE
OR FIRE ALARM
CONTROL PANEL
1. IDNet LINES ARE TO BE #18 AWG TWISTED PAIR (CONSULT
SG SALES ENGINEERING FOR EXCEPTIONS).
2. MAXIMUM ALLOWABLE LINE RUN, FROM THE F.A.C.P. TO THE FARTHEST
DEVICE, NOT TO EXCEED 2500 FEET.
3. MAXIMUM QUANTITY OF DEVICES PER CIRCUIT: CONTROL PANEL
MODULE DEPENDENT
4. CONTRACTOR WIRING TO RELAY CONTACTS IS UNSUPERVISED.
USE #14 AWG WIRE TO LOCAL CODE.
5. RELAY CONTACTS RATED 2A, 24VDC (1A FOR INDUCTIVE LOAD)
RELAY CONTACTS RATED 0.5A 120VAC (NON POWER LIMITED)
FOR POWER-LIMITED OPERATION, POWER MUST BE PROVIDED
FROM FACP OR POWER-LIMITED POWER SUPPLY LISTED FOR FIRE
PROTECTIVE SIGNALING USE.
6. SEE INSTALLATION INSTRUCTIONS 574-184.
7. IF SHIELD IS PRESENT, CONNECT TO THE OUTGOING IDNet SHIELD
TO PROVIDE A CONTINUOUS SHIELD OVER THE LENGTH OF THE
IDNet CHANNEL. METHOD OF SPLICE DETERMINED BY AHJ.
8. WHEN CONNECTED TO A NON POWER-LIMITED SOURCE, THE WIRING
MUST MAINTAIN A MINIMUM 1/4 INCH SEPARATION FROM IDNet WIRING.
9. WHEN USED WITH NON POWER-LIMITED SOURCE, THE "POWER LIMITED
WIRING" INDICATION ON THE DEVICE LABEL MUST BE OBLITERATED.
10. WHEN BOTH POWER-LIMITED AND NON POWER-LIMITED SOURCES
ARE PRESENT, USE TYPE FPL, FPLR OR FPLP POWER LIMITED
CABLE FOR POWER-LIMITED CIRCUITS.
11. MAXIMUM TOTAL WIRE (INCLUDING ALL T-TAPS) ON CIRCUIT, FROM THE
F.A.C.P. NOT TO EXCEED 10,000 FEET OR .58uF. (CLASS B ONLY)
12. REFER TO FIELD WIRING DIAGRAM 842-073
4090-9810 BRACKET
REQUIRED WHEN USING
THE SIMPLEX TRIM PLATES
OPTIONAL WHEN USING
A CONTRACTOR SUPPLIED
SINGLE GANG COVER
DESCRIPTION:
TRUEALARM SENSOR BASES CONTAIN INTEGRAL ADDRESSABLE ELECTRONICS
THAT CONSTANTLY MONITOR THE STATUS OF THE DETACHABLE PHOTOELECTRIC,
IONIZATION, OR HEAT SENSORS. EACH SENSOR'S OUTPUT IS DIGITIZED AND
TRANSMITTED TO THE SYSTEM FIRE ALARM CONTROL PANEL EVERY FOUR SECONDS.
SINCE TRUEALARM SENSORS USE THE SAME BASE, DIFFERENT SENSOR TYPES
CAN BE EASILY INTERCHANGED TO MEET SPECIFIC LOCATION REQUIREMENTS. THIS
FEATURE ALLOWS INTENTIONAL SENSOR SUBSTITUTION DURING BUILDING CONSTRUCTION.
WHEN CONDITIONS ARE TEMPORARILY DUSTY, INSTEAD OF COVERING THE SMOKE SENSORS.
HEAT SENSORS MAY BE INSTALLED WITHOUT REPROGRAMMING THE CONTROL PANEL,
ALTHOUGH THE CONTROL PANEL WILL INDICATE AN INCORRECT SENSOR TYPE, THE HEAT
SENSOR WILL OPERATE AS A DEFAULT SENSITIVITY PROVIDING HEAT DETECTION FOR
BUILDING PROTECTION AT THAT LOCATION.
E
1
A
SUPERVISION RESISTOR: 6.8k 1/2W, (SUPPLIED)
SIMPLEX PART NO. 733-886
RESISTOR FOR CURRENT LIMITED OPERATION: 4.7k 1/2W,
WITH A 1.8k 1/2W
INPUT REQUIREMENTS: NORMALLY OPEN, DRY CONTACTS
HOUSING MATERIAL: BLACK THERMOPLASTIC
FLUSH MOUNTING
WIRING:
D
2
UL LISTED SINGLE
GANG ELECTRICAL BOX (2 1/8" MIN. DEPTH)
(SUPPLIED BY CONTRACTOR)
WIRE CONNECTIONS: SCREW TERMINALS FOR IN/OUT WIRING
FOR WIRE FROM #18 TO #14 AWG.
DIMENSIONS: 1 9/16" X 1 3/4" X 1 1/4"
TEMPERATURE RANGE: 32° F TO 158° F (0° C TO 70° C)
HUMIDITY: UP TO 93% RH AT 100° F
4098-9733 HEAT SENSOR
3
4090-9001 IDNET SLC, SUPERVISED ADDRESSABLE INPUT MODULE (AIM)
SPECIFICATIONS:
DESCRIPTION:
PRODUCT INFORMATION
4
UL LISTED
ADDRESSABLE COMMUNICATIONS SUPPLY BOTH DATA
AND POWER TO PROVIDE:
- SUPERVISED STYLE B MONITORING OF NORMALLY OPEN DRY CONTACTS.
- COMMUNICATIONS WIRING USING ONE TWISTED, SHIELDED WIRE PAIR.
COMPATIBLE WITH SIMPLEX ADDRESSABLE FIRE ALARM CONTROL PANELS.
COMPACT, SEALED CONSTRUCTION:
- ALLOWS MOUNTING IN A SINGLE GANG BOX
- REDUCES DUST INFILTRATION
PROVIDES CURRENT LIMITED MONITORING
- TO MONITOR TAMPER SWITCH (SUPERVISORY) AND
WATER FLOW SWITCH (ALARM) ON SAME CIRCUIT
- REQUIRES ONLY ONE ADDRESSABLE POINT
SELECTABLE LATCHING OPERATION
- MONITORS MOMENTARY CONTACT CLOSURES SUCH AS
RATE-OF RISE HEAT DETECTORS
UL LISTED TEMPERATURE RANGE: 32°F TO 100°F
OPERATING TEMPERATURE RANGE: 32°F TO 120°F
HUMIDITY RANGE: 10% TO 95% RH
PHOTOELECTRIC SENSOR AIR VELOCITY RANGE: 0-2000 FT/MIN
IONIZATION SENSOR AIR VELOCITY RANGE: 0-300 FT/MIN
WIRING CONNECTIONS: SCREW TERMINALS FOR IN/OUT WIRING, #18 TO #14 AWG
COMMUNICATIONS MAPNETII/IDNet SLC: 1 ADDRESS PER BASE
VOLTAGE (MAPNETII/IDNet SLC): 24-40VDC
CURRENT: 400uA TYPICAL
1. ALL WIRING TO COMPLY WITH LOCAL CODE.
2. CONDUCTORS MUST TEST FREE OF ALL GROUNDS.
3. MAINTAIN CORRECT POLARITY
4. MAPNETII/IDNet SLC WIRING TO BE #18 AWG TWISTED SHIELDED PAIR
5. IF SHIELD IS PRESENT, CONNECT TO THE OUTGOING IDNet SLC SHIELD
TO PROVIDE A CONTINUOUS SHIELD OVER THE LENGTH OF THE
IDNet SLC CHANNEL. METHOD OF SPLICE DETERMINED BY AHJ.
6. REFER TO INSTALLATION INSTRUCTIONS (574-707)
7. REFER TO APPLICATION MANUAL (574-709)
5
PRODUCT INFORMATION
FEATURES:
SPECIFICATIONS:
C
6
ARCHITECT'S STAMP
APPROVAL
POWER REQUIREMENTS: 0.015 AMP @ 24VDC
(17 VDC TO 32 VDC)
STANDARD SINGLE
GANG BOX 2" X 3"
MINIMUM DEPTH 2"
SUPPLIED BY CONTRACTOR
ANY SINGLE GANG BOX
SUPPLIED BY CONTRACTOR
RELAY: U.L. RECOGNIZED SPDT
THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO LPAS, INC. AND IS FURNISHED FOR THE
PURPOSES OF REVIEW, BIDDING OR CONSTRUCTION OF THE PROJECT LISTED IN THE JOB TITLE BOX ABOVE
AND SHALL NOT BE USED FOR ANY OTHER PURPOSE OR RELEASED TO ANY OTHER PARTY WITHOUT THE
WRITTEN CONSENT OF LPAS, INC. INFOMATION CONTAINED HEREIN IS AN INSTRUMENT OF PROFESSIONAL
SERVICES AND SHALL REMAIN THE PROPERTY OF LPAS, INC. ALL RIGHTS RESERVED COPYRIGHT © 2009.
CONTACT RATING: 7 AMPS @ 120VAC & 28 VDC
250 MICRO AMPS @ 5 VDC
AMBIENT TEMPERATURE: -50° F TO 85 °F (-50°C TO 85°C)
SPECIFICATIONS:
THIS DRAWING IS NOT FINAL OR TO BE USED FOR CONSTRUCTION UNTIL IT IS SIGNED BY THE ARCHITECT
AND ENGINEER.
APPROVALS: UNDERWRITERS LABORATORIES LISTED
ALARM CURRENT: 2.8 mA
DIMENSIONS OF BOX: 2 "W X 3"H X 2"D
COVER PLATE
SUPPLIED BY CONTRACTOR
12" 18 AWG WIRE LEADS
DIMENSIONS: 1-1/2"H X 1 7/8" W X 13/16" D
(38.1mm H X 47.625mm W X 20.638mm D)
DESCRIPTION:
H
FEATURES:
2098-9806 REMOTE TEST STATION, PROVIDES A REMOTE RED ALARM LED
STATUS INDICATOR AND A REMOTE TEST KEY ACTIVATED SWITCH
MOUNTED ON A SINGLE GANG STAINLESS STEEL PLATE. THE LED WILL
PULSE TO INDICATE NORMAL OPERATION OF THE DUCT DETECTOR AND
WILL ENERGIZE CONTINUOUS WHEN IN ALARM OR IN TROUBLE. (THE
EXACT STATUS OF THE SENSOR WILL BE DISPLAYED AT THE FIRE ALARM
CONTROL PANEL.) TURNING THE TEST SWITCH TO "TEST" WILL INITIATE AN
ALARM AND ALLOW THE RESULTING SYSTEM RESPONSES TO BE VERIFIED.
CONSULTANT
SINGLE SPDT RELAY
DOUBLE-SIDED ADHESIVE TAPE
2014-0174
Joe Ripp
10.0 AMP
CONTACTS
2098-9806
YEL ORG
BLU
J
C
N/C
J
N/O
ON LA
AS
AL
I NE ER
No. E16806
AT
EL
E CT RICA N
E O
OR
F CAL I F
L
717 Market Street
Suite 500
San Francisco, CA 94103
TEL
415.489.7240
FAX
415.489.7289
www.interfaceengineering.com
FLUSH MOUNTING
ST
MINIMUM 18 AWG OR TO LOCAL CODE.
CONDUCTORS MUST TEST FREE OF ALL GROUNDS.
REMOTE ALARM LED IS POLARIZED, OBSERVE
COLOR CODED WIRING.
ONE INDICATOR MAY BE INSTALLED PER DETECTOR.
F E S S I ON
U
E N G I N E E R I N G
WIRING:
PRO
ENG
INTERFACE
D
IA
5 WIRE NUTS
CONTACT
J
PROJECT
RE
MOUNTING SCREW
R EG I S T E
H
DETAILS - FIRE ALARM
RED (+)
CONNECT TO REMOTE
ALARM LED OUTPUT OF
APPROPRIATE
INITIATING DEVICES
BLACK (-)
PROJECT NO: 1089-0001
CONNECT TO REMOTE
TEST SWITCH INPUT ON
APPROPRIATE
INITIATING DEVICES
(-)
WHT
RED
WHT
K
DATE: 1.12.2015
(+)
RED
24VDC @ 0.015A
(18 VDC TO 32 VDC)
BACK VIEW
K
SHEET NO:
FA7.02
12
11
10
9
8
7
6
5
4
3
2
1
DSA SUBMITTAL
9
8
7
6
5
TM
4906 S/V
END-OF-LINE
RESISTOR (VALUE
DEPENDANT ON
FACP)
4906 S/V
SPKR +
SPKR +
SPKR +
SPKR -
SPKR -
SPKR -
JUMPER
POSITION
J1 TO TAP A
J1 TO TAP B
J1 TO TAP C
J1 TO TAP D
J1 TO TAP D
J1 TO TAP E
J1 TO TAP F
J1 TO TAP G
WATTAGE
VOLTAGE
SETTING
1/4
1/2
70.7VRMS
1
2
1/4
1/2
25VRMS
1
2
SLC -
STROBE +
STROBE +
STROBE +
STROBE -
STROBE -
STROBE -
SLC -
WIRING NOTES:
1. REFER TO FIELD WIRING DIAGRAMS OF THE DRIVING TrueAlert COMPATIBLE CONTROLLER FOR ADDITIONAL SLC WIRING INFORMATION.
REFER TO THE FIELD WIRING DIAGRAMS SUPPLIED WITH THE 4100/4003 FOR ADDITIONAL NAC WIRING INFORMATION.
2. NOTIFICATION APPLIANCES ARE RATED PER INDIVIDUAL NAMEPLATE LABEL.
3. MAINTAIN CORRECT POLARITY ON TERMINAL CONNECTIONS. DO NOT LOOP WIRES UNDER TERMINALS.
4. ALL TrueAlert SLC AND NAC WIRING CONNECTIONS ARE SUPERVISED AND POWER-LIMITED.
5. POWERING THE S/V FROM AN APPLIANCE POWER SOURCE LESS THAN 17 VDC OR GREATER THAN 32 VDC MAY CAUSE PERMANENT DAMAGE
TO THE S/V UNIT.
6. THE TrueAlert S/V CAN ONLY BE OPERATED THROUGH A 4009 TrueAlert ADDRESSABLE CONTROLLER OR TrueAlert COMPATIBLE FACP.
7. WHEN CONTROLLED FROM A 4009 TrueAlert ADDRESSABLE CONTROLLER, THE FACP SETTINGS ARE NOT SUPPORTED.
8. MAXIMUM T-TAPPING LENGTH IS 100 FEET.
CLEAR
WHITE
RED
AMBER/
BLUE
GREEN
RED
APPLIANCE
CONFIGURATION CONTROL
DIP SWITCH
ACCESSABLE FROM REAR
MAGNETIC TEST
LOCATION
NFPA 72 REQUIRES THAT
THE ENTIRE LENS BE NOT
LESS THAN 80" AND NOT
GREATER THAN 96" ABOVE
THE FINISHED FLOOR.
80"
MIN.
ADDRESS SETTING
DIP SWITCH
ACCESSABLE FROM REAR
SEMI-FLUSH MOUNTING
RESERVED FOR
FUTURE USE
LSB
MSB
0000
1000
0100
1 2 3 4
6 7 8
1100
DIP
SWITCHES
0=OFF
0010
1=ON
1 THRU 4
1010
NOT
USED
0110
1110
0001
CURRENT VALUES ARE UL 1971 MAX RATING FOR THE GIVEN VOLTAGE LEVEL
1001
30cd
75cd
15cd
135cd
185cd
VOLTAGE
110cd
0101
0.047
23 VRMS
0.208
0.057
0.100
0.160
0.132
1101
0.062
0.075
0.133
0.178
17 VRMS
**0.281
**0.214
0011
0.054
23 VRMS
0.211
0.078
0.128
0.184
1011
0.067
**0.282
0.103
0.171
17 VRMS
0.250
0111
NOT
*10cd
*20cd
*45cd
*95cd
*75cd
1111
SUPPORTED
23 VRMS
0.054
0.211
0.078
0.128
0.184
**0.282
17 VRMS
0.067
0.103
0.171
0.250
*3cd
*7cd
*15cd
*37cd
*30cd
23 VRMS
0.054
0.078
0.128
0.211
0.184
**0.282
0.067
17 VRMS
0.103
0.171
0.250
5
1000
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
0100
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
4" SQUARE x 1 1/2" DEEP BOX
(RACO NO. 231 OR 232)
SUPPLIED BY CONTRACTOR
NOTE: NO CONDUIT ENTRY IN
THE REAR OF THE BACK BOX
1. BRING THE BUILDING WIRING THROUGH THE RECTANGULAR OPENING IN THE BACKPLATE.
2. CONNECT THE BUILDING WIRES TO THE BACKPLATE.
3. SECURE THE BACKPLATE TO THE ELECTRICAL BOX BY USING THE PROVIDED HARDWARE.
INSTALLED WITH THE WRITING "INSTALL THIS SIDE UP" AT THE TOP.
G
WHITE
FIRE
5. SET THE APPLIANCE ADDRESS AND CONFIGURATION SETTINGS.
6. ATTACH THE ASSEMBLED APPLIANCE ONTO THE BACKPLATE.
49VO
2
1
CKT
-
1
-
49VO
2
CKT
1
+
-
49VO
2
CKT
SLC -
SLC SLC +
SLC +
FEATURES:
1
+
-
49VO
2
CKT
1
+
-
SLC -
SLC -
SLC +
SLC +
CKT
+
B
C
D
E
70.7V
F
G
25V
TB1
SPKR+
A
SPKR-
SPKR -
SLC -
STROBE +
STROBE +
STROBE +
STROBE -
STROBE -
STROBE -
2W
MODEL NUMBER
COVER
COLOR
4906-9202
RED
4906-9204
WHITE
RESERVED FOR
FUTURE USE
DIP SWITCHES 5 & 6
MSB
LSB
0000
1000
0100
1100
0010
1010
DIP SWITCHES 0110
1 THRU 4
1110
0001
1001
0101
1101
0011
1011
0111
1111
1000
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
0000
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
0100
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
1100
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
1 2 3 4 5 6 7 8
NOT
USED
0=OFF
1=ON
(RACO NO. 650)
3 1/2" X 1 1/2 " OR EQUAL
(88.9 mm x 38.1 mm)
HANDY BOX SUPPLIED BY CONTRACTOR
NOTE: DO NOT BRING CONDUIT THROUGH
THE REAR OF THE ELECTRICAL BOX
MAGNETIC TEST
LOCATION
011
57
03
51
PCAF
-
STROBE LED
+
CEILING MOUNT
MOUNTING NOTES:
1. THE TrueAlert CEILING STROBE UNIT ATTACHES DIRECTLY TO A STANDARD SINGLE-GANG,
ELECTRICAL BOX (NOT SUPPLIED), SEMI-FLUSH OR SURFACE MOUNTED.
2. THERE ARE TWO HOLES FOR ELECTRICAL BOX MOUNTING. SECURE THE HOUSING TO SINGLE-GANG BOX
USING 2 MOUNTING SCREWS (#6/32-INCH x 1 1/8-INCH LONG SUPPLIED) LINE THE MOUNTING TABS
OF THE STROBE UNIT TO THE HOUSING SLOTS AND SNAP INTO PLACE.
3. IT IS RECOMMENDED THAT THE STROBE ADDRESS BE SET BEFORE THE APPLIANCE IS SNAPPED TO THE
HOUSING.
4. ADDRESS SWITCH SW2 IS ACCESSIBLE WITH THE CEILING-MOUNT STROBE REMOVED.
4906 STROBE
TrueAlert STROBE UNIT REAR VIEW
FROM TrueAlert COMPATIBLE
SLC CONTROLLER (SEE WIRING NOTES)
SLC SLC +
4905-9989
WHITE SPEAKER COVER WITH RED "FIRE" LETTERING
DIMENSIONS
5 1/8"" H x 5" W x 1 1/2"D
(130 mm X 127 mm X 38 mm)
2
CKT
1
+
-
2
CKT
2
1
+
-
SLC -
SLC -
SLC -
SLC +
SLC +
SLC +
CKT
+
WIRING NOTES:
1. REFER TO FIELD WIRING DIAGRAMS OF THE DRIVING TRUEALERT COMPATIBLE CONTROLLER FOR ADDITIONAL SLC WIRING INFORMATION.
2. NOTIFICATION APPLIANCES ARE RATED PER INDIVIDUAL NAMEPLATE LABEL.
3. MAINTAIN CORRECT POLARITY ON TERMINAL CONNECTIONS. DO NOT LOOP WIRES UNDER TERMINALS.
4. ALL TrueAlert SLC WIRING CONNECTIONS ARE SUPERVISED AND POWER-LIMITED.
5. POWERING THE STROBE FROM AN APPLIANCE POWER SOURCE LESS THAN 17 VDC OR GREATER THAN 32 VDC MAY CAUSE PERMANENT DAMAGE TO
THE STROBE.
6. THE TrueAlert STROBE CAN ONLY BE OPERATED THROUGH A 4009 TrueAlert ADDRESSABLE CONTROLLER OR TrueAlert COMPATIBLE FACP.
7. WHEN CONTROLLED FROM A 4009 TrueAlert ADDRESSABLE CONTROLLER, THE FACP SETTINGS ARE NOT SUPPORTED.
8. MAXIMUM T-TAPPING LENGTH IS 100 FEET.
G
TrueAlert (STYLE Y) SPEAKER NOTIFICATION APPLIANCES 4902 SERIES
ARCHITECT'S STAMP
4" SQ. x 1 1/2" DEEP BOX
(101.6 mm x 38.1 mm)
(RACO NO. 191 OR EQUAL)
SUPPLIED BY CONTRACTOR
FIRE ALARM SPEAKERS WITH MODELS FOR WALL MOUNTING
UL LISTED TO STANDARD 1480
ULC LISTED MODEL (CA SUFFIX FOLLOWING THE MODEL NUMBER)
JUMPER
POSITION
J1 TO TAP A
J1 TO TAP B
J1 TO TAP C
J1 TO TAP D
J1 TO TAP D
J1 TO TAP E
J1 TO TAP F
J1 TO TAP G
CAPACITOR INPUT FOR CONNECTION TO SUPERVISED NOTIFICATION
APPLIANCE CIRCUIT
RUGGED , HIGH IMPACT, FLAME RETARDANT THERMOPLASTIC
HOUSING
OFF-WHITE COLOR (NO LETTERING)
FLUSH MOUNT ON CEILING OR WALL
COMPATIBLE WITH OPTIONAL TILE BRIDGE 2905-9946
SPKR-
TB1
SPKR+
WATTAGE
SETTING
1/4
1/2
70.7VRMS
1
2
1/4
1/2
25VRMS
1
2
PROJECT
CONTACT
SPKR +
IF LAST APPLIANCE
ON CIRCUIT,
CONNECT EOLR
(SEE WINING NOTES)
2. ENSURE CORRECT ORIENTATION OF BOX WITH EXTENSION IN RELATION TO LOCATION OF
MOUNTING SCREWS.
3. FOR INSTALLATION IN PLASTER OR CONCRETE CEILING, MOUNT BOX WITH EXTENSION FLUSH
OR WITH MAXIMUM 1/4 INCH RECESS; FOR SUSPENDED CEILING, USE A SUITABLE BRIDGE
THAT RESTS ON TILE SUPPORT BOX WITH EXTENSION.
SOUND OUTPUT RATINGS @ 10 FT. (3m)
SELECTED TAP
1/4W 1/2W 1W
J
2W
PRODUCT SELECTION SPEAKER MOUNTING ADAPTERS AND BOXES
MODEL
DESCRIPTION
NUMBER
ROUND HOUSING SPEAKER, CEILING
4902-9721(CA)
OFF-WHITE (NO LETTERING)
OR WALL MOUNT
MOUNTING ADAPTERS
MODEL
DESCRIPTION
NUMBER
TILE BRIDGE
2905-9946
1. REFER TO FIELD WIRING DIAGRAMS SUPPLIED WITH THE 4100/4003 FOR ADDITIONAL NAC WIRING INFORMATION.
2. NOTIFICATION APPLIANCES ARE RATED PER INDIVIDUAL NAMEPLATE LABEL.
3. MAINTAIN CORRECT POLARITY ON TERMINAL CONNECTIONS. DO NOT LOOP WIRES UNDER TERMINALS.
4. ALL NAC WIRING CONNECTIONS ARE SUPERVISED AND POWER-LIMITED.
5. END-OF-LINE RESISTOR VALUE DEPENDENT ON CONTROL PANEL.
717 Market Street
Suite 500
San Francisco, CA 94103
TEL
415.489.7240
FAX
415.489.7289
www.interfaceengineering.com
MOUNTING NOTES:
1. THE TrueAlert CEILING-MOUNT SPEAKER ATTACHES DIRECTLY TO A STANDARD 4-INCH
SQUARE ELECTRICAL BOX WITH EXTENSION RING (NOT SUPPLIED) SEMI-FLUSH MOUNTED
OR SURFACE MOUNTED.
BLACK
D
PRO
F E S S I ON
ON LA
AS
AL
No. E16806
AT
EL
E CT RICA N
E O
OR
F CAL I F
DETAILS - FIRE ALARM
BLACK
SPKR -
SPKR -
SPKR +
SPKR +
25 VRMS OR 70.7 VRMS
AUDIO INPUT FROM 4100/4003
WIRING NOTES:
E N G I N E E R I N G
SEMI-FLUSH MOUNTING
CEILING OR WALL
NOTE: ULC LISTED MODELS ARE DESIGNATED WITH A "CA" SUFFIX.
RED
2014-0174
Joe Ripp
INTERFACE
TrueAlert CEILING MOUNTED SPEAKER REAR VIEW
(SHOWN TAPPED AT 1/2 WATT @ 25VRMS)
REVERBERANT CHAMBER, UL 1480 TEST 79 dBA 82 dBA 85 dBA 88 dBA
4902-9721(CA)
ROUND HOUSING ANECHOIC CHAMBER, ON-AXIS, ULC S541 79 dBA 82 dBA 85 dBA 88 dBA
SPKR +
H
CONSULTANT
DEPTH INTO BOX: 2 3/4" (70 MM)
INPUT VOLTAGE: 25 OR 70.7 VRMS
POWER TAPS: 1/4, 1/2, 1 AND 2W
INPUT TERMINAL RATINGS: 18 TO 12 AWG
FREQUENCY (FIRE ALARM): 400 TO 4000 Hz
RESPONSE (GENERAL SIGNALING): 125 TO 12 kHz
TEMPERATURE RANGE: 32° TO 100 ° F ( 0° TO 38° C)
HUMIDITY RANGE: 10% TO 95% RH FROM 32° TO 122° F
(0 ° TO 50° C)
BLACK
SPKR -
THIS DRAWING IS NOT FINAL OR TO BE USED FOR CONSTRUCTION UNTIL IT IS SIGNED BY THE ARCHITECT
AND ENGINEER.
VOLTAGE
SPECIFICATIONS:
MOUNTING NOTES:
SPKR -
THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO LPAS, INC. AND IS FURNISHED FOR THE
PURPOSES OF REVIEW, BIDDING OR CONSTRUCTION OF THE PROJECT LISTED IN THE JOB TITLE BOX ABOVE
AND SHALL NOT BE USED FOR ANY OTHER PURPOSE OR RELEASED TO ANY OTHER PARTY WITHOUT THE
WRITTEN CONSENT OF LPAS, INC. INFOMATION CONTAINED HEREIN IS AN INSTRUMENT OF PROFESSIONAL
SERVICES AND SHALL REMAIN THE PROPERTY OF LPAS, INC. ALL RIGHTS RESERVED COPYRIGHT © 2009.
(38.1 mm)
1 1/2" EXTENSION RING
(RACO NO. 203 OR EQUAL)
SUPPLIED BY CONTRACTOR
TrueAlert SPEAKER
JUMPER SETTINGS
APPROVAL
I NE ER
COVERS (FOR REPLACEMENT OR COLOR CONVERSION)
MODEL
DESCRIPTION
NUMBER
RED SPEAKER COVER WITH WHITE "FIRE" LETTERING
4905-9988
-
U
WHITE
USE TO COVER SURFACE MOUNTED
1 1/2" DEEP WITH 1 1/2" DEEP EXTENSION,
ALL EXTERNAL TO WALL
1
+
4906 STROBE
4906 STROBE
ST
K
RED
DIMENSIONS
5 3/8" H x 5 1/4" W x 3 3/16" D
(136 mm x 133 mm x 81 mm)
TOTAL SURFACE DEPTH WITH
SPEAKER = 4 5/8" (117 mm)
CKT
FEATURES:
4" SQ. X 1 1/2" DEEP BOX
(101.6mm X 38.1mm)
(RACO NO. 191)
SUPPLIED BY CONTRACTOR
25 VRMS OR 70.7 VRMS
AUDIO INPUT FROM
4100/4003
(SEE WIRING NOTES)
4906 STROBE
2
1
-
IN/OUT WIRING TERMINALS FOR 18 AWG TO 12 AWG
RED
DESCRIPTION
E
F
MOUNTS TO 4" SQUARE OUTLET BOX, 1 1/2' DEEP WITH
1 1/2" DEEP BOX EXTENSION
NOTE: ULC LISTED MODELS ARE DESIGNATED WITH A "CA" SUFFIX.
MOUNTING ADAPTERS
MODEL
NUMBER
4905-9941
SURFACE MOUNT ADAPTER
SKIRTS (DEEP)
4905-9942
INTENSITY SELECTION
PLUG, ACCESSIBLE
ONLY FROM REAR OF
HOUSING; FACTORY
SETTING IS FACP
STROBE INTENSITY SETTING
VIEWABLE THROUGH THE LENS
CKT
CKT
INPUT INPUT
LETTERING
CURRENT VALUES ARE UL 1971 MAX RATING
COLOR
15cd
30cd
75cd
VOLTAGE
110cd
0.060
0.092
0.180
0.240
23 VRMS
WHITE
17 VRMS
0.076
0.128
0.242
0.328
23 VRMS
0.060
0.092
0.180
0.240
RED
17 VRMS
0.076
0.328
0.128
0.242
PRODUCT INFORMATION
MODEL
5 1/8" H x 5 " W x 1 1/2" D
(130 mm X 127 mm X 38 mm)
DATE
(ERICO NO. 512), T-BAR
WITH CLIPS AND SCREWS
SUPPLIED BY CONTRACTOR
TrueAlert STROBE UNITS- DIP SWITCH ADDRESS CHART
FOUR INCH CONE (102mm) PROVIDES HIGH QUALITY TONE
AND VOICE REPRODUCTION
MULTI-TAPPED DESIGN PROVIDES OUTPUT POWER OF 1/4,
1/2, 1, OR 2 W WITH EITHER 25 OR 70.7 VRMS INPUT
BLACK
DIMENSIONS
ISSUE
D
3. VOLTAGE DROPS AND STANDBY BATTERY CALCULATIONS SHOULD BE MADE USING ANTICIPATED OPERATING CONDITIONS.
OPERATION ABOVE 24VRMS DRAWS LESS CURRENT.
1. THE TrueAlert WALL-MOUNT SPEAKER ATTACHES DIRECTLY TO A STANDARD 4-INCH
ELECTRICAL BOX WITH EXTENSION RING (NOT SUPPLIED) FLUSH MOUNTED OR SURFACE
MOUNTED. MOUNTING THE SPEAKER TO THE 4-INCH SQUARE ELECTRICAL BOX IS SHOWN.
ATTACH THE SPEAKER TO THE ELECTRICAL BOX USING TWO SCREWS (SUPPLIED) MOUNTED
CROSS CORNER.
2. TO REMOVE THE COVER PRESS THE SNAP RELEASE IN THE BOTTOM OF THE SPEAKER
WITH A FLAT TIP SCREWDRIVER WHILE PULLING THE COVER UP WITH THE OTHER HAND.
3. NAC TERMINALS (CKT+, CKT-) ARE NOT ACCESSIBLE THROUGH THE FRONT AFTER
MOUNTING.
PRODUCT SELECTION SPEAKER MOUNTING ADAPTERS AND BOXES
MODEL
DESCRIPTION
NUMBER
4902-9716(CA)
RED WITH WHITE "FIRE" LETTERING
RECTANGULAR HOUSING, WALL
MOUNT
SPEAKER
4902-9717(CA)
WHITE WITH RED "FIRE" LETTERING
NO.
TM
TrueAlert
(STYLE 4) VISIBLE NOTIFICATION APPLIANCES 4906 SERIES
1. TrueAlert APPLIANCES ARE REQUIRED TO BE CONNECTED TO A TrueAlert ADDRESSABLE CHANNEL WHERE
BOTH POWER AND ADDRESSED COMMUNICATIONS ARE SUPPLIED. REFER TO DATA SHEET S4009-0003,
(TrueAlert ADDRESSABLE CONTROLLER) FOR ADDITIONAL INFORMATION ABOUT WIRING RULES AND DISTANCE
LIMITATIONS.
2. THE RATED RANGE LISTED IS THE ABSOLUTE OPERATING VOLTAGE RANGE. OPERATION OUTSIDE OF
THIS RANGE MAY CAUSE PERMANENT DAMAGE TO THE APPLIANCE. PLEASE NOTE THAT 17 VRMS IS
THE LOWEST OPERATING VOLTAGE THAT IS ALLOWED AT THE LAST APPLIANCE ON THE TRUEAlert
NOTIFICATION APPLIANCE CIRCUIT UNDER WORST CASE CONDITIONS. VOLTAGE DROP AND STANDBY
BATTERY CALCULATIONS SHOULD BE MADE USING ANTICIPATED OPERATING CONDITIONS. "LOW" HORN
SETTING DRAWS APPROXIMATELY 5 mA LESS CURRENT AT EACH VOLTAGE LISTED.
SEMI-FLUSH MOUNTING
SELECTED TAP
1/4W 1/2W 1W 2W
MODEL
4902-9716(CA),
REVERBERANT CHAMBER, UL 1480 TEST 78 dBA 81 dBA 84 dBA 87 dBA
4902-9717(CA)
RECT. HOUSING ANECHOIC CHAMBER, ON-AXIS, 1kHz INPUT 87 dBA 90 dBA 93 dBA 96 dBA
SLC SLC +
1. REFER TO FIELD WIRING DIAGRAMS OF THE DRIVING TrueAlert COMPATIBLE CONTROLLER FOR ADDITIONAL SLC WIRING INFORMATION.
REFER TO THE FIELD WIRING DIAGRAMS SUPPLIED WITH THE 4100/4003 FOR ADDITIONAL NAC WIRING INFORMATION.
2. NOTIFICATION APPLIANCES ARE RATED PER INDIVIDUAL NAMEPLATE LABEL.
3. MAINTAIN CORRECT POLARITY ON TERMINAL CONNECTIONS. DO NOT LOOP WIRES UNDER TERMINALS.
4. ALL TrueAlert SLC AND NAC WIRING CONNECTIONS ARE SUPERVISED AND POWER-LIMITED.
5. POWERING THE S/V FROM AN APPLIANCE POWER SOURCE LESS THAN 17 VDC OR GREATER THAN 32 VDC MAY CAUSE PERMANENT DAMAGE
TO THE S/V UNIT.
6. THE TrueAlert S/V CAN ONLY BE OPERATED THROUGH A 4009 TrueAlert ADDRESSABLE CONTROLLER OR TrueAlert COMPATIBLE FACP.
7. WHEN CONTROLLED FROM A 4009 TrueAlert ADDRESSABLE CONTROLLER, THE FACP SETTING IS NOT SUPPORTED.
8. MAXIMUM T-TAPPING LENGTH IS 100 FEET.
SOUND OUTPUT RATINGS @ 10 FT. (3m)
J
C
TM
WATTAGE
SETTING
1/4
1/2
70.7VRMS
1
2
1/4
1/2
25VRMS
1
2
HUMIDITY RANGE: 10% TO 95% RH FROM 32° TO 122° F
(0 ° TO 50° C)
SPKR -
WIRING NOTES:
SPECIFICATION NOTES:
VOLTAGE
DEPTH INTO BOX: 2 3/4" (70 MM)
INPUT VOLTAGE: 25 OR 70.7 VRMS
POWER TAPS: 1/4, 1/2, 1 AND 2W
INPUT TERMINAL RATINGS: 18 TO 12 AWG
FREQUENCY (FIRE ALARM): 400 TO 4000 Hz
RESPONSE (GENERAL SIGNALING): 125 TO 12 k Hz
TEMPERATURE RANGE: 32° TO 100 ° F ( 0° TO 38° C)
SPKR -
ENG
SPECIFICATIONS:
SPKR +
SLC +
TEMPERATURE RANGE: 32° TO 122° F (O° TO 50° C)
HUMIDITY RANGE: 10% TO 93% NON-CONDENSING AT 100° F (38° C)
CONNECTIONS: TERMINAL BLOCKS FOR 18 TO 12 AWG
2
TrueAlert SPEAKER
JUMPER SETTINGS
TrueAlert WALL MOUNTED SPEAKER BACK VIEW
(SHOWN TAPPED AT 1/2 WATT @ 25 VRMS)
SPKR +
HOUSING DIMENSIONS (INCLUDING LENS): 4 3/4" x 2 5/16" x 2 5/8" D
(121 mm x 75 mm x 67 mm)
1 1/2" DEEP EXTENSION
(38.1mm)
(RACO NO. 203)
SUPPLIED BY CONTRACTOR
J1
H
4906 S/V
SPKR +
SLC -
84.3 87.1* 89.7*
TM
JUMPER
POSITION
J1 TO TAP A
J1 TO TAP B
J1 TO TAP C
J1 TO TAP D
J1 TO TAP D
J1 TO TAP E
J1 TO TAP F
J1 TO TAP G
4906 S/V
SAN JOSE, CALIFORNIA
END-OF-LINE
RESISTOR (VALUE
DEPENDANT ON
FACP)
4906 S/V
GENERAL SPECIFICATIONS:
TrueAlert (STYLE Y) SPEAKER NOTIFICATION APPLIANCES 4902 SERIES
FIRE ALARM SPEAKERS WITH MODELS FOR WALL MOUNTING
UL LISTED TO STANDARD 1480
ULC LISTED MODELS (CA SUFFIX FOLLOWING THE MODEL NUMBER)
FOUR INCH CONE (102mm) PROVIDES HIGH QUALITY TONE
AND VOICE REPRODUCTION
MULTI-TAPPED DESIGN PROVIDES OUTPUT POWER OF 1/4,
1/2, 1, 2 W WITH EITHER 25 OR 70.7 VRMS INPUT
IN/OUT WIRING TERMINALS FOR 18 AWG TO 12 AWG
MOUNTS TO 4" SQUARE OUTLET BOX, 1 1/2' DEEP WITH
1 1/2" DEEP BOX EXTENSION
CAPACITOR INPUT FOR CONNECTION TO SUPERVISED NOTIFICATION
APPLIANCE CIRCUIT
RUGGED, HIGH IMPACT, FLAME RETARDANT THERMOPLASTIC
HOUSING
APPEARANCE THAT COMPLEMENTS TrueAlert STROBES AND
SPEAKER/STROBES
RED OR WHITE HOUSING WITH "FIRE" LETTERING
SURFACE OR SEMI-FLUSH WALL MOUNT
OPTIONAL MATCHING ADAPTER SKIRTS FOR COVERING SURFACE
MOUNTED ELECTRICAL BOXES
SPKR +
* PERFORMANCE REFERENCE, NOMINAL AVERAGE CURRENTS WITH STROBES FLASHING
+
6. THE TrueAlert V/O CAN ONLY BE OPERATED THROUGH A 4009 TrueAlert ADDRESSABLE CONTROLLER OR TrueAlert COMPATIBLE FACP.
PRODUCT INFORMATION
SPKR -
SPKR +
SPKR +
SPKR -
FROM TRUEALERT-COMPATIBLE
SLC CONTROLLER (SEE WIRING NOTES)
4. ATTACH THE COVER TO THE APPLIANCE.
1. REFER TO FIELD WIRING DIAGRAMS OF THE DRIVING TrueAlert COMPATIBLE CONTROLLER FOR ADDITIONAL SLC WIRING INFORMATION.
2. NOTIFICATION APPLIANCES ARE RATED PER INDIVIDUAL NAMEPLATE LABEL.
3. MAINTAIN CORRECT POLARITY ON TERMINAL CONNECTIONS. DO NOT LOOP WIRES UNDER TERMINALS.
4. ALL TrueAlert SLC WIRING CONNECTIONS ARE SUPERVISED AND POWER-LIMITED.
5. POWERING THE V/O FROM AN APPLIANCE POWER SOURCE LESS THAN 17 VDC OR GREATER THAN 32 VDC MAY CAUSE PERMANENT DAMAGE.
TO THE V/O UNIT.
(130 mm X 127 mm X 67 mm)
4906-9257
SPKR -
SLC +
*CURRENT DRAWS REFLECT STROBE FLASHING
WIRING NOTES:
HOUSING DIMENSIONS (INCLUDING LENS): 5 1/8" H X 5" W X 2 5/8" D
TEMPERATURE RANGE: 32° TO 120° F (O° TO 49° C)
HUMIDITY RANGE: 10% TO 93% NON-CONDENSING AT 104° F (40° C)
CONNECTIONS: TERMINAL BLOCKS FOR 18 TO 12 AWG
ALERT
NOT
USED
0=OFF
FROM AUDIO NAC CHANNEL
(4100/4003) (SEE WIRING NOTES)
STROBE:
CANDELA SELECTION PLUG
RATED VOLTAGE RANGE: 17 TO 31 VDC
SUPERVISORY REQUIREMENTS: 1 UNIT LOAD
STROBE FLASH RATE: 1 Hz
SYNCHRONIZED SLC LOADING: UP TO 43 TRUEAlert ADDRESSABLE SYNCHRONIZED STROBES MAXIMUM PER SLC
MOUNTING INSTRUCTIONS:
1100
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
* VISIBLE OUTPUT RATING FOR THE GIVEN LENS COVER COLOR AT THE APPLIANCE SETTING.
** 17 VOLT CURRENT SHOWN AT THE HIGH CANDELA SETTINGS IS FOR USE WITH 4009T ONLY.
GENERAL SPECIFICATIONS:
WHITE
PHYSICAL EDUCATION BUILDING AND
RENOVATED LAB BUILDING
SPECIFICATIONS:
49VO
FROM TrueAlert COMPATIBLE
SLC CONTROLLER (SEE NOTES)
4906-9256
INDIVIDUALLY ADDRESSED HIGH INTENSITY VISIBLE
NOTIFICATION APPLIANCE (STROBE) PROVIDES:
SUPERVISION OF EACH INDIVIDUAL APPLIANCE'S WIRING AND
CONNECTIONS
ABILITY TO CONNECT USING "T" TAPPING FOR CLASS B/STYLE 4
CIRCUITS TO SIMPLIFY WIRING.
COMPATIBILITY WITH ADA REQUIREMENTS
MAGNETIC TEST DIAGNOSTICS TO ASSIST CHECKOUT AND
TESTING OF APPLIANCES AND WIRING
XENON STROBE OUTPUT IS MANUALLY SELECTABLE FOR 15, 30,
75, 110 CANDELA OR "FACP". THE "FACP" SETTING ALLOWS THE
4100U TO PROGRAM THE CANDELA SETTING.
UL LISTED TO STANDARD 1971
LED INDICATOR AND MAGNETIC TEST FEATURE:
LED INDICTOR CAN BE SELECTED TO DISPLAY EACH POLLING CYCLE
TO INDICATE APPLIANCE SUPERVISION
WHEN THE TrueAlert CONTROLLER IS IN DIAGNOSTIC MODE, THE
MAGNETIC TEST PULSES THE LED TO INDICATE APPLIANCE ADDRESS
AND IS SELECTABLE TO ALSO BRIEFLY FLASH THE STROBE TO
CONFIRM OPERATION
TrueAlert NOTIFICATION APPLIANCE DESIGN PROVIDES
FLEXIBLE, EASY, AND CONVENIENT FLUSH OF SURFACE
WALL BOX MOUNTING:
REAR OF HOUSING DOES NOT EXTEND INTO BOX AND EASILY MOUNTS
TO SINGLE GANG ELECTRICAL BOX
DIP SWITCHES 5 & 6
0000
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
BLANK
1=ON
SAN JOSE CITY
COLLEGE
STROBE INTENSITY SETTING
VIEWABLE THROUGH THE LENS
FEATURES:
STROBE INTENSITY SETTING
VIEWABLE THROUGH THE
RIGHT SIDE OF THE COVER
TrueAlert V/O UNITS- DIP SWITCH ADDRESS CHART
WHITE
- ANECHOIC CHAMBER, ULC-S541 TESTING, 25 VRMS 81.6
WHEN SURFACE MOUNTING USE
RED SKIRT NO. 4905-9937
OR WHITE SKIRT NO. 4905-9940
INTENSITY SELECTION
PLUG, ACCESSIBLE
ONLY FROM REAR OF
HOUSING; FACTORY
SETTING IS FACP.
CONTROLLED BY PANEL.
581
531
PCAF
51
03
57
011
4906-9255
PRODUCT INFORMATION
BACKPLATE
BOTTOM OF LENS
IS EITHER EVEN WITH
OR SLIGHTLY ABOVE
BOTTOM OF
COMPATABLE BOXES
FIRE
011
57
03
51
PCAF
MSB
- ANECHOIC CHAMBER, ULC-S541 TESTING, 70.7 VRMS 80.9 84.1 87.3* 90.2*
- UL STANDARD 1480 SPEAKER OUTPUT RATING CATEGORIES ARE BASED UPON 3 dBA INCREMENTS.
- SELECT TAPS AS INDICATED TO SATISFY FOR ULC FIRE ALARM APPLICATION REQUIREMENT OF 85 dBA MINIMUM.
- SPEAKERS ARE NOT ADDRESSABLE AND ARE FOR CONNECTION TO CONVENTIONAL FIRE ALARM AUDIO CIRCUITS.
IMPORTANT!
WALL MOUNT INSTALLATION
HEIGHT REFERENCE
ELECTRICAL
BOX OUTLINE
WHITE
CURRENT VALUES ARE UL 1971 MAX RATING
LETTERING
COLOR
15cd
30cd
75cd
VOLTAGE
110cd
0.060
0.092
0.180
0.240
23 VRMS
RED
17 VRMS
0.076
0.128
0.242
0.328
23 VRMS
0.060
0.092
0.180
0.240
17 VRMS
0.076
0.128
0.242
0.328
23 VRMS
0.060
0.092
0.180
0.240
RED
17 VRMS
0.076
0.128
0.242
0.328
23 VRMS
0.060
0.092
0.180
0.240
RED
17 VRMS
0.076
0.128
0.242
0.328
- WATTAGE TAP (25 VRMS OR 70.7 VRMS INPUT) 1/4W 1/2W 1W
- REVERBERANT CHAMBER, UL 1480 TEST
76 79 82 85
OPTIONAL
LENS COVER FOR
COLORED LENS
COVER
4906-9254
B
INTENSITY SELECTION
PLUG, ACCESSIBLE
ONLY FROM REAR OF
HOUSING; FACTORY
SETTING IS FACP
1 2 3 4 5 6 7 8
SPEAKER
- INPUT VOLTAGE: 25 OR 70.7 VRMS, SEE NOTE 4
- POWER TAPS: 1/4, 1/2, 1W, AND 2W
- FREQUENCY RESPONSE:
FIRE ALARM: 400 TO 4000 Hz
SPEAKER OUTPUT RATINGS (dBA @ 10 FT. (3m)
SLC SLC +
SLC +
LETTERING
ADDRESS SETTING DIP SWITCH IS BEHIND
STROBE ASSEMBLY; SELECT ADDRESS BEFORE
INSERTING INTO HOUSING.
DIP SWITCHES 1 ~ 6 ARE USED TO SET ADDRESS.
DIP SWITCHES 7 AND 8 ARE NOT USED AND
SHOULD BE SET TO "OFF".
L
SPKR +
SPKR -
MODEL NUMBER
SPKR +
SPKR +
COVER
COLOR
MAGNETIC TEST
LOCATION
IA
LETTERING LENS
COLOR
COLOR
WHITE
SPKR -
SPKR -
NOT
USED
LSB
1100
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
J
STROBE:
RATED VOLTAGE RANGE: 17 TO 31 VRMS
SUPERVISORY REQUIREMENTS: 1 UNIT LOAD
STROBE FLASH RATE: 1 Hz
49VO-WWF(-BA)
1. THE TrueAlert S/V ATTACHES DIRECTLY TO A STANDARD 4-INCH ELECTRICAL BOX (NOT SUPPLIED), FLUSH MOUNTED
OR SURFACE MOUNTED.
2. THERE ARE FOUR HOLES FOR 4-INCH SQUARE ELECTRICAL BOX MOUNTING. SECURE THE HOUSING TO THE BOX USING
TWO MOUNTING SCREWS. THE TWO MOUNTING SCREWS ARE PLACED CROSS CORNER (OPPOSITE TOP AND BOTTOM HOLES)
3. TO REMOVE THE COVER, PRESS THE SNAP RELEASE IN (ONE AT A TIME) WITH A FLAT TIP SCREWDRIVER WHILE PULLING
UP THE COVER WITH THE OTHER HAND. ADDRESS SWITCH (SW1 IS ACCESSIBLE WITH THE COVER REMOVED).
0100
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
1 2 3 4 5 6 7 8
SPECIFICATIONS:
RED
STROBE INTENSITY SETTING
VIEWABLE THROUGH THE LENS
SEMI-FLUSH MOUNTING
MOUNTING NOTES:
APPLIANCE CONFIGURATION SETTINGS
POSITION 1: CONFIGURATION CONTROL - LOCAL (OFF), PANEL (ON)
POSITION 2: AUDIBLE VOLUME - HIGH (OFF), LOW (ON)
POSITION 3: CANADIAN HORN MODE - SET TO OFF
POSITION 4: LEGACY NAC MODE - SET TO OFF
POSITION 5,6,7: UNUSED - SET TO OFF
POSITION 8: CLEAR/COLOR LENS - ALARM (OFF), ALERT (ON)
LED INDICATOR AND MAGNETIC TEST FEATURE:
LED INDICTOR CAN BE ELECTED TO DISPLAY EACH POLLING CYCLE
TO INDICICATE APPLIANCE SUPERVISION
WHEN THE TrueAlert CONTROLLER IS IN DIAGNOSTIC MODE, THE
MAGNETIC TEST PULSES THE LED TO INDICATE APPLIANCE ADDRESS
AND IS SELECTABLE TO ALSO BRIEFLY FLASH THE STROBE TO
CONFIRM OPERATION
49VO-WRF(-BA)
SPEAKER HOUSING DIMENSIONS : 7 1/2" DIA. X 1/2"D (191MM X 13MM)
STROBE LENS PROTRUSION DIMENSIONS : 2 5/8" (67MM) ABOVE SPEAKER HOUSING
TEMPERATURE RANGE: 32° F TO 122° F (0° TO 50° C)
HUMIDITY RANGE: 10% TO 93% NON-CONDENSING AT 100° F (38° C)
DEPTH INTO BOX 2 3/4" (70MM)
SPEAKER TAP SELECTION: SINGLE JUMPER WIRE WITH PRESSURE CONNECTOR
ATTACHES TO ONE OF 8 TERMINALS
CONNECTIONS: TERMINALS FOR 18 TO 12 AWG, SEPARATE TERMINALS
FOR SPEAKER AND TrueAlert STROBE CONNECTION
STROBE
- RATED VOLTAGE: 17 TO 31 VRMS
- SUPERVISORY REQUIREMENTS: 1 UNIT LOAD
- STROBE FLASH RATE: 1Hz
- SYNCHRONIZED SLC LOADING: UP TO 43 TrueAlert ADDRESSABLE SYNCHRONIZED STROBES
MAXIMUM PER SLC
TM
TrueAlert
ES (STYLE 4 SLC) VISIBLE ONLY NOTIFICATION APPLIANCES 49VO SERIES
TrueAlert 2-WIRE ADDRESSABLE CONTROL OF VISIBLE
AND AUDIBLE NOTIFICATION ACTIVATES APPLIANCES WITH:
HORNS SOUNDED AS TEMPORAL OR MARCH TIME PATTERN, OR ON
CONTINUOUSLY, CONTROLLED SEPARATELY FROM VISIBLE APPLIANCES
ON THE SAME TWO-WIRE CIRCUIT
F
GENERAL SPECIFICATIONS:
SLC +
TrueAlert SPEAKER
JUMPER SETTINGS
INDIVIDUALLY ADDRESSED WALL MOUNT VISIBLE
NOTIFICATION APPLIANCES WITH EFFICIENT ELECTRONIC
HIGH INTENSITY XENON STROBE PROVIDES:
SUPERVISION OF EACH INDIVIDUAL APPLIANCE'S WIRING AND
CONNECTIONS
ABILITY TO CONNECT USING "T" TAPPING FOR CLASS B/STYLE 4
CIRCUITS TO SIMPLIFY WIRING
HORNS CONTROLLED SEPARATELY FROM STROBES ON THE SAME
2-WIRE CIRCUIT ALLOWING "ON-UNTIL-SILENCED" AND
"ON-UNTIL RESET".
XENON STROBE OUTPUT IS MANUALLY SELECTABLE FOR 15, 30, 75,
110, 135 AND 185 CANDELA OR "FACP". THE "FACP" SETTING ALLOWS
THE 4100 TO PROGRAM THE CANDELA SETTING.
IN/OUT WIRING ACCESSIBILITY FROM FRONT OF HOUSING PROVIDES
EASY ACCESS FOR INSTALLATION, INSPECTION, AND TESTING
MAGNETIC TEST DIAGNOSTICS TO ASSIST CHECKOUT AND TESTING
OF APPLIANCES AND WIRING
UL LISTED TO STANDARD 1971
COVER
COLOR
DIP SWITCHES
(SW1)
MAGNETIC TEST LOCATION
FROM TRUEALERT-COMPATIBLE
SLC CONTROLLER (SEE WIRING NOTES)
- UL STANDARD 1480 SPEAKER OUTPUT RATING CATEGORIES ARE BASED UPON 3 dBA INCREMENTS.
- SPEAKERS ARE NOT ADDRESSABLE AND ARE FOR CONNECTION TO CONVENTIONAL FIRE ALARM AUDIO CIRCUITS.
MODEL NUMBER
82"
MIN.
FROM AUDIO NAC CHANNEL
(4100/4003) (SEE WIRING NOTES)
- WATTAGE TAP (25 VRMS OR 70.7 VRMS INPUT) 1/4W 1/2W 1W 2W
- REVERBERANT CHAMBER, UL 1480 TEST
76 79 82 85
- ANECHOIC CHAMBER, ON-AXIS, 1kHz INPUT
87 90 93 96
E
011
57
03
51
PCAF
NFPA 72 REQUIRES THAT
THE ENTIRE LENS BE NOT
LESS THAN 80" AND NOT
GREATER THAN 96" ABOVE
THE FINISHED FLOOR.
4906 S/V
GENERAL SIGNALING: 125 TO 12 kHz
SPEAKER OUTPUT RATINGS (dBA @ 10 FT. (3m)
D
78-1/2"
MIN.
1 2 3 4 5 6 7 8
0=OFF
INTENSITY SELECTION
PLUG, ACCESSIBLE
ONLY FROM REAR OF
HOUSING; FACTORY
SETTING IS FACP
1-1/2"
MSB
1=ON
JUMPER LOCATED ON BACK
OF APPLIANCE
CL
1000
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
0000
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
0000
1000
0100
1100
0010
1010
DIP SWITCHES 0110
1 THRU 4
1110
0001
1001
0101
1101
0011
1011
0111
1111
ADDRESS SWITCH
SW2
LSB
4" SQUARE BOX OUTLINE
4"
2975-9145
BOX OUTLINE
1100
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
G
0000
1000
0100
1100
0010
1010
DIP SWITCHES 0110
1 THRU 4
1110
0001
1001
0101
1101
0011
1011
0111
1111
0100
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
DIP SWITCHES 5 & 6
F
1000
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
0000
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
RESERVED FOR
FUTURE USE
25V
DIP SWITCHES 5 & 6
WIRING INPUT TERMINALS AND SPEAKER
TAP SELECTION ARE ACCESSIBLE FROM
REAR OF SPEAKER HOUSING.
TrueAlert S/V UNITS- DIP SWITCH ADDRESS CHART
E
TrueAlert S/V UNITS- DIP SWITCH ADDRESS CHART
STROBE
- RATED VOLTAGE: 17 TO 31 VRMS
- SUPERVISORY REQUIREMENTS: 1 UNIT LOAD
- STROBE FLASH RATE: 1Hz
- SYNCHRONIZED SLC LOADING: UP TO 43 TrueAlert ADDRESSABLE SYNCHRONIZED STROBES
MAXIMUM PER SLC
*CURRENT DRAWS REFLECT STROBE FLASHING
COVER LETTERING
CURRENT VALUES ARE UL 1971 MAX RATING
MODEL NUMBER COLOR
COLOR
15cd
30cd
75cd
VOLTAGE
110cd
0.060
0.240
0.092
0.180
23 VRMS
4906-9251
RED
WHITE
17 VRMS
0.076
0.328
0.128
0.242
23 VRMS
0.060
0.092
0.180
0.240
WHITE
RED
4906-9253
17 VRMS
0.076
0.328
0.128
0.242
PRODUCT INFORMATION
FEATURES:
IMPORTANT!
WALL MOUNT INSTALLATION
HEIGHT REFERENCE
A
1 1/2" DEEP EXTENSION
(38.1mm)
(RACO NO. 203)
SUPPLIED BY CONTRACTOR
CAUTION: DO NOT BRING CONDUIT THROUGH
BACK OF ELECTRICAL BOX.
RE
WHITE S/V COVER WITH RED "FIRE" LETTERING
GENERAL SPECIFICATIONS:
SPEAKER
- INPUT VOLTAGE: 25 OR 70.7 VRMS, SEE NOTE 4
- POWER TAPS: 1/4, 1/2, 1W, AND 2W
- FREQUENCY RESPONSE:
FIRE ALARM: 400 TO 4000 Hz
7 1/4" H X 5" W X 1 3/8"D
(184 mm X 127 mm X 35 mm)
WATTAGE
SETTING
1/4
1/2
70.7VRMS
1
2
1/4
1/2
25VRMS
1
2
VOLTAGE
R EG I S T E
RED S/V COVER WITH WHITE "FIRE" LETTERING
DIMENSIONS (INCLUDING LENS) : 7 1/4" (184mm) H X 5" (127mm) W X 2 5/8" (67mm) D
TEMPERATURE RANGE: 32° F TO 122° F (0° TO 50° C)
HUMIDITY RANGE: 10% TO 93% NON-CONDENSING AT 100° F (38° C)
DEPTH INTO BOX: 2 1/2" (64mm)
SPEAKER TAP SELECTION: SINGLE JUMPER WIRE WITH PRESSURE CONNECTOR
ATTACHES TO ONE OF 8 TERMINALS
CONNECTIONS: TERMINALS FOR 18 TO 12 AWG, SEPARATE TERMINALS
FOR SPEAKER AND TrueAlert STROBE CONNECTION
FOR VISIBLE LENS MOUNTING HIEGHT TO MEET "ADA" 80" MINIMUM, THE 4" SQUARE BACKBOX
IS TO BE INSTALLED AT A HIEGHT OF 82" FROM THE FLOOR TO THE BOTTOM OF THE BOX.
C
DIMENSIONS
COVERS (FOR REPLACEMENT OR COLOR CONVERSION)
JUMPER
POSITION
J1 TO TAP A
J1 TO TAP B
J1 TO TAP C
J1 TO TAP D
J1 TO TAP D
J1 TO TAP E
J1 TO TAP F
J1 TO TAP G
TB1
MOUNTING BOX, RED FOR SURFACE OR FLUSH MOUNT REQUIRES ADAPTER PLATE
4905-9903 (THIS BOX MAY BE AVAILABLE FOR RETROFIT APPLICATIONS)
RESERVED FOR
FUTURE USE
1 1/2" DEEP EXTENSION
(38.1mm)
(RACO NO. 203)
SUPPLIED BY CONTRACTOR
CAUTION: DO NOT BRING CONDUIT THROUGH
BACK OF ELECTRICAL BOX.
8 5/16" H X 5 3/4" W X 0.060" THICK
(211 mm X 146 mm X 1.5 mm)
7 7/8" H X 5 1/8" W X 2 3/4"D
(200 mm X 130 mm X 70 mm)
ADAPTER PLATE, RED, REQUIRED TO MOUNT S/V ON 2975-9145
1
4" SQ. X 1 1/2" DEEP BOX
(101.6mm X 38.1mm)
(RACO NO. 191)
SUPPLIED BY CONTRACTOR
TrueAlert SPEAKER
JUMPER SETTINGS
AUDIBLE NOTIFICATION APPLIANCE (SPEAKER)
HIGH QUALITY VOICE AND TONE REPRODUCTION WITH TAPS
FOR 1/4, 1/2, 1W, OR 2W AT 25 OR 70.7 VRMS
UL LISTED TO STANDARD 1480
SPEAKERS ARE WIRED SEPARATELY FROM TRUEALERT
STROBE WIRING
TrueAlert VISIBLE NOTIFICATION APPLIANCE (STROBE)
XENON STROBE OUTPUT IS MANUALLY SELECTABLE FOR 15, 30,
75, 110 CANDELA OR "FACP". THE "FACP" SETTING ALLOWS THE
4100U TO PROGRAM THE CANDELA SETTING.
UL LISTED TO STANDARD 1971
SUPERVISION OF EACH INDIVIDUAL STROBE'S WIRING AND
CONNECTIONS WITH ACTIVATION AT A SYNCHRONIZED 1 Hz
FLASH RATE
MAGNETIC TEST DIAGNOSTICS TO ASSIST CHECKOUT AND TESTING
OF TRUEALERT STROBE AND WIRING
RUGGED, HIGH IMPACT, FLAME RETARTANT THERMOPLASTIC
HOUSING AVAILABLE IN RED OR WHITE (COVERS ARE AVAILABLE
SEPARATELY TO CONVERT COLORS)
LED INDICATOR CAN BE SELECTED TO DISPLAY EACH POLLING CYCLE
TO INDICATE APPLIANCE SUPERVISION
WHEN THE TRUEALERT CONTROLLER IS IN DIAGNOSTIC MODE, THE MAGNETIC
TEST PULSES THE LED TO INDICATE APPLIANCE ADDRESS AND IS SELECTABLE
TO ALSO BRIEFLY FLASH THE STROBE TO CONFIRM OPERATION
D
B
SURFACE MOUNT WHITE ADAPTER SKIRT
7 3/4" H X 5 3/8" W X 3 3/16"D
(197 mm X 137 mm X 81 mm)
DEPTH WITH S/V=5 7/8" (149mm)
C
A
REQUIRED WHEN MOUNTING TO
SURFACE MOUNTED ELECTRICAL BOX
4" SQUARE, 1 1/2" DEEP WITH
1 1/2" DEEP EXTENSION
SURFACE MOUNT RED ADAPTER SKIRT
4905-9946
AUDIBLE NOTIFICATION APPLIANCE (SPEAKER)
4905-9947
HIGH QUALITY VOICE AND TONE REPRODUCTION WITH TAPS
FOR 1/4, 1/2, 1W, OR 2W AT 25 OR 70.7 VRMS
4905-9903
UL LISTED TO STANDARD 1480
SPEAKERS ARE WIRED SEPARATELY FROM TRUEALERT
2975-9145
STROBE WIRING
TrueAlert VISIBLE NOTIFICATION APPLIANCE (STROBE)
MODEL
XENON STROBE OUTPUT IS MANUALLY SELECTABLE FOR 15, 30,
NUMBER
75, 110 CANDELA OR "FACP". THE "FACP" SETTING ALLOWS THE
4905-9996
4100 TO PROGRAM THE CANDELA SETTING.
4905-9997
UL LISTED TO STANDARD 1971
SUPERVISION OF EACH INDIVIDUAL STROBE'S WIRING AND
CONNECTIONS WITH ACTIVATION AT A SYNCHRONIZED 1 Hz
FLASH RATE
MAGNETIC TEST DIAGNOSTICS TO ASSIST CHECKOUT AND TESTING
OF TRUEALERT STROBE AND WIRING
RUGGED, HIGH IMPACT, FLAME RETARTANT THERMOPLASTIC
HOUSING AVAILABLE IN RED OR WHITE (COVERS ARE AVAILABLE
SEPARATELY TO CONVERT COLORS)
LED INDICATOR CAN BE SELECTED TO DISPLAY EACH POLLING CYCLE
TO INDICATE APPLIANCE SUPERVISION
WHEN THE TRUEALERT CONTROLLER IS IN DIAGNOSTIC MODE, THE MAGNETIC
TEST PULSES THE LED TO INDICATE APPLIANCE ADDRESS AND IS SELECTABLE
TO ALSO BRIEFLY FLASH THE STROBE TO CONFIRM OPERATION
4" SQ. X 1 1/2" DEEP BOX
(101.6mm X 38.1mm)
(RACO NO. 191)
SUPPLIED BY CONTRACTOR
DIMENSIONS
MOUNTING ADAPTERS AND BOXES
2
TrueAlert SLC (STYLE 4) SPEAKER/VISIBLE NOTIFICATION APPLIANCES 4906 SERIES
PRODUCT INFORMATION
FEATURES:
70.7V
MODEL
NUMBER
3
TM
TrueAlert ADDRESSABLE (STYLE 4) SPEAKER/VISIBLE NOTIFICATION APPLIANCES 4906 SERIES
PRODUCT INFORMATION
FEATURES:
4
B
10
A
11
J1
12
IF LAST APPLIANCE
ON CIRCUIT,
CONNECT EOLR
(SEE WIRING NOTES)
DIMENSIONS
7 1/2" DIA x 1/2"D
(191mm x 13mm)
DIMENSIONS
23 11/16" L x 13 3/8" W x .024" THK
(602 mm x 340 mm x .508 mm)
RED
RED
PROJECT NO: 1089-0001
DATE: 1.12.2015
WIRING NOTES
1. REFER TO FIELD WIRING DIAGRAMS SUPPLIED WITH THE 4100/4003 FOR ADDITIONAL NAC WIRING INFORMATION.
2. NOTIFICATION APPLIANCES ARE RATED PER INDIVIDUAL NAMEPLATE LABEL.
3. MAINTAIN CORRECT POLARITY ON TERMINAL CONNECTIONS. DO NOT LOOP WIRES UNDER TERMINALS.
4. ALL NAC WIRING CONNECTIONS ARE SUPERVISED AND POWER-LIMITED.
5. END-OF-LINE RESISTOR VALUE DEPENDENT ON CONTROL PANEL.
K
SHEET NO:
FA7.03
12
11
10
9
8
7
6
5
4
3
2
1
DSA SUBMITTAL
9
8
7
DEVICE MOUNTING HEIGHT REFERENCE (PER NFPA 72)
FIRE
FIRE
3' (MIN)
(914mm MIN)
NFPA 72 AUDIBLE APPLIANCE
6" MIN (152.4mm MIN)
BELOW FINISHED CEILING
REF. 80" MIN (IBC)
(2032mm MIN)
C
4"
(102mm)
TO BOTTOM OF LENS
48" MAX (NFPA, ADA)
42" MIN (NFPA)
CLASS 'A'
+ -
WIRING TECHNIQUES FOR SHIELDED CABLE:
EXAMPLE:
#18-2 AWG SHIELDED
TWISTED-PAIR CABLE
A
SHIELDS AND DRAINS MUST NEVER TOUCH GROUND.
MOST GROUNDS ARE DUE TO SHIELDING ISSUES.
BY CREATING A PROPER PROCEDURE FOR WIRE
HANDLING WITH ADDRESSABLE CIRCUITS
MOST GROUNDS AND SHORTS CAN BE ELIMINATED.
ALL UNSHIELDED WIRE MUST BE ENTIRELY IN GROUND CONDUIT.
PIGTAILS, (T-TAP) WIRING IS PERMITTED TO ADDRESSABLE DEVICES
FOR CLASS B CIRCUIT WIRING.
12" (MAX)
DRAIN WIRE
PREPARE THE CABLE BY
REMOVING 2" TO 4" OF
JACKET AS NEEDED.
EXAMPLE FOR
WIRING LABELING
4
WIRE
TAG
DISCARD
SHIELD
REUSE INSULATION
WALL MOUNTED
SMOKE/HEAT
DETECTOR
DOOR
WIDTH
LESS 3"
(76mm)
SIDE WALL
(1219mm)
(1219mm MAX)
(1067mm MIN)
MEASUREMENTS SHOWN ARE
TO TOP OF PULL HANDLE
9
2
N1:M
1. ALL WIRING IS TO BE COPPER CONDUCTOR. ALL EQUIPMENT MUST
BE INSTALLED IN ACCORDANCE WITH THE MANUFACTURERS
RECOMMENDATIONS AND THE SPECIFICATIONS AND STANDARDS
DRAIN WIRE
OF THE AUTHORITY HAVING JURISDICTION. THE INSTALLATION OF
ALL WIRING, CABLE AND EQUIPMENT MUST BE IN ACCORDANCE
WITH NFPA 70, NATIONAL ELECTRICAL CODE NEC), AND SPECIFICALLY
WITH ARTICLE 760, FIRE ALARM PROTECTIVE SIGNALING SYSTEMS;
ARTICLE 800, COMMUNICATION CIRCUITS, WHERE APPLICABLE.
5
2. IF SHIELDED WIRE IS USED, THE FOLLOWING MUST BE OBSERVED:
(+)
A. METALLIC CONTINUITY OF THE SHIELD MUST BE MAINTAINED AND
RED
INSULATED THROUGHOUT THE ENTIRE LENGTH OF THE CABLE.
STRIP OFF APPROX.
B. SHIELDS SHALL ONLY BE CONNECTED AT THE CONTROL UNIT.
1-2 INCHES OF
SHIELD MUST NOT BE CONNECTED TO, OR TOUCH CONDUIT, ELECTRICAL
BLACK INSULATION TO
SLIDE ONTO DRAIN WIRE.
BOXES, OR ASSOCIATED HARDWARE AT ANY POINT.
C. THE ENTIRE LENGTH OF THE CABLE MUST HAVE A RESISTANCE GREATER
THAN 1 MEGOHM TO EARTH.
(-)
D. ALL CONDUCTORS ARE TO BE FREE OF SHORTS AND GROUNDS.
BLACK
3. UNDERGROUND WIRING MUST BE LISTED FOR APPLICATION AND FREE OF ALL WATER.
4. WIRING OTHER THAN THAT CONNECTED TO ELEVATOR CABS MUST NOT BE RUN
REDUCE EXPOSED WIRES TO
IN ELEVATOR SHAFTS (REF.NFPA 70, ARTICLE 620).
ABOUT 5/16" TO 3/8" FOR
5. WIRING IN DUCTS, PLENUMS AND OTHER AIR HANDLING SPACES MUST BE LISTED
INSERTION INTO BOX-TYPE
FOR PLENUM USE AND INSTALLED IN ACCORDANCE WITH NFPA 70, ARTICLE 300.
OR SCREW-CLAMP TERMINALS.
6. SPLICING IS PERMITTED IN ACCORDANCE WITH NFPA 70. ALL JUNCTIONS MUST
BE INSULATED AS SOUNDLY AS THE ORIGINAL JACKET. CONTINUITY OF ANY SHIELD
(WHERE USED) MUST BE MAINTAINED.
7. ONLY SYSTEM WIRING CAN BE RUN IN THE SAME CONDUIT.
8. THE COMMUNICATION CIRCUIT MEETS THE OPERATIONAL CHARACTERISTICS DEFINED FOR A STYLE 4
AND STYLE 6 SIGNALING LINE CIRCUIT. MAXIMUM WIRE RUN NOT TO EXCEED 2500 FT.
9. ALL CIRCUITS ARE SUPERVISED AND POWER-LIMITED UNLESS OTHERWISE INDICATED. SHIELD WIRES ARE NOT SUPERVISED.
10. OPERATING POWER, FOR IDNet DEVICES, MUST ORIGINATE FROM A POWER-LIMITED POWER SUPPLY LISTED FOR FIRE
PROTECTIVE SIGNALING USE OR, FROM THE F.A. CONTROL PANEL POWER SUPPLIES INDICATED IN THE APPROPRIATE
DIAGRAM. MAXIMUM WIRE NOT TO EXCEED 1KM (3270 FT).
11. WHEN COMMUNICATION WIRING OR OPERATING WIRING LEAVES THE BUILDING, OVERVOLTAGE PROTECTORS ARE
REQUIRED; USE 2081-9044, INSTALL ONE WHERE IT LEAVES THE BUILDING AND ONE WHERE IT ENTERS THE NEXT BUILDING.
12. TO PREVENT CONFUSION AND POSSIBLE ERRORS, TAG ALL CONDUCTORS, CODE AT INSTALLATION, TO IDENTIFY
CIRCUIT ASSIGNMENT, POLARITY AND IN OR OUT DIRECTION OF THE WIRING. LOG ON AS-BUILTS.
13. LEAVE ADEQUATE SLACK IN THE WIRING TO ALLOW FOR TROUBLE SHOOTING.
SIMPLEXGRINNELL IS NOT RESPONSIBLE FOR ELECTRICAL CONTRACTOR'S WIRE CONDITIONS.
14. IDNet COMMUNICATION LINE SPECS.:
15. IDNET MAXIMUM NUMBER OF DEVICES:
MAX. 36 VDC @ .5A
NON-CODED 250
3333 BAUD
CODED PIEZO BASES 43 MAX.
33 MAX. LINE RESISTANCE
217 ADDRESSES STILL AVAILABLE FOR OTHER DEVICES.
FINISHED
WALL
FINISHED
FLOOR
+
PRODUCT INFORMATION
SHIELD
MAGNETIC
DOOR
HOLDER
48" MAX (ADA)
9.A
UL LISTED FIRE PROTECTIVE SIGNALING CABLES MAY BE SELECTED FROM THE SIMPLEXGRINNELL WIRE & CABLE TABLE, #WIRE TABLE
GENERAL WIRING GUIDELINES
SIMPLEX
NOTE: REFER TO THE PROPER DEVICE
INSTALLATION INSTRUCTIONS
FOR BACKBOX MOUNTING HEIGHT.
1
SIGNALING LINE (ADDRESSABLE) CIRCUITS SHIELDING EXAMPLE
TRIM AWAY ONLY
THE SHIELD AND
KEEP THE DRAIN
3
WIRE UNDAMAGED.
MANUAL
PULL
STATION
FIRE
PHONE
JACK
2
MOST SHORTS ARE SHIELD TO CONDUCTOR.
(305mm MAX)
HEAT DETECTORS
NEVER HERE
5"
(127mm)
80" MIN (ADA) (2032mm MIN)
80" MIN (NFPA) (2032mm MIN)
3
CONDUIT SYSTEM MUST HAVE A GOOD REFERENCE TO EARTH GROUND
ACCEPTED HERE
TO EXIT DOOR
5' (MAX.)
(1524mm)
96" MAX (NFPA, ADA)
(2440mm MAX)
ABOVE FINISHED FLOOR
TO TOP OF LENS
REF. 96" MAX (IBC)
(2440mm MAX)
ABOVE FINISHED FLOOR
CEILING
CEILING MOUNTED
SMOKE/HEAT
DETECTOR
SYNCHRONIZE MORE THAN
TWO APPLIANCES IN ANY
FIELD OF VIEW.
NOTE: MEASUREMENTS
SHOWN ARE TO THE
CLOSEST EDGE OF THE
DETECTOR.
4"
(102mm)
90" MIN (2286mm MIN)
ABOVE FINISHED FLOOR
(OTHER MOUNTING HEIGHTS SHALL BE
PERMITTED BY THE AHJ PROVIDING IT
MEETS THE SOUND LEVEL OUTPUT REQUIRED.)
AUDIBLE/VISUAL
& VISUAL ONLY
APPLIANCES
B
2
AUDIBLE ONLY
FIRE
THE 4" REQUIREMENT FOR SMOKE DETECTORS HAS
BEEN REMOVED FROM THE 2010 EDITION OF NFPA 72
USE ONLY UL LISTED FIRE ALARM
TWISTED SHIELDED PAIR CABLE
(TSP) FOR IDNETS, DATA COMM.
LINES, AUDIO, PHONE & SPEAKER
WIRING IN A FIRE ALARM SYSTEM.
MIN. SIZE IS 18-2 AWG SOLID STP.
CUT
4
+
CLASS 'B'
+ -
B
TO PREVENT CONFUSION AND POSSIBLE
ERRORS, ALL WIRES MUST BE TAGGED.
SEE WIRE LEGEND FOR TYPES.
WIRES MUST BE CONNECTED
SEPARATELY UNDER TERMINALS.
A CONTINUOUS WIRE LOOP
IS NOT ALLOWED.
DRAIN WIRE
ONLY CLASS B IDNET, MAPNET OR
DATA COMM. CABLE MAY BE
T-TAPPED. IT MUST BE DONE
IN A JUNCTION BOX WITH
CABLE STRAIN RELIEF I.E.
CORD CLAMP/BUSHING, AND
TAPE WRAPPED AS SHOWN HERE.
PUSH REUSED INSULATION
CAREFULLY DOWN INTO
JACKET. SECURE WITH
ELECTRICAL TAPE.
6
PHYSICAL EDUCATION BUILDING AND
RENOVATED LAB BUILDING
SAN JOSE, CALIFORNIA
DRAIN WIRE
ELECTRICAL TAPE.
7
STRIP THE INSULATED WIRES
ABOUT 5/16" TO 3/8" FOR
INSERTION INTO BOX-TYPE OR
SCREW-CLAMP TERMINALS ON
THE ADDRESSABLE DEVICE.
C
SECURE THE
DRAIN WIRES INTO
THE CONNECTOR
APPROVED FOR
THE PURPOSE.
WIRES MUST BE
TIGHT ENOUGH
TO HOLD SECURELY
AND NOT SLIP OUT
OF THE CONNECTION.
ENSURE BARE DRAINS
ARE SECURED AND
UNABLE TO MAKE
EXTERNAL CONTACT.
SEE NOTE 2
8
THE SHIELD/DRAIN IS NEVER
CONNECTED TO THE DEVICE.
TRIM THE BARE DRAIN
TO ABOUT 1-1/2". JOIN
THEM WITH AN ELECTRICAL
CONNECTOR LISTED AND
APPROVED FOR WIRE SPLICING.
NO.
INSTRUCTIONS
D
4081-9001
4081-9002
4081-9003
2.2K
733-893
3.3K
733-896
4.7K
1ST BAND
RED
2ND BAND
RED
ORANGE
YELLOW
4TH BAND
3RD BAND
GOLD
RED
ORANGE
VIOLET
5TH BAND
RED
CIRCUIT TYPE
1/2
ANNUNCIATOR (4300)
4004, 4010 (TROUBLE)
N.O. INITIATING
PULL, SMOKE, HEAT,
WATERFLOW, TAMPER, ETC.
24 PT. I/O SWITCH SUPV.
CURRENT LIMITED N.O. INITIATING
NOTIFICATION (DACT)
N.O. INITIATING
PULL, SMOKE, HEAT,
WATERFLOW, TAMPER, ETC.
4004*, 4004R, 4005*, 4006,
4100, 4120, 4100U, ZAM'S
N/A
GOLD
RED
WATTS
1
N/A
1/2
N/A
GOLD
E
4081-9004
733-886
6.8K
BLUE
GREY
RED
1/2
N/A
GOLD
CURRENT LIMITED N.O. INITIATING
(IN LINE)
733-984
1.8K
BROWN
GREY
RED
GOLD
N/A
1/2
4081-9006
733-890
560
GREEN
BLUE
BROWN
GOLD
N/A
1
N.C. INITIATING (EOLR)
4081-9007
733-891
1.2K
BROWN
RED
RED
GOLD
N/A
1
N.C. INITIATING (EOLR)
4081-9008
733-894
10K
BROWN
BLACK
ORANGE
GOLD
N/A
1/2
4081-9009
4081-9010
733-912
20
733-973
1K
RED
BLACK
BROWN
BLACK
BLACK
RED
1
N/A
GOLD
TO MR-101 RELAY COIL
N.C. INITIATING (ACROSS CONTACTS)
24 PT. I/O (ACROSS CONTACTS)
CURRENT LIMITED N.O. INITIATING
(IN SERIES WITH CONTACT)
1
N/A
GOLD
F
G
4081-9011
4081-9012
4081-9013
733-974
733-985
734-086
100
22K
4.99K
BROWN
RED
YELLOW
BLACK
RED
WHITE
BROWN
ORANGE
WHITE
GOLD
GOLD
BROWN
N/A
N/A
BROWN
1/2
1/2
1/2
4081-9014
734-092
2.4K
RED
YELLOW
RED
GOLD
N/A
1/2
4081-9015
734-093
1.5K
BROWN
GREEN
RED
GOLD
N/A
1/2
4081-9016
4081-9017
4081-9018
734-149
734-171
734-168
378-090
378-046
378-069
150K
3.9K
10K
8.2K
5.6K
12K
BROWN
ORANGE
BROWN
GRAY
GREEN
BROWN
GREEN
WHITE
BLACK
RED
BLUE
RED
YELLOW
RED
ORANGE
RED
RED
ORANGE
GOLD
GOLD
GOLD
GOLD
GOLD
GOLD
N/A
N/A
N/A
N/A
N/A
N/A
1/2
1
1
1/2
1/2
1/2
4 3/4"
7. DO NOT LOCATE POWER-LIMITED WIRING IN THE SHADED AREAS
OF THE BACKBOX, THIS AREA IS RESERVED FOR NON-POWER
LIMITED CIRCUITRY SUCH AS AC POWER, BATTERIES AND CITY
CONNECTION.
WALL STUD GUIDES
(SEE NOTE 3.)
4005
4004, 4005, 4006, 4008,
4009, 4010, 4100, 4100U
4005 8 POINT I/O
4005*, 4090-9001 IDNET IAM
4605-7401, 4100 SERIES
PKG. SIZE
1 BAY
4090-9001 IDNET IAM
4006, 4008, 4010
4003
PID NUMBER
BOX HEIGHT
2975-9407
22"
N.C. INITIATING
(SECURITY MONITORING EOLR)
4090-9001 IDNET IAM
CURRENT LIMITED N.O. INITIATING
(SECURITY MONITORING EOLR)
4090-9001 IDNET IAM
ON
H
16
32
64
2 BAY
2975-9408
40"
3 BAY
2975-9409
56"
1 BAY
2975-9410
22"
2 BAY
2975-9411
40"
5 17/32"
3 BAY
2975-9412
56"
3 17/32"
1 BAY
2975-9438
22"
2 BAY
2975-9439
40"
3 BAY
2975-9440
56"
4
5
6
7
12"
BOX LENGTH
26 1/2"
BOX DEPTH
12"
4081-9306
13 1/2"
27 7/8"
14 5/8"
4081-9308
13 1/2"
27 7/8"
14 5/8"
FLOOR
G
PRODUCT INFORMATION
4099-9020 SINGLE ACTION NO GRIP IDNet SLC ADDRESSABLE MANUAL STATION
MOUNTING INSTRUCTIONS:
1. COVER & BACKPLATE COME ASSEMBLED.
2. UNLOCK STATION, DROP COVER FORWARD
TO EXPOSE MOUNTING SCREWS.
UL LISTED
SINGLE ACTION, NO GRIP, IDNet SLC ADDRESSABLE
PULL LEVEL PROTRUDES WHEN ALARMED
TAMPER RESISTANT RESET KEY LOCK
MOUNTING: SEMI-FLUSH, SURFACE
OPERATING TEMPERATURE RANGE: 32 - 120° F
OPERATING HUMIDITY RANGE: 0 - 93% RH
ADAPTER PLATES 2099-9813 OR 2099-9814 CAN BE
USE FOR RETROFIT APPLICATIONS.
5" HIGH X 3 3/4" WIDE X 1' DEEP
SCREW TERMINALS FOR 18 TO 14 AWG WIRE
ADDRESSED BY MEANS OF AN 8 POSITION DIP SWITCH
COMPATIBLE WITH IDNet SLC/MAPNET
128
1=ON
BOX HEIGHT
2081-9280
4100-1260
4100, 4100U
4100, 4100U
4100, 4100U
70VRMS CONSTANT SUPV. NACS
SECURITY MONITORING (EOLR)
N.O. SECURITY MON. (SERIES)
N.C. SECURITY MON. (SHUNT)
8
PID NUMBER
0=OFF
MOUNTING INSTRUCTIONS:
1. COVER & BACKPLATE COME ASSEMBLED.
2. UNLOCK STATION, DROP COVER FORWARD
ARCHITECT'S STAMP
THIS DRAWING IS NOT FINAL OR TO BE USED FOR CONSTRUCTION UNTIL IT IS SIGNED BY THE ARCHITECT
AND ENGINEER.
2975-9178 OR
2975-9022 BOXES
FROM SIMPLEX OR
WIREMOLD BOX
NO. 5747 SUPPLIED
BY CONTRACTOR
H
ADDRESS DIP SWITCHES UNDER RE-SEALABLE LABEL
SEE INSTALLATION INSTRUCTIONS (574-332 FOR SETTINGS
SURFACE MOUNTING
2099-9819 (BLACK) OR
2099-9820 (BEIGE)
FLUSH ADAPTOR AVAILABLE
FROM SIMPLEX
4 11/16" SQUARE x 2 1/8" DEEP BOX
SUPPLIED BY CONTRACTOR
CONSULTANT
SEMI-FLUSH MOUNTING
PROJECT
CONTACT
INTERFACE
E N G I N E E R I N G
717 Market Street
Suite 500
San Francisco, CA 94103
TEL
415.489.7240
FAX
415.489.7289
www.interfaceengineering.com
STATION HOUSING AND PULL LEVER ARE CONSTRUCTED OF CHIP
RESISTANT AND DIRT RESISTANT, HIGH IMPACT LEXAN.
HOUSING IS RED WITH RAISED WHITE LETTERING AND PULL LEVER IS
WHITE WITH RED RAISED LETTERING.
* LEXAN IS A REGISTERED TRADEMARK OF THE GENERAL ELECTRIC CO.
J
DIP
SWITCHES
1 THRU 4
1000
0100
1100
0010
1010
0110
1110
0001
1001
0101
1101
0011
1011
0111
1111
0
16
32
48
64
80
96
112
128
144
160
176
192
208
224
240
1000
1
17
33
49
65
81
97
113
129
145
161
177
193
209
225
241
0100
2
18
34
50
66
82
98
114
130
146
162
178
194
210
226
242
1100
3
19
35
51
67
83
99
115
131
147
163
179
195
211
227
243
0010
4
20
36
52
68
84
100
116
132
148
164
180
196
212
228
244
1010
5
21
37
53
69
85
101
117
133
149
165
181
197
213
229
245
0110
6
22
38
54
70
86
102
118
134
150
166
182
198
214
230
246
1110
7
23
39
55
71
87
103
119
135
151
167
183
199
215
231
247
0001
8
24
40
56
72
88
104
120
136
152
168
184
200
216
232
248
1001
9
25
41
57
73
89
105
121
137
153
169
185
201
217
233
249
0101
10
26
42
58
74
90
106
122
138
154
170
186
202
218
234
250
1101
11
27
43
59
75
91
107
123
139
155
171
187
203
219
235
251
0011
12
28
44
60
76
92
108
124
140
156
172
188
204
220
236
252
1011
13
29
45
61
77
93
109
125
141
157
173
189
205
221
237
253
0111
14
30
46
62
78
94
110
126
142
158
174
190
206
222
238
254
1111
15
31
47
63
79
95
111
127
143
159
175
191
207
223
239
255
PULL STATIONS SHALL BE INSTALLED IN ACCORDANCE WITH NFPA 72
AND ADA GUIDE LINES.
J
CUTOUT MUST BE A MINIMUM
FLUSH MOUNTING
INTRODUCTION:
THE 4099-9020 ADDRESSABLE PULL STATION PROVIDES TWO-STATE
STATUS INFORMATION (NORMAL AND SHORT) TO THE IDNet SLC COMPATIBLE FIRE
ALARM CONTROL PANEL (FACP) VIA THE IDNet SLC CHANNEL. THE IDNet SLC
CHANNEL PROVIDES THE COMMUNICATION LINK BETWEEN PULL STATION
AND THE FACP AND POWERS THE ENTIRE CIRCUITRY.
WIRING:
1. ALL WIRING TO COMPLY WITH LOCAL CODE.
2. CONDUCTORS MUST TEST FREE OF ALL GROUNDS.
3. MAINTAIN CORRECT POLARITY
IDNet SLC
FROM FIRE ALARM CONTROL PANEL OR
OTHER IDNet SLC DEVICES ON CIRCUIT
7
1 2 3 4
SHIELD
+
-
6" HIGH BY 5" WIDE
9
SHIELD
SHIELD
+
-
11
10
9
7. MAXIMUM QUANTITY OF DEVICES PER CIRCUIT: 250
6
AL
AT
EL
E CT RICA N
E O
OR
F CAL I F
DETAILS - FIRE ALARM
DATE: 1.12.2015
5 6
1
2
1
2
3
4
3
4
5 6
8. TERMINALS 1 AND 2 FOR FIELD WIRING. TERMINALS 3 AND
4 ARE FACTORY WIRING.
9. WIRE NUT, SPLICE, OR SOLDER THE SHIELD WIRES.
7
ON LA
AS
PROJECT NO: 1089-0001
4. IDNet SLC LINES ARE TO BE 18 AWG TWISTED SHIELDED PAIR
5. MAXIMUM LINE RUN FROM PANEL TO FARTHEST DEVICE NOT
TO EXCEED 2500 FEET.
6. MAXIMUM TOTAL WIRE (INCLUDING ALL T-TAPS) FROM PANEL NOT TO
EXCEED 10,000 FEET.
8
F E S S I ON
TO ADDITIONAL IDNet SLC DEVICES OR RETURN
TO FIRE ALARM CONTROL PANEL FOR STYLE 6
APPLICATION.
K
10. IF SHIELD IS PRESENT, IT SHOULD BE CONNECTED TO THE
OUTGOING IDNet SLC SHIELD TO PROVIDE A CONTINUOUS SHIELD OVER
THE LENGTH OF THE IDNet SLC CHANNEL. SHIELD SHOULD BE
INSULATED FROM THE ELECTRICAL BOX.
11. SEE INSTALLATION INSTRUCTIONS 574-332
12
PRO
NOTE: BOX MUST BE RECESSED
INTO WALL 1" TO 1 1/8".
APPLICATION:
K
D
No. E16806
ST
0000
0000
2014-0174
Joe Ripp
I NE ER
MOUNTING INSTRUCTIONS:
1. COVER & BACKPLATE COME ASSEMBLED.
2. UNLOCK STATION, DROP COVER FORWARD
TO EXPOSE MOUNTING SCREWS.
CONSTRUCTION:
DIP SWITCHES 5 THRU 8
APPROVAL
THIS DOCUMENT CONTAINS INFORMATION THAT IS PROPRIETARY TO LPAS, INC. AND IS FURNISHED FOR THE
PURPOSES OF REVIEW, BIDDING OR CONSTRUCTION OF THE PROJECT LISTED IN THE JOB TITLE BOX ABOVE
AND SHALL NOT BE USED FOR ANY OTHER PURPOSE OR RELEASED TO ANY OTHER PARTY WITHOUT THE
WRITTEN CONSENT OF LPAS, INC. INFOMATION CONTAINED HEREIN IS AN INSTRUMENT OF PROFESSIONAL
SERVICES AND SHALL REMAIN THE PROPERTY OF LPAS, INC. ALL RIGHTS RESERVED COPYRIGHT © 2009.
TO EXPOSE MOUNTING SCREWS.
RESETTING
4099-9020 SINGLE ACTION STATION REQUIRES A KEY TO RESET
THE ACTIVATION LEVER AND DEACTIVATE THE ALARM SWITCH.
(IF OPTIONAL PLASTIC BREAK ROD WAS USED IT MUST BE REPLACED)
ADDRESS SHOWN ABOVE IS 120
SINGLE GANG EXTENSION RING 3/4"
(RACO NO. 773)
SUPPLIED BY CONTRACTOR
KNOCKOUTS FOR 3/4" CONDUIT
TOP AND BOTTOM OF BOX
4" SQUARE x
2 1/8" DEEP BOX
(RACO NO. 231 OR 232)
OR (RACO NO. 500)
SINGLE GANG SWITCH BOX
2 1/2" DEEP
SUPPLIED BY CONTRACTOR
U
3
F
ENG
2
BATTERY AREA
(IF APPLICABLE)
OPERATION:
1
CONDUIT FOR INTERNAL
PANEL HARNESSES OR
NPL WIRING.
NO CONDUIT ENTRY OR
WIRING IN THIS AREA
FIG. 1
ACTIVATION:
4099-9020 NO GRIP SINGLE ACTION STATION PROVIDES A MORE EASILY
ACTIVATED PULL LEVER FOR ANTICIPATED USERS MAY FIND THE STANDARD
STATION LEVER DIFFICULT TO ACTIVATE. COMPLETING THIS ACTION
BREAKS AN INTERNAL PLASTIC BREAK-ROD THAT IS VISIBLE BELOW THE
PULL LEVER (USE OF PLASTIC ROD IS OPTIONAL). THE PULL LEVEL LATCHES
INTO THE ALARM POSITION AND REMAINS EXTENDED OUT OF THE
HOUSING TO PROVIDE A VISIBLE INDICATION.
OFF
66"
(TYPICAL, FOR
5 FOOT HEIGHT
TO LCD DISPLAY
CENTERLINE)
WALL
DO NOT USE ADDRESS 0 FOR AN IDNET ADDRESS
8
FOR SURFACE MOUNT
USE 4 HOLES TO SECURE
BACKBOX TO WALL
SEE
CHART
TYPICAL CONDUIT LOCATION FOR
PWR. LIMITED FIELD WIRING
IDNET ADDRESSING
4
E
NOTE: ADA REQUIREMENTS LIMIT THE ALLOWABLE PROTRUSION OF OBJECTS
MOUNTED IN PUBLIC ACCESSIBLE WALKS, HALLS, CORRIDORS,
PASSAGEWAYS OR AISLES. THE 4 INCH (100mm) RESTRICTION APPLIES TO
ANY ITEM IN WHICH THE MEASUREMENT FROM THE FLOOR TO THE BOTTOM
OF THE UNIT IS MORE THAN 27 INCHES.
FEATURES:
2
EXAMPLE OF
ADDITIONAL CABINET
MOUNTING LOCATION
8. REFER TO SIMPLEX BACKBOX INSTALLATION DOCUMENT
579-117 FOR DETAILED INSTRUCTIONS.
IDNET DIP SWITCH SETTINGS
1
16"
KNOCKOUT
SCREW/NAIL
HOLES FOR
SEMI-FLUSH
MOUNT
(SEE NOTE 3.)
6. NEMA RATING: NEMA 1 - GENERAL PURPOSE.
4090-9001 IDNET IAM
ANNUNCIATOR (N2)
SPEAKER CIRCUIT
3 1/4" MIN.
10" MAX.
24"
1 7/16"
5. IF PRESENT, USE WIRE MANAGEMENT BRACKETS ON BOX SIDES
TO SECURE WIRE RUNS.
4005*, 4090-9001 IDNET IAM
4100, 4100U
NOTIFICATION
6 29/32"
4. MINIMUM DISTANCE BETWEEN ANY TWO BOXES IS 3 1/4" (6" MAXIMUM).
4605-7401, 4100 SERIES
4090-9001 IDNET IAM (EOLR)
2080-9024
4004, 4005,
4090-9001 IDNET IAM
2190-9173 MAPNETII 2 PT I/O
4-20MA ZAM (TROUBLE)
REFER TO FIG.1 FOR TYP. CONDUIT
PENETRATION LOCATIONS
11 11/16"
3. MOUNT BOX TO WALL: BOX MUST BE LEVEL AND PLUMB.
FOR SURFACE MOUNT USE TEAR DROP AND CLEARANCE HOLES
ON BACK SURFACE.
FOR SEMI-FLUSH MOUNT: USE WALL STUD GUIDES FOR MAXIMUM
ALLOWABLE BOX DEPTH TO PROVIDE OPEN DOOR CLEARANCE.
USE KNOCKOUTS ON SIDE WALL, SCREW OR NAIL BOX TO WALL STUDS.
FIRE ALARM PANEL/MODULE
4081-9005
D
2. NO KNOCKOUTS PROVIDED. CUT CONDUIT/SERVICE ENTRANCE
OPENINGS. REFER TO FIG.1 FOR PROPER LOCATIONS.
CONDUIT PROTRUSION INTO BOX 1/2" MAX.
* USE WITH RETROFIT OR HIGH CURRENT MODULE
OHMS
DATE
1. REMOVE ELECTRONIC CARD CAGE (IF PRESENT)
AND STORE IT IN A SAFE DRY AREA.
NOTE: REFER TO PANEL/MODULE AND DEVICE INSTALLATION
INSTRUCTIONS FOR PROPER TERMINATIONS.
REFERENCE
NUMBER
733-892
ISSUE
4100ES BACKBOX INSTALLATION
END-OF-LINE RESISTOR CODES
MODEL
SAN JOSE CITY
COLLEGE
L
FOR CEILING HEIGHTS LESS THAN 86" (2180mm),
THE VISUAL LENS MOUNTING HEIGHT SHALL BE
WITHIN 6" (150mm) OF THE CEILING.
1
5
IA
A
A/C SUPPLY
OR RETURN
DIFFUSER
VISUAL APPLIANCE MOUNTING HEIGHT CONSIDERATIONS IN SLEEPING ROOMS
1. MIN DISTANCE IN SLEEPING ROOMS IS 24" (610mm) FROM CEILING TO TOP OF
LENS FOR 110CD STROBES WITHIN 16' OF THE PILLOW
2. 177CD STROBES, USED IN SLEEPING ROOMS, CAN BE WITHIN THE 24" (610mm)
MINIMUM DISTANCE FROM THE CEILING. THE HIGHER INTENSITY IS TO
COMPENSATE FOR A POSSIBLE SMOKE LAYER.
6
J
10
RE
11
R EG I S T E
12
5
SHEET NO:
FA7.04
4
3
2
1
DSA SUBMITTAL