Download ADV3224-EVALZ/ADV3225-EVALZ/ADV3228- EVALZ/ADV3229-EVALZ User Guide UG-766

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Transcript
ADV3224-EVALZ/ADV3225-EVALZ/ADV3228EVALZ/ADV3229-EVALZ User Guide
UG-766
One Technology Way • P.O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com
Evaluation Board for the ADV3224/ADV3225/ADV3228/ADV3229
Analog Crosspoint Switch
FEATURES
GENERAL DESCRIPTION
Full featured evaluation board for the
ADV3224/ADV3225/ADV3228/ADV3229
On-board USB port for inputs and outputs control
±5 V operation
The ADV3224/ADV3225 are high speed, 16 × 8 analog crosspoint
switch matrices, and the ADV3228/ADV3229 are 8 × 8, analog
crosspoint switch matrices. These devices offer a −3 dB signal
bandwidth of greater than 750 MHz and a high slew rate of
greater than 2500 V/µs.
EVALUATION KIT CONTENTS
ADV3224-EVALZ/ADV3225-EVALZ/ADV3228-EVALZ/
ADV3229-EVALZ evaluation board
Instruction guide for software download
EQUIPMENT NEEDED
Signal source or video pattern generator and signal analyzer
Power supplies (5 V/1 A and ±5 V/1 A)
PC running Windows XP only
Type A to Type B USB 2.0 connector (recommended)
BNC-to-BNC connector for inputs and outputs
SOFTWARE NEEDED
ADV3224/ADV3225 Control Software for 16 × 8 switch array
ADV3228/ADV3229 Control Software for 8 × 8 switch array
The ADV3224/ADV3225/ADV3228/ADV3229 include eight
independent output buffers that can be placed into a high
impedance state for paralleling crosspoint outputs to prevent
off channels from loading the output bus. The ADV3224 and
ADV3228 have a gain of 1, and the ADV3225 and ADV3229
have a gain of 2, and all of the devices operate on voltage supplies
of ±5 V. Channel switching is performed via a serial digital
control that accommodates the daisy chaining of several devices,
or via a parallel control to allow updating of an individual output
without reprogramming the entire array.
The ADV3224/ADV3225/ADV3228/ADV3229 are available
in a 72-lead LFCSP package over the extended industrial
temperature range of −40°C to +85°C. Applications of these
analog crosspoint switches include routing high speed video
signals (NTSC, PAL, SECAM, YUV, RGB, MPEG, and wavelet),
data communications, and telecommunications.
This user guide provides all of the supporting documents and
software for the evaluation of the ADV3224/ADV3225/ADV3228/
ADV3229. Full specifications on these products are available in
the ADV3224/ADV3225 and ADV3228/ADV3229 data sheets,
which should be consulted in conjunction with this user guide
when working with the evaluation board.
PLEASE SEE THE LAST PAGE FOR AN IMPORTANT
WARNING AND LEGAL TERMS AND CONDITIONS.
Rev. 0 | Page 1 of 11
UG-766
ADV3224-EVALZ/ADV3225-EVALZ/ADV3228-EVALZ/ADV3229-EVALZ User Guide
TABLE OF CONTENTS
Features .............................................................................................. 1
Analog Inputs.................................................................................4
Evaluation Kit Contents ................................................................... 1
Analog Outputs .............................................................................4
Equipment Needed ........................................................................... 1
Thru Cal .........................................................................................4
Software Needed ............................................................................... 1
Evaluation Board Control Software ................................................5
General Description ......................................................................... 1
Installing the Evaluation Software ..............................................5
Revision History ............................................................................... 2
Evaluation Board Schematics and Artwork ...................................6
Evaluation Board Photograph and Functional Block Diagram ........ 3
Ordering Information .................................................................... 10
Evaluation Board Hardware.............................................................. 4
Bill of Materials ........................................................................... 10
Power Supply ................................................................................. 4
REVISION HISTORY
11/14—Revision 0: Initial Version
Rev. 0 | Page 2 of 11
ADV3224-EVALZ/ADV3225-EVALZ/ADV3228-EVALZ/ADV3229-EVALZ User Guide
UG-766
EVALUATION BOARD PHOTOGRAPH AND FUNCTIONAL BLOCK DIAGRAM
SER/PAR D0 D1 D2 D3 D4
A0
A1
A2
CLK
40-BIT SHIFT REGISTER
WITH 4-BIT
PARALLEL LOADING
DATAIN
UPDATE
40
PARALLEL LATCH
40
DECODE
8 × 5:16 DECODERS
128
12707-001
SWITCH
MATRIX
OUTPUT
BUFFER
G = +1,
G = +2
8
OUTPUTS
ADV3224/
ADV3225
SET INDIVIDUAL
OR RESET ALL
OUTPUTS TO OFF
8
ENABLE/DISABLE
CE
RESET
16
INPUTS
DATAOUT
Figure 1.
Rev. 0 | Page 3 of 11
UG-766
ADV3224-EVALZ/ADV3225-EVALZ/ADV3228-EVALZ/ADV3229-EVALZ User Guide
EVALUATION BOARD HARDWARE
The ADV3224-EVALZ/ADV3225-EVALZ/ADV3228-EVALZ/
ADV3229-EVALZ evaluation boards allow the user to easily
evaluate the ADV3224/ADV3225/ADV3228/ADV3229 in their
various modes and configurations. Figure 2 shows the typical
bench setup used to evaluate the four analog crosspoint switches.
POWER SUPPLY
These evaluation boards require a typical ±5 V power supply
for the analog circuitry and a 5 V single supply for the digital
circuitry. Connect the supplies as shown in Figure 2.
ANALOG OUTPUTS
The eight outputs of each evaluation board are terminated with
75 Ω. All eight outputs can be disabled simultaneously using the
RESET button. The waveform signal from each or from all of
the outputs can be checked using a signal analyzer such as an
oscilloscope or television.
THRU CAL
ANALOG INPUTS
Drive any or all of the inputs, IN00 to IN07, with a waveform
generator, video pattern generator, or any signal source that
can provide an input voltage between −3 V and +3 V for the
ADV3224/ADV3228, and between −1.5 V and +1.5 V for the
ADV3225/ADV3229. All the inputs are terminated with 75 Ω.
Printed circuit board (PCB) traces contribute certain errors in
the system such as crosstalk, impedance mismatch, and reflection.
To remove these errors, these evaluation boards use a response
calibration method that uses a thru. This thru cal method is used
primarily in network analyzers to compare the trace between
J25 and J26, which is the reference and is shown in Figure 2,
to the PCB traces from and to the device under test (DUT). If
errors or mismatch are measured, they are corrected by the
network analyzer.
ANALOG INPUTS
WAVEFORM/SIGNAL GENERATOR
OSCILLOSCOPE
ANALOG OUTPUTS
ANALOG INPUTS
TELEVISION
VIDEO PATTERN GENERATOR
DC POWER SUPPLY
DC POWER SUPPLY
–5V
GND
GND
+5V
+5V
PC CONTROL
THRU CAL
12707-002
TYPE A TO TYPE B USB
Figure 2. Typical Evaluation Setup
Rev. 0 | Page 4 of 11
ADV3224-EVALZ/ADV3225-EVALZ/ADV3228-EVALZ/ADV3229-EVALZ User Guide
UG-766
EVALUATION BOARD CONTROL SOFTWARE
These evaluation boards are configured with a USB friendly
interface to allow programmability of the ADV3224/ADV3225/
ADV3228/ADV3229 registers.
Parallel and serial programming, using the P1 and P3 connectors
on the evaluation board, can also be achieved. For information on
these two programming modes, refer to the ADV3224/ADV3225
and ADV3228/ADV3229 data sheets.
Note that the software can be installed in other operating
systems, such as Windows 7 or Windows 8; however, any
commands by the user in the GUI are not read and a dialog box
appears as shown in Figure 3. The same dialog box appears
when the software is activated but the USB connector is not
connected to the evaluation board.
INSTALLING THE EVALUATION SOFTWARE
2.
Download the appropriate control software, the
ADV3224/ADV3225 Control Software or the
ADV3228/ADV3229 Control Software.
Extract the .zip file and open or run the .exe file. The
graphic user interface (GUI) for the ADV3224/ADV3225
and ADV3228/ADV3229 appear as shown in Figure 4. By
default, all inputs and outputs are disabled, although an input
signal is present in the input port of the evaluation board.
Figure 3. Error Message
12707-004
1.
12707-003
The following instructions describe the procedure to install
evaluation the software onto a PC running the Windows® XP
operating system only.
Figure 4. GUI Window for ADV3224/ADV3225 (Left) and GUI Window for ADV3228/ADV3229 (Right)
Rev. 0 | Page 5 of 11
R1
Rev. 0 | Page 6 of 11
DOUT
C1
0.1µF
AGND
2kΩ
VUSB
0Ω
R7
0Ω
R6
0Ω
R5
0Ω
R4
0Ω
R3
0Ω
R2
AGND
C2
AGND
AGND .01µF
BERG69157-102
1
2
P2
RESETB
CEB
CLK
UPDATEB
A0
A1
A2
A3
D0
D1
D2
D3
D4
OSC1
ICRST
NC
NC
NC
NC
NC
NC
NC
NC
NC
1000pF
7
28
1000pF
1
2
3
4
5
6
7
8
9
10
11
12
13
14
3M3314-2002
AGND
R8
A3
AGND
2kΩ
A
C
CMD67-21VGC/TR8 (GREEN)
CR1
R9
0.47µF
C7
Figure 5. Serial, Parallel, and USB Interface Circuitry on the Evaluation Board
AGND
Y1
22pF
20.000MHZ
22pF
2
3
OSC2
C9
1
4
1MΩ
AGND
C8
OSC1
R10
NC
CR2
2kΩ
NC
A
C
D+
CMD67-21VGC/TR8 (GREEN)
DNC
NC
NC
OSC2
ICPGD
ICPGC
A0
A1
A2
A3
D0
D1
D2
D3
D4
PIC18F4550-I/PT
37
27
26
25
5
4
3
2
41
40
39
38
1
44
43
42
36
35
32
31
13
12
U1
AGND
18 MCLR/VPP/RE3
VDD1
VDD2
VUSB
17
RE2/AN7/OESPP
RB7/KBI3/PGD
16
RE1/AN6/CK2SPP
RB6/KBI2/PGC
15
RE0/AN5/CK1SPP
RB5/KBI1/PGM
14
RD7/SPP7/P1D
RB4/AN11/KBI0/CSSPP
11
RD6/SPP6/P1C
RB3/AN9/CCP2/VPO
10
RD5/SPP5/P1B
RB2/AN8/INT2/VMO
9
RD4/SPP4
RB1/AN10/INT1/SCK/SCL
8
RD3/SPP3
RB0/AN12/INT0/FLT0/SDI/SDA
24
RD2/SPP2
RA5/AN4/SS/HLVDIN/C2OUT
23
RD1/SPP1
RA4/T0CKI/C1OUT/RCV
22
RD0/SPP0
RA3/AN3/VREF+
21
RC7/RX/DT/SDO
RA2/AN2/VREF-/CVREF
20
RC6/TX/CK
RA1/AN1
19
RC5/D+/VP
RA0/AN0
30
RC4/D-/VM
OSC1/CLKI
33
RC2/CCP1/P1A
NC/ICRST/ICVPP
34
RC1/T1OSI/CCP2/UOE
NC/ICPORTS
RC0/T1OSO/T13CKI
OSC2/CLKO/RA6
NC/ICDT/ICPGD
NC/ICCK/ICPGC
VSS1
VSS2
6
29
AGND1
1
P1
AGND
C6
C4
C5
0.1µF
VUSB
0.1µF
C3
VUSB
RED
ICPGD
ICPGC
ICRST
VUSB
AGND
AGND
PLACE NEAR
USB CONNECTOR
C10
10µF
VUSB
AGND
1
4
5
P4
4-1734376-8
AGND
1
2
3
4
5
6
2
3
6
DD+
AGND
P3
PIN1 DESIGNATOR
SAMTECTSW10608GS6PIN
VUSB
CMD67-21VGC/TR8 (GREEN)
PLACE NEAR OTHER LEDS
2kΩ
VUSB
AGND
C
DIN
UPDATEB
CEB
CLK
RESETB
TP11SH9CBE
RESET
1
3
1
R11
A
P
1
CR3
N
PLACE BETWEEN ADJACENT VDD/VSS PINS
12707-005
UG-766
ADV3224-EVALZ/ADV3225-EVALZ/ADV3228-EVALZ/ADV3229-EVALZ User Guide
EVALUATION BOARD SCHEMATICS AND ARTWORK
1
1
1
1
1
1
1
J8
1
2
1
AVEE_B
108-0740-001
1
AVCC_B
108-0740-001
AGND
2 3 4 5
1
AGND
2 3 4 5
J7
AGND
2 3 4 5
J6
AGND
2 3 4 5
2
J5
BERG69157-102
P5
AGND
2 3 4 5
J4
AGND
2 3 4 5
J3
AGND
2 3 4 5
J2
AGND
3 4 5
J1
1
1
1
AVEE
AVCC
AVEE
DVCC
AVCC
DVCC
AGND
R14
75Ω
J9
1
1
AGND
J11
1
RN3
3
6
22Ω
AGND
R18
75Ω
AGND
1
1
AGND
2 3 4 5
J14
1
R22
75Ω
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
PAD
RN3
8
1
22Ω
AGND
R21
75Ω
AGND
AVCC
IN08
AVEE
IN09
AVCC
IN10
AVEE
IN11
AVCC
IN12
AVEE
IN13
AVCC
IN14
AVEE
IN15
AGND
AVEE
AGND
R20
75Ω
RN3
7
2
22Ω
AGND
R19
75Ω
AGND
2 3 4 5
J16
AGND
2 3 4 5
J15
AGND
2 3 4 5
RN3
4
5
22Ω
AGND
R17
75Ω
2 3 4 5
J10
AGND
R16
75Ω
2 3 4 5
AGND
R15
75Ω
JUMPER P5 - TIES AVCC AND DVCC
1
DVCC_B
108-0740-001
AGND
R13
75Ω
AGND
2 3 4 5
J13 1
AGND
2 3 4 5
J12 1
AGND
AGND
R25
75Ω
AGND
AGND
IN07
AVEE
IN06
AVCC
IN05
AVEE
IN04
AVCC
IN03
AVEE
IN02
AVCC
IN01
AVEE
IN00
AGND
DVCC
GEN_QFN72_10X10_PAD7_7X7_7
DUT
PAD
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
AVCC
OUT07
AVEE
OUT06
AVCC
OUT05
AVEE
OUT04
AVCC
OUT03
AVEE
OUT02
AVCC
OUT01
AVEE
OUT00
AVCC
AVEE
J18
J17
R28
75Ω
1
AGND
5 4 3 2
1
AGND
5 4 3 2
AGND
AGND
1
D1 D2
AGND
5 4 3 2
1
22Ω
1
J24
AGND
1
1
P6
1
2
AGND
BERG69157-102
UPDATB SERB
D3 D4
1
DIN
J23 5 4 3 2
D0
1
RN2
8
A2
1
5 4 3 2
RN2
2
7
22Ω
1 J22
A1
1
A0
1
RESETB CEB DOUT CLK
AGND
5 4 3 2
1
J20
5 4 3 2
1
AGND
J21
RN2
3
6
22Ω
1
J19
5 4 3 2
54
AGND
53
RESETB
52
CEB
51
DOUT
50
CLK
49
DIN
48 UPDATEB
47
SERB
46
A0
45
A1
44
A2
43
D0
42
D1
41
D2
40
D3
39
D4
38
AGND
37
DVCC
U2
RN2
5
4
22Ω
R26
75Ω
R27
75Ω
1
R23
75Ω
1
AGND
1
AGND
1
R24
75Ω
1
AGND
1
Rev. 0 | Page 7 of 11
AGND_B
108-0740-001
1
1
Figure 6. DUT Schematic on the Evaluation Board
C11
.01UF
AGND
AGND
R12
10kΩ
DVCC
RESETB
CEB
DOUT
CLK
DIN
UPDATEB
SERB
A0
A1
A2
D0
D1
D2
D3
D4
JUMPER P6 - FOR SETTING SERIAL
OR PARALLEL MODE
1
1
AGND
ADV3224-EVALZ/ADV3225-EVALZ/ADV3228-EVALZ/ADV3229-EVALZ User Guide
UG-766
12707-006
C14
Rev. 0 | Page 8 of 11
Figure 7. Decoupling Network on the Evaluation Board
C13
AVCC
AVCC
0.01µF
C16
1000pF
C17
C12
10 X 1000pF CAPS BETWEEN AVCC AND AGND
10 X 00.01µF CAPS BETWEEN AVCC AND AGND
10 X 0.1µF CAPS BETWEEN AVCCC AND AGND
0.1µF
C21
0.1µF
C24
0.1µF
C27
0.1µF
C30
0.1µF
C33
0.1µF
C36
AGND
AGND
AGND
0.1µF
C39
0.1µF
AVEE
AVEE
AVEE
0.1µF
C45
0.1µF
C48
10 X 00.01µF CAPS BETWEEN AVEE AND AGND
0.1µF
C51
0.1µF
C54
0.1µF
C57
0.1µF
C60
0.1µF
C63
10 X 0.1µF CAPS BETWEEN AVEE AND AGND
10 X 1000pF CAPS BETWEEN AVEE AND AGND
DECOUPLING NETWORK
0.1µF
C66
AGND
AGND
AGND
0.1µF
C69
0.1µF
AVCC
4 X 00.01µF CAPS
BETWEEN DVCC AND AGND
DVCC
3 X 1000pF CAPS
BETWEEN AVCC AND AVEE
AVCC
C72
0.01µF
C75
0.01µF
C78
AVEE
0.01µF
3 X 00.01µF CAPS
BETWEEN AVCC AND AVEE
1000pF
0.1µF
C15
0.1µF
C18
0.01µF
C22
0.01µF
C25
0.01µF
C28
0.01µF
C31
0.01µF
C34
0.01µF
C37
0.01µF
C40
0.01µF
C42
C43
0.01µF
C46
1000pF
C47
0.01µF
C52
0.01µF
C55
0.01µF
C58
0.01µF
C61
0.01µF
C64
0.01µF
C67
0.01µF
C70
0.01µF
C73
1000pF
C76
1000pF
C79
AVEE
AVCC
0.01µF
C19
1000pF
C20
1000pF
C23
1000pF
C26
1000pF
C29
1000pF
C32
1000pF
C35
1000pF
C38
1000pF
C41
1000pF
C44
0.01µF
C49
1000pF
C50
1000pF
C53
1000pF
C56
1000pF
C59
1000pF
C62
1000pF
C65
1000pF
C68
1000pF
C71
1000pF
C74
0.01µF
C77
0.01µF
C80
0.01µF
C81
AGND
0.01µF
3 X 1000pF CAPS
BETWEEN DVCC AND AVEE
DVCC
1000pF
C82
0.01µF
C84
DVCC
3 X 00.01µF CAPS
BETWEEN DVCC AND AVEE
C83
1000pF
C85
1000pF
C87
AVEE
0.01µF
C86
AVEE
0.01µF
12707-007
UG-766
ADV3224-EVALZ/ADV3225-EVALZ/ADV3228-EVALZ/ADV3229-EVALZ User Guide
12707-008
ADV3224-EVALZ/ADV3225-EVALZ/ADV3228-EVALZ/ADV3229-EVALZ User Guide
12707-009
Figure 8. Evaluation Board Top View
Figure 9. Evaluation Board Bottom View
Rev. 0 | Page 9 of 11
UG-766
UG-766
ADV3224-EVALZ/ADV3225-EVALZ/ADV3228-EVALZ/ADV3229-EVALZ User Guide
ORDERING INFORMATION
BILL OF MATERIALS
Table 1.
Qty
21
1
2
Location
A0 to A3, D0 to D4, CEB,
CLK, DIN, AGND, AVCC,
AVEE, DOUT, DVCC, SERB,
AGND1, RESETB, UPDATB
AGND_B, AVCC_B,
AVEE_B, DVCC_B
C1, C3, C5, C12, C15, C18,
C21, C24, C27, C30, C33,
C36, C39, C42, C45, C48,
C51, C54, C57, C60, C63,
C66, C69
C10
C2, C11, C13, C16, C19, C22,
C25, C28, C31, C34, C37,
C40, C43, C46, C49, C52,
C55, C58, C61, C64, C67,
C70, C72, C74, C75, C77,
C78, C80 to C82, C84, C86
C4, C6, C14, C17, C20,
C23, C26, C29, C32, C35,
C38, C41, C44, C47, C50,
C53, C56, C59, C62, C65,
C68, C71, C73, C76, C79,
C83, C85, C87
C7
C8, C9
3
CR1 to CR3
Diode, SMD, LED
26
1
J1 to J26
P1
3
1
1
4
1
1
16
6
1
2
P2, P5, P6
P3
P4
R1, R8, R9, R11
R10
R12
R13 to R28
R2 to R7
RESET
RN2, RN3
1
U1
1
U2
1
VUSB
Connector, PCB, coaxial, BNC, ST
Connector, PCB, header, shrouded, ST,
14P, male
Connector, PCB, Berg, jumper, ST, male, 2P
Connector, PCB, Berg, header, ST, male, 6P
Connector, PCB, USB Type B, R/A, thru hole
Resistor, precision, thick film chip, R0402
Resistor, precision, thick film chip, R0402
Resistor, precision, thick film chip, R0402
Resistor, precision, thick film chip, R0402
Resistor, film, SMD, 0402
Switch, SPST, ST, push button
Resistor, network, 8-pin, 4 resistors,
surface mount
IC, other, high performance USB
microcontrollers
Generic QFN72_10X10_PAD7_7X7_7
footprint chip
Connector, PCB, test point, red
1
Y1
IC, crystal oscillator
4
23
1
32
28
Description
Connector, PCB, pin, Vector
Value
K24A W. EYELET T15.23
Manufacturer
Vector
Part Number
K24A W. EYELET T15.23
Connector, PCB, banana jack, uninsulated,
STD (version 2 footprint)
Capacitor, ceramic, X7R, 0402
108-0740-001
Johnson
108-0740-001
0.1 µF
Murata
GRM155R71C104KA88D
Capacitor, tantalum, chip
Capacitor, ceramic, X7R, 0402
10 µF
0.01 µF
AVX
Panasonic
TPSD106K035R0125
ECU-E1C103KBQ
Capacitor, ceramic, SMD, 0402
1000 pF
Panasonic
ECU-E1E102KBQ
Capacitor, ceramic, X5R, 0402
Capacitor, ceramic
0.47 µF
22 pF
LMK105BJ474KV-F
0402CG220J9B200
CMD67-21VGC/TR8
(green)
STETCOJ01001A1944
3M3314-2002
Taiyo
Phycomp
(Yageo)
Chicago
Miniature Lamp
STETCO
3M
J01001A1944
3314-2002
BERG69157-102
SAMTECTSW10608GS6PIN
4-1734376-8
2 kΩ
1 MΩ
10 kΩ
75 Ω
0Ω
TP11SH9CBE
22 Ω
Berg
Samtec
AMP
Panasonic
Panasonic
Panasonic
Panasonic
Panasonic
C&K
CTS
69157-102
TSW-106-08-G-S
4-1734376-8
ERJ-2RKF2001X
ERJ-2RKF1004X
ERJ-2RKF1002X
ERJ-2RKF75R0X
ERJ-2GE0R00X
TP11SH9CBE
742C083220JCT
PIC18F4550-I/PT
Microchip
Technology
Not applicable
PIC18F4550-I/PT
GEN_QFN72_10X10_
PAD7_7X7_7
Red
20.000 MHz
Rev. 0 | Page 10 of 11
Components
Corp
ECS
CMD67-21VGC/TR8
GEN_QFN72_10X10_
PAD7_7X7_7
TP-104-01-02
ECS-200-20-18
ADV3224-EVALZ/ADV3225-EVALZ/ADV3228-EVALZ/ADV3229-EVALZ User Guide
UG-766
NOTES
ESD Caution
ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection
circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.
Legal Terms and Conditions
By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions
set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you
have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices, Inc.
(“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal,
temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided
for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional
limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term
“Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including
ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may
not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to
promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any
occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board.
Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice
to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO
WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED
TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL
PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF
THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE
AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable
United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of
Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby
submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed.
©2014 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
UG12707-0-11/14(0)
Rev. 0 | Page 11 of 11
Document related concepts
no text concepts found
Similar