Survey
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
IS 230 Inductive switches Dimensioned drawing IS 230…-22E… en 02-2010/03 50110211 IS 230…-10E… 10 mm 22 mm 10 - 30 V DC 1,2 kHz Embedded z Slim and short cylindrical metal housing M30 z Chromium-plated brass housing z Built-in short circuit protection, inductive protection and polarity reversal protection z LED for switching state visible from 360° Tightening torque of the fastening nuts < 40Nm ! We reserve the right to make changes • DS_IS_230_E_en.fm A B C UL Electrical connection US LISTED IEC 60947... IEC 60947... Active surface Yellow indicator diode Cable IP 67 Accessories: (available separately) z M12 connectors (KD … ) z Ready-made cables (K-D …) z Mounting clamp (MC 030…) M12 connector …NO… (normally open) …NO…-S12 (normally open): …NC…-S12 (normally closed): …NC… (normally closed) 3-pin or 4-pin M12 connection cables can be used. only 4-pin M12 connection cables can be used. Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.ctiautomation.net - Email: [email protected] IS 230 Specifications Tables General specifications Type of installation Typ. operating range limit Sn Operating range Sa IS 230…-10E… IS 230…-22E… embedded installation 10.0mm 0 … 8.1mm 22.0mm 0 … 17.8mm Electrical data Operating voltage UB 1) Residual ripple σ Output current IL Open-circuit current I0 Residual current Ir Switching output/function Voltage drop Ud Hysteresis H of Sr Temperature drift of Sr Repeatability …/4NO… …/4NC… …/2NO… …/2NC… 10 … 30VDC ≤ 20% of UB ≤ 200mA ≤ 10mA ≤ 100μA PNP transistor, make-contact (NO) PNP transistor, break-contact (NC) NPN transistor, make-contact (NO) NPN transistor, break-contact (NC) ≤ 2V ≤ 10% ≤ 10% 2) ≤ 5% 3) Reduction factors: for Sn = 10.0mm Steel Fe360 1 Copper 0.40 Aluminum 0.45 Brass 0.55 Stainless steel 0.80 for Sn = 22.0mm Steel Fe360 1 Copper 0.35 Aluminum 0.40 Brass 0.45 Stainless steel 0.66 Mounting Embedded installation: ≥ 3Sn d D2 d D3 D1 Timing Switching frequency f Delay before start-up 1.2kHz ≤ 300ms 200Hz ≤ 200ms Indicators Yellow LED (visible from 360°) switching state chromium-plated brass 30 x 30mm², Fe360 66 x 66mm², Fe360 PBTP approx. 155g/approx. 210g M12 connector 4-pin or cable: 2m, PVC, 3 x 0.34mm², Ø 5.0mm Environmental data Ambient temperature Protection class Protective circuit 4) Standards applied Electromagnetic compatibility -25°C … +70°C IP 67 1, 2, 3 IEC/EN 60947-5-2 IEC 60255-5 IEC 61000-4-2 IEC 61000-4-3 IEC 61000-4-4 ≥ 3Sn Ferromagnetic and non-ferromagnetic materials Sn [mm] D1 [mm] D2 [mm] D3 [mm] 10.0 22.0 1kV Level 3 air 8kV (ESD) Level 3 10V/m (RFI) Level 3 2kV (Burst) d Housing Standard surface plate Active surface Weight (M12 plug/cable) Connection type d Mechanical data 0 6.0 30.0 50.0 10.0 22.0 Diagrams Models with Sn = 10.0mm 1) Observe the safety regulations and installation instructions regarding power supply and wiring; for UL applications: only for use in "Class 2" circuits acc. to NEC 2) Over the entire operating temperature range 3) For UB = 20 … 30VDC, ambient temperature Ta = 23°C ± 5°C 4) 1=polarity reversal protection, 2=short circuit protection, 3=inductive protection for all outputs Order guide The sensors listed here are preferred types; current information at Leuze website. Designation Part No. Sn = 10mm IS 230 MM/4NO-10E IS 230 MM/4NO-10E-S12 IS 230 MM/4NC-10E-S12 IS 230 MM/2NO-10E-S12 50109712 50109713 50111871 50109714 Sn = 22mm IS 230 MM/4NO-22E IS 230 MM/4NO-22E-S12 IS 230 MM/4NC-22E-S12 IS 230 MM/2NO-22E 50109720 50109721 50109722 50109723 Inductive switch Standard surface plate Models with Sn = 22.0mm Inductive switch Standard surface plate Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.ctiautomation.net - Email: [email protected] IS 230 Inductive switches Type key I S 2 3 0 M M / 4 N O - 1 0 E - S 1 2 Operating principle / construction IS Inductive switch / Standard Series 230 Series with M30 x 1.5 external thread Housing / thread MM Metal housing (active surface: plastic) / metric thread Output function 4NO PNP transistor, make-contact (NO) 4NC PNP transistor, break-contact (NC) 2NO NPN transistor, make-contact (NO) 2NC NPN transistor, break-contact (NC) Measurement range / type of installation 10E Typ. scan range limit 10.0mm / embedded installation 22E Typ. scan range limit 22.0mm / embedded installation Electrical connection N/A Cable, PVC, standard length 2000mm S12 M12 connector, 4-pin, axial 200-S12 Cable, PVC, length 200mm with M12 connector, 4-pin, axial Remarks z Approved purpose: The inductive switches are electronic sensors for the inductive, contactless detection of objects. This product may only be used by qualified personnel and must only be used for the approved purpose. This sensor is not a safety sensor and is not to be used for the protection of persons. Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.ctiautomation.net - Email: [email protected] IS 230 Specifications Tables General specifications Type of installation Typ. operating range limit Sn Operating range Sa IS 230…-15N… IS 230…-40N… non-embedded installation 15.0mm 0 … 12.1mm 40.0mm 0 … 32.4mm Electrical data Operating voltage UB 1) Residual ripple σ Output current IL Open-circuit current I0 Residual current Ir Switching output/function Voltage drop Ud Hysteresis H of Sr Temperature drift of Sr Repeatability …/4NO… …/4NC… …/2NO… …/2NC… 10 … 30VDC ≤ 20% of UB ≤ 200mA ≤ 10mA ≤ 100μA PNP transistor, make-contact (NO) PNP transistor, break-contact (NC) NPN transistor, make-contact (NO) NPN transistor, break-contact (NC) ≤ 2V ≤ 15% ≤ 10% ≤ 10% 2) ≤ 5% 3) Reduction factors: for Sn = 15.0mm Steel Fe360 1 Copper 0.43 Aluminum 0.49 Brass 0.53 Stainless steel 0.84 for Sn = 40.0mm Steel Fe360 1 Copper 0.37 Aluminum 0.42 Brass 0.47 Stainless steel 0.78 Mounting Non-embedded installation: ≥ 3Sn d D2 d D3 D1 Timing Switching frequency f Delay before start-up 700Hz ≤ 300ms 100Hz ≤ 200ms Indicators switching state chromium-plated brass 45 x 45mm², Fe360 120 x 120mm², Fe360 PBTP approx. 145g/approx. 210g M12 connector 4-pin or cable: 2m, PVC, 3 x 0.34mm², Ø 5.0mm -25°C … +70°C IP 67 1, 2, 3 IEC/EN 60947-5-2 IEC 60255-5 IEC 61000-4-2 IEC 61000-4-3 IEC 61000-4-4 ≥ 3Sn Ferromagnetic and non-ferromagnetic materials Sn [mm] 15.0 Environmental data Ambient temperature Protection class Protective circuit 4) Standards applied Electromagnetic compatibility d Housing Standard surface plate Active surface Weight (M12 plug/cable) Connection type 1kV Level 3 air 8kV (ESD) Level 3 10V/m (RFI) Level 3 2kV (Burst) 1) Observe the safety regulations and installation instructions regarding power supply and wiring; for UL applications: only for use in "Class 2" circuits acc. to NEC 2) Over the entire operating temperature range 3) For UB = 20 … 30VDC, ambient temperature Ta = 23°C ± 5°C 4) 1=polarity reversal protection, 2=short circuit protection, 3=inductive protection for all outputs d Yellow LED (visible from 360°) Mechanical data 40.0 D1 [mm] 13.0 Fe360: Aluminum: Brass: Stainless steel: D2 D3 [mm] [mm] 45.0 35.0 25.0 120.0 25.0 20.0 15.0 30.0 Diagrams Models with Sn = 15.0mm Order guide The sensors listed here are preferred types; current information Leuze website. Sn = 15mm Sn = 40mm Designation Part No. IS 230 MM/4NO-15N IS 230 MM/4NO-15N-S12 IS 230 MM/2NO-15N 501 09716 501 09717 501 09718 IS 230 MM/4NO-40N IS 230 MM/4NO-40N-S12 IS 230 MM/2NO-40N 501 09726 501 09727 501 09728 Inductive switch Standard surface plate Models with Sn = 40.0mm Inductive switch Standard surface plate Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.ctiautomation.net - Email: [email protected] IS 230 Inductive switches Type key I S 2 3 0 M M / 4 N O - 1 5 N - S 1 2 Operating principle / construction IS Inductive switch / Standard Series 230 Series with M30 x 1.5 external thread Housing / thread MM Metal housing (active surface: plastic) / metric thread Output function 4NO PNP transistor, make-contact (NO) 4NC PNP transistor, break-contact (NC) 2NO NPN transistor, make-contact (NO) 2NC NPN transistor, break-contact (NC) Measurement range / type of installation 15N Typ. scan range limit 15.0mm / non-embedded installation 40N Typ. scan range limit 40.0mm / non-embedded installation Electrical connection N/A Cable, PVC, standard length 2000mm S12 M12 connector, 4-pin, axial 200-S12 Cable, PVC, length 200mm with M12 connector, 4-pin, axial Remarks z Approved purpose: The inductive switches are electronic sensors for the inductive, contactless detection of objects. This product may only be used by qualified personnel and must only be used for the approved purpose. This sensor is not a safety sensor and is not to be used for the protection of persons. Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.ctiautomation.net - Email: [email protected]