Download ET-A_PR317_SVS16-PB-08

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Transcript
E-T-A_PR317_SVS16-PB-08
Intelligent DC 24 V power distribution including Profibus-DP interface
Power distribution system SVS16 as a flexible Profibus package for
automation
Altdorf, 15.4.2010 – E-T-A Elektrotechnische Apparate GmbH, located in
Altdorf near Nürnberg, specialist for overcurrent protection and power
distribution in factory automation presents the new DC 24 V power
distribution and remote output system type SVS16. The system features a
fully-fledged Profibus-DP interface according to EN 50170 / IEC 61158,
supporting all specified baud rates up to max. 12 MBaud. The SVS16
reduces wiring times and increases diagnostic capabilities in process
control, chemical, pharmaceutical and foodstuffs industry, in steel
production and car manufacturing.
The new power distribution and remote output system type SVS16-PB-08
provides selective overcurrent protection, power distribution in load
circuits as well as switching, protection and monitoring of digital outputs
up to 10 A. Integral consistent communication of operating and error
conditions as well as switching and resetting of individual circuits on the
DC 24 V level via Profibus-DP make the SVS16 an intelligent sub-system
on the control level. The track-mountable base module SVS16-PB-08
accommodates eight electronic circuit protectors type ESX10-125 (with
reset input) or ESX10-115 (with control input) up to 10 A. They ensure
selective overcurrent protection of sensors/actuators, peripheral subassemblies etc. and their supply lines.
Alternatively the slots of the SVS16 allow the use of the solid state power
controller type E-1048-7xx. Its features and benefits include monitoring
and control of hydraulic or pneumatic solenoids, signal lamps etc. in the
E-T-A_ PR317_SVS16-PB-08
2/3
range from 0.5 A through 5 A with regard to short circuit, overload and
wire break. For larger systems a 16-way version SVS16-PB-16 can be
made available.
The 10 mm² supply terminals “plus” and “minus” for the DC 24 V supply
have been designed redundantly contrary to the “PE” terminal. All supply
terminals and the 2.5 mm² output terminals are optionally available as
screwless or screw terminals.
The integral PBM module forwards all failures of the eight circuits to the
PLC via the 9-pin Sub-D plug. The electronic circuit protectors ESX10 or
the SSRPCs 1048-7xx receive a remote reset or control command
“ON/OFF” via the same Profibus cable after an overcurrent disconnection.
In case of a single signal wiring of the SVS16-PB-08 it is not necessary to
connect at least 18 cables for signalling and control, but only one Profibus
cable. The integral Profibus module allows simultaneous transfer of
signalling and control data directly to the PLC, thus saving additional I/O
components.
Caption:
The Profibus-capable power distribution system SVS16-PB-08 provides
selective overcurrent protection, optimised power distribution and an
integral remote-out-system for automation.. (phto: E-T-A)
E-T-A Elektrotechnische Apparate GmbH
In 2008 E-T-A Elektrotechnische Apparate GmbH achieved a total turnover of
€93m and had about 1400 people on the payroll in more than 60 countries. 6
production sites, 12 subsidiaries and a great number of representatives give
impressive proof of E-T-A’s internationality. Production, Sales, Purchasing,
Market Research and Design are concentrated at the headquarters in Altdorf.
E-T-A’s product line holds a wide range of electrical protective and controlling
devices. It goes from thermal circuit breakers for equipment protection to
E-T-A_ PR317_SVS16-PB-08
3/3
complex solutions protecting electrical or electronic systems against overload
and short circuit. E-T-A serves almost every industry, e.g. process control and
automation, telecommunications, chemical and medical industry, manufacturers
of household appliances and garden equipment, aerospace, automotive and
marine industry.
For detailed information please visit E-T-A’s home page: www.e-t-a.com.
Further information:
E-T-A Elektrotechnische Apparate GmbH
Thomas Weimann
Industriestr. 2 - 8
90518 Altdorf – Germany
Phone: +49-9187-10227
Fax: +49-9187-10448
E-Mail: [email protected]
www.e-t-a.com